bearing MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

ENGINE – T iming Belt 11-27
(3) Make sure that the relationship between the tensioner
pulley center and the bolt center is as shown in the
illustration.
(4) Move the tensioner “B” in the direction of arrow while
lifting with a finger to give a sufficient tension to the tension
side of timing belt. In this condition, tighten bolt to secure
tensioner “B” . When the bolt is tightened, use care to
prevent shaft from turning together. If shaft is turned
together, belt will be overtensioned.
 H
CRANKSHAFT BOLT TIGHTENING
 I
OIL PUMP SPROCKET INSTALLATION
(1) Block the counterbalance shaft in the same way as at the disassembly to prevent it from turning.
(2) Install the oil pump sprocket.
(3) Apply a proper amount of engine oil to the bearing surfaces
of the flange nuts.
(4) Tighten the flange nuts to the specified torque.
 J
AUTO TENSIONER INSTALLATION
(1) If the auto tensioner rod is in its fully extended position, reset it as follows.
a. Clamp the auto-tensioner in the vise with soft jaws.
b. Push in the rod little by little with the vise until the
set hole A in the rod is aligned with the hole B in
the cylinder.
Tensioner “B”
Timing belt “B”
Tension side
of timing belt
Center of
tensioner
pulley
Center
of bolt
6EN0564
6AE0049
A
B

MANUAL TRANSMISSION – Transmission Assembly22A-8
16 18
Unit: Nm {kgfm}
52 {5.3}*
19
17
9
10
12
1315
1214
69 {7.0} 69 {7.0} 15 – 33
{1.5 – 3.4} 39 {4.0}59 – 71
{6.0 – 7.2} 26 – 33
{2.7 – 3.4}48 {4.9}
52 {5.3}*
Lifting up of the vehicle
9. Stabilizer bar connection
10. Wheel speed sensor cable connec-
tion
11. Brake hose clamp
12. Tie rod end connection
13. Lower arm ball joint connection
A
Clutch release bearing connection
14. Centermember assembly
B15. Drive shaft connection
B16. Drive shaft connection

Strut assembly
(Refer to GROUP 33A.)C17. Output shaft

Air hose A
(Refer to GROUP 15 – Intercooler.)
18. Transmission assembly lower part
coupling bolts
19. Transmission assembly
Caution
Mounting locations marked by * should be
provisionally tightened, and then fully tightened
when the body is supporting the full weight of the
engine.

MANUAL TRANSMISSION – Transmission Assembly22A-9
REMOVAL SERVICE POINTS
ACLUTCH RELEASE BEARING SEPARATION
(1) Remove the cover from the service hole in the clutch
housing.
(2) While pushing the release fork by hand in the direction
A, insert a flap-tip screwdriver between the release bearing
and the wedge collar.
Caution
Be sure to push the release fork in the direction A
before inserting a screwdriver.
(3) Separate the release bearing from the wedge collar by
prying with the screwdriver (turning the screwdriver grip
90).
NOTE
The release fork is forced to move fully in the direction
B by the return spring as soon as it is separated from
the wedge collar.
Caution
If it is hard to turn the screwdriver (to pry off the
release bearing), remove the screwdriver once and
repeat the above procedure after pushing the release
fork fully in the direction A two to three times. Forcibly
prying can cause the release bearing to be damaged.
BDRIVE SHAFT / DRIVE SHAFT
DISCONNECTION
(1) To disconnect the left-hand drive shaft, insert a lever
as shown and pry out the shaft from the transmission.
To disconnect the right-hand drive shaft, apply a lever
and a hammer as shown and lever out the shaft from
the transfer assembly using the hammer as a fulcrum.
NOTE
Remove the drive shafts with the hub and knuckle
attached.
Caution
Do not attempt to pull out the drive shaft from the
BJ in this stage since it can cause the TJ to be
damaged. Be sure to remove the drive shaft first from
the transmission side using a lever.
(2) Suspend the removed drive shaft with a wire so that
there are no sharp bends in any of the joints.
COUTPUT SHAFT REMOVAL
(1) Use the special tools (MB991612, MB990211) to remove
the output shaft.
(2) Use a shop towel to cover the transmission case not
to let foreign material get into it.
Service hole
Release fork
Wedge collar
Release bearing
Trans-
mission
side
Lever
Projection
Hammer
Lever
Output shaft
Transmission caseMB990211
MB991612

MANUAL TRANSMISSION OVERHAUL –
Specifications /
Service Specifications22B-4
SPECIFICATIONS
TRANSMISSION MODEL TABLE
Transmission modelGear ratioSpeedometer gear ratioFinal gear ratioFront LSD
W5M51-1-X6AA29/364.529Not available
W5M51-1-X6A1A29/364.529Available
W5M51-1-X7AA30/364.529Not available
W5M51-1-X7A1A30/364.529Available
W5M51-1-Z6AB29/364.875Not available
W5M51-1-Z6A1B29/364.875Available
W5M51-1-Z7AB30/364.875Not available
W5M51-1-Z7A1B30/364.875Available
GEAR RATIO TABLE
AB
1st2.785←
2nd1.950←
3rd1.4071.444
4th1.0311.096
5th0.7610.825
Reverse3.416←
Transfer gear ratio0.3018←
SERVICE SPECIFICATIONS
ItemsAllowable rangeLimit
Input shaft end play mm0.05 – 0.17–
Input shaft front bearing clearance mm0 – 0.12–
Input shaft rear bearing clearance mm0 – 0.12–
Input shaft 5th speed gear clearance mm0 – 0.09–
Output shaft preload mm0.13 – 0.18–
Output shaft bearing clearance mm0 – 0.09–
Output shaft 3rd speed gear clearance mm0 – 0.09–
Center differential case preload mm0.05 – 0.11–
Center differential case pinion backlash mm0.025 – 0.150–
Synchronizer ring back surface to gear clearance mm–0.5

Lubricants / Snap Rings, Spacers
and Thrust Plates for Adjustment MANUAL TRANSMISSION
OVERHAUL –22B-6
LUBRICANTS
TRANSMISSION
ItemsSpecified lubricants
Drive shaft oil seal lip areaDIA QUEEN MULTI-GEAR OIL 75W/85W
(Transmission oil)
Input shaft oil seal lip area
(Transmission oil)
Control shaft oil seal lip area
Select lever shoeMOLYWHITE TA No.1 or No.2
TRANSFER
ItemsSpecified lubricants
Drive shaft oil seal lip areaDIA QUEEN MULTI-GEAR OIL 75W/85W
(Transmission oil)
Front differential oil seal lip area
(Transmission oil)
O-rings
SNAP RINGS, SPACERS AND THRUST PLATES FOR
ADJUSTMENT
Part nameThickness mmIdentification symbolPart No.
Spacer
(For adj stment of inp t shaft end pla )
1.3434MD723600
(For adjustment of input shaft end play)1.4343MD723603
1.5252MD723606
1.6161MD723609
1.7070MD756760
1.7979MD756763
Snap ring
(For adj stment of inp t shaft front bearing
1.43Green (2)MD746708
(For adjustment of input shaft front bearing
clearance)1.51White (2)MD746709
1.59Yellow (2)MD746710
Snap ring
(For adj stment of inp t shaft rear bearing
1.44NoneMD746602
(For adjustment of input shaft rear bearing
clearance)1.51BlueMD746603
1.58BrownMD746604

Snap Rings, Spacers and Thrust Plates
for Adjustment MANUAL TRANSMISSION
OVERHAUL –22B-8
Part namePart No. Identification symbol Thickness mm
Snap ring
(For adj stment of o tp t shaft bearing clear
1.36YellowMD748449
(For adjustment of output shaft bearing clear-
ance)1.40GreenMD748450
1.44NoneMD746602
1.48BlackMD748451
1.51BlueMD746603
1.55WhiteMD748452
1.58BrownMD746604
1.63OrangeMD748453
1.68BlueMD748454
Snap ring
(For adj stment of o tp t shaft 3rd speed gear
2.81NoneMD746594
(For adjustment of output shaft 3rd speed gear
clearance)2.85BlueMD746595
2.89BrownMD746596
2.93YellowMD746597
2.97GreenMD746598
3.01BlackMD746599
3.05WhiteMD746600
3.09OrangeMD746601
Spacer
(For adj stment of center differential case
0.7474MD727660
(For adjustment of center differential case
preload)0.7777MD754476p
0.8080MD727661
0.8383MD720937
0.8686MD720938
0.8989MD720939
0.9292MD720940
0.9595MD720941
0.9898MD720942
1.0101MD720943
1.0404MD720944
1.0707MD720945
1.10JMD710454
1.13DMD700270
1.16KMD710455

Snap Rings, Spacers and Thrust Plates
for Adjustment / Torque Specifications MANUAL TRANSMISSION
OVERHAUL –22B-9
Part namePart No. Identification symbol Thickness mm
Spacer
(For adj stment of center differential case
1.19LMD710456
(For adjustment of center differential case
preload)1.22GMD700271p
1.25MMD710457
1.28NMD710458
1.31EMD706574
Spacer
(For adj stment of center differential case pinion
0.6–MD748362
(For adjustment of center differential case pinion
backlash)0.7–MD748363
0.8–MD748364
0.9–MD748365
1.0–MD748366
1.1–MD748367
TORQUE SPECIFICATIONS
TRANSMISSION
ItemsNm {kgf
m}
Under cover mounting bolt6.9 {0.7}
Interlock plate bolt30 {3.1}
Clutch housing-transmission case mounting bolt44 {4.5}
Clutch release bearing retainer mounting bolt9.8 {1.0}
Control housing mounting bolt18 {1.9}
Shift cable bracket mounting bolt18 {1.9}
Speedometer gear mounting bolt3.9 {0.4}
Stopper bracket mounting bolt18 {1.9}
Select lever mounting bolt18 {1.9}
Select lever mounting nut11 {1.2}
Center differential drive gear mounting bolt132 {13.5}
Back-up lamp switch32 {3.3}
Poppet spring plug32 {3.3}
Reverse idler gear shaft mounting bolt48 {4.9}
Roll stopper bracket mounting bolt69 {7.0}

Torque Specifications /
Special toolsMANUAL TRANSMISSION OVERHAUL – 22B-10
TRANSFER
ItemsNm {kgf
m}
Transfer cover mounting bolt23 {2.4}
Transmission-transfer mounting bolt69 {7.0}
SPECIAL TOOLS
ToolNumberNameUse
MB990887Arm bushing
remover & installer
ringInstallation of transfer oil seal
MB990891Bushing remover &
installer baseInstallation of transfer oil seal
MB990928Installer adapterInstallation of input shaft oil seal
MB990932Installer adapterRemoval of differential case taper roller bearing
MB990933Installer adapterInstallation of transfer oil seal
MB990935Installer adapterInstallation of output shaft front taper roller
bearing outer race
MB990937Installer adapterInstallation of differential case taper roller
bearing

MANUAL TRANSMISSION OVERHAUL – Special Tools22B-11
Tool UseName Number
MB990938HandleUse with Installer adapter
MB991445Bushing remover
and installer baseInstallation of differential case taper roller
bearing outer race
MD998304Oil seal installerInstallation of transfer extension housing oil
seal
MD998364Camshaft oil seal
installerInstallation of gear, bearing and sleeve
MD998800Oil seal installerInstallation of differential oil seal and transfer
cover oil seal
MD998801Bearing removerInstallation and removal of gear, bearing and
sleeve
MD998812Installer capUse with Installer and installer adapter
MD998813Installer-100Use with Installer cap and installer adapter
MD998814Installer-200Use with Installer cap and installer adapter

MANUAL TRANSMISSION OVERHAUL – Special Tools22B-12
Tool UseName Number
MD998818Installer adapter
(38)Installation of input shaft front bearing
MD998819Installer adapter
(40)Installation of input shaft rear bearing and
output shaft taper roller bearing
MD998820Installer adapter
(42)Installation of reverse gear bearing sleeve
MD998821Installer adapter
(44)Installation of 4th speed gear, 5th speed gear
sleeve and 5th-reverse speed synchronizer
hub
MD998824Installer adapter
(50)Installation of 1st-2nd speed synchronizer hub,
2nd speed gear sleeve and 3rd speed gear
MD998825Installer adapter
(52)Installation of 1st speed gear sleeve, 3rd-4th
speed synchronizer hub, 4th speed gear
sleeve, 5th speed gear and thrust plate stopper
MD998917Bearing removerRemoval and installation of gear, bearing and
sleeve
MD999566ClawRemoval of taper roller bearing outer race