brake MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

00
11
12
13
14
15
16
17
21
22
26
27
32
33
34
35
36
37
42
51
54
General . . . . . . . . . . . . . . . . . . . . . . . .
Engine . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Lubrication . . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Cooling . . . . . . . . . . . . . . . . .
Intake and Exhaust . . . . . . . . . . . .
Engine Electrical . . . . . . . . . . . . . . .
Engine and Emission Control . . . .
Clutch . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Transmission . . . . . . . . . . .
Front Axle . . . . . . . . . . . . . . . . . . . . . .
Rear Axle . . . . . . . . . . . . . . . . . . . . . .
Power Plant Mount . . . . . . . . . . . . . .
Front Suspension . . . . . . . . . . . . . . .
Rear Suspension . . . . . . . . . . . . . . .
Service Brakes . . . . . . . . . . . . . . . . .
Parking Brakes . . . . . . . . . . . . . . . . .
Steering . . . . . . . . . . . . . . . . . . . . . . . .
Body . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Electrical . . . . . . . . . . . . . .
Electrical Wiring . . . . . . . . . . . . . . . .
WORKSHOP MANUAL
FOREWORD
This Workshop Manual contains procedures for
service mechanics, including removal, disassembly,
inspection, adjustment, reassembly and
installation. Figures taken from registration
documents are given in metric units only. All other
figures are given in SI units with metric units in
brackets. Use the following manuals in combination
with this manual as required.
TECHNICAL INFORMATION MANUAL
N9806CNCP9
All information, illustrations and product
descriptions contained in this manual are current
as at the time of publication. We, however, reserve
the right to make changes at any time without prior
notice or obligation.
July 1998
EVOLUTION-IV
EVOLUTION-V

ENGINE – Cylinder Head Gasket11-17
CYLINDER HEAD GASKET
REMOVAL AND INSTALLATION
Pre-removal Operation
(1) Fuel Discharge Prevention
(2) Engine Oil Removal
(3) Strut Tower Bar Removal
(4) Timing Belt Removal (Refer to P.11-21.)
(5) Thermostat Case Assembly Removal
(Refer to GROUP 14 – Water Hose Pipe.)
(6) Front Exhaust Pipe Removal (Refer to GROUP 15.)Post-installation Operation
(1) Front Exhaust Pipe Installation
(Refer to GROUP 15.)
(2) Thermostat Case Assembly Installation
(Refer to GROUP 14 – Water Hose Pipe.)
(3) Engine Oil Filling
(4) Timing Belt Installation (Refer to P.11-21.)
(5) Strut Tower Bar Installation
(6) Accelerator Cable Adjustment
O-ringDelivery pipe
Engine oil
12 – 15 {1.2 – 1.5}
5
9 {0.9}5 {0.5} 3 {0.3} 10 {1.0}
19
14
153
16
18
10
17
8
9
8
11
8
7
201
2
Unit: Nm {kgf
m}
18
6
3
13
12 4
Removal steps
1. Center cover
2. Accelerator cable connection
3. Ignition coil connector
4. Ignition coil
5. Crank angle sensor connector
6. Crank angle sensor bracket con-
nection
7. Brake booster vacuum hose con-
nection
8. Vacuum hose connection
9. TPS connector
10. ISC motor connector11. Water hose connection
12. Oxygen sensor connector
13. Injector connector
14. Cam position sensor connector
15. Coolant temperature sensor con-
nector
16. Water temperature gauge unit con-
nector
17. Control harness
D18. Fuel pipe pressure hose connection
19. Fuel return hose connection
20. Oil level gauge guide assembly

ENGINE – Engine Assembly 11- 32
ENGINE ASSEMBLY
REMOVAL AND INSTALLATION
Pre-removal Operation
(1) Fuel Discharge Prevention
(2) Hood Removal
(3) Strut Tower Bar Removal
(4) Air Hose C Removal
(Refer to GROUP 15 – Intercooler.)
(5) Radiator Assembly Removal (Refer to GROUP 14.)
(6) Under Cover Removal
(7) Front Exhaust Pipe Removal (Refer to GROUP 15.)Post-installation Operation
(1) Front Exhaust Pipe Installation
(Refer to GROUP 15.)
(2) Under Cover Installation
(3) Radiator Assembly Installation (Refer to GROUP 14.)
(4) Accelerator Cable Adjustment
(5) Air Hose C Installation (Refer to GROUP 15 – Intercooler.)
(6) Strut Tower Bar Installation
(7) Hood Installation
O-ring Delivery pipe
1
2
3
4
5
6
7 8
9
10
11
18 12
Engine oil
5 {0.5}
Unit: Nm {kgf

m}
10 – 12
{1.0 – 1.2}
17 1614 13
10
– 12
{1.0 – 1.2}
15
3 {0.3}
17
8
Removal steps1. Center cover
2. Accelerator cable
3. Brake booster vacuum hose connection
4. Vacuum hose connection
5. Throttle position sensor connector
6. Idle speed control motor connector
7. Heater hose connection
8. Ignition coil connector
9. Crank angle sensor connector
10. Oxygen sensor connector 11. Injector connector
12. Cam position sensor connector
13. Coolant temperature sensor con-
nector
14. Coolant temperature gauge unit connector
15. Vacuum pipe/hose assembly
16. Control harness
 C 17. High-pressure fuel hose connection
18. Fuel return hose connection

MPI – Troubleshooting13-16
Code No. 64 Alternator FR Terminal SystemProbable cause
Range of Check
Engine speed is approximately 50 r/min or more.
Set conditions
Input voltage at the alternator FR terminal is 4.5 V or more for 20 seconds.Open circuit in alternator FR terminal circuit
Malfunction of the engine-ECU.
OK
Replace the alternator.
NG
Check the harness wire between
the engine-ECU and alternator
connector.NG
Repair
OK
Check trouble symptom.
Measure at the alternator connec-
tor
Connect the connector.
(Use test harness MB991519.)
Voltage between 4 (blue clip)
and earth
(Engine: Idling)
(Radiator fan: Stopped)
(Headlamp: OFF → ON)
(Brake lamp: OFF → ON)
(Rear defogger switch: OFF
→ ON)
OK:Voltage drops by 0.2 to
3.5 V.NGMeasure at the alternator connec-
tor A-05.
Disconnect the connector, and
measure at the harness side.
Voltage between 4 and earth
(Ignition switch: ON)
OK:4.8 – 5.2 VNGCheck the following connec-
tors:
B-60, A-88NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between
the engine-ECU and alternator
connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check the following connector:
A-05NG
Repair
OK
Replace the engine-ECU.

MPI – Troubleshooting13-23
Terminal
No.Normal condition Check condition (Engine condition) Check item
21Fan motor relay (LOW)Fan not operating (coolant temperature: 90C or
below)Battery voltage
Fan at low speed (coolant temperature: 90 – 100C)0 – 3 V
22A/C relayEngine: Idling
A/C switch: OFF to ON (Compressor is being
driven.)Battery voltage, or 6 V
or more instanta-
neously to 0 – 3 V
33Alternator G terminalEngine: Warm, idle (radiator fan: OFF)
Headlamp: OFF to ON
Brake lamp: OFF to ON
Rear defogger switch: OFF to ONVoltage rises by 0.2 –
3.5 V.
36Engine warning lampIgnition switch: OFF → ON0 – 3 V → Battery
voltage (After several
seconds have
elapsed)
37Power steering fluid
pressure switchEngine: Idling after
warming upWhen steering wheel is
stationaryBattery voltage
When steering wheel is
turned0 – 3 V
38Control relayIgnition switch: OFFBattery voltage
Ignition switch: ON0 – 3 V
39Fuel pump relay No.2While engine is idling, suddenly depress the
accelerator pedal.Momentarily rises
slightly from 0 to 3 V.
40Exhaust temperature
warning lampIgnition switch: OFF to ON0 – 3 V to battery
voltage (After several
seconds have
elapsed)
41Alternator FR terminalEngine: Warm, idle (radiator fan: OFF)
Headlamp: OFF to ON
Brake lamp: OFF to ON
Rear defogger switch: OFF to ONVoltage drops by 0.2 –
3.5 V.
45A/C switchEngine: Idle speedTurn the A/C switch OFF0 – 3 V
Turn the A/C switch ON
(A/C compressor is oper-
ating)Battery voltage
60Oxygen sensor heater
(Evolution V only)
Engine: Idling0 – 3 V
(Evolution-V only)
Engine speed: 5,000 r/minBattery voltage
71Ignition switch-STEngine: Cranking8 V or more

INTAKE AND EXHAUST – Intake Manifold15-9
INTAKE MANIFOLD
REMOVAL AND INSTALLATION
Pre-removal Operation
(1) Fuel Discharge Prevention
(2) Throttle Body Removal (Refer to GROUP 13.)
(3) Front Exhaust Pipe Removal (Refer to P.15-14.)
(4) Air Control Valve Bracket Removal (Refer to P.15-8.)
(5) Strut Tower Bar RemovalPost-installation Operation
(1) Strut Tower Bar Installation
(2) Air Control Valve Bracket Installation
(Refer to P.15-8.)
(3) Front Exhaust Pipe Installation (Refer to P.15-14.)
(4) Throttle Body Installation (Refer to GROUP 13.)
O-ring
Unit: Nm {kgf
m}
15
Engine oil
3 {0.3} 10 – 13 {1.0 – 1.3}
10 – 12
{1.0 – 1.2}
12 – 15 {1.2 – 1.5}
35 {3.6}
9 {0.9}30 {3.1}35 {3.6}20 {2.0}22 {2.2}20 {2.0}
14 14
167
5
17
1521
3
4 6
7 7
19
20
18 8
9 12
1011
13
Removal steps
1. Center cover
2. Ignition coil connector connection
3. Oxygen sensor connector connec-
tion
4. Crank angle sensor connector con-
nection
5. Injector connector connection
6. PCV hose
7. Vacuum hose connection
8. Brake booster vacuum hose con-
nection
9. Vacuum tank, solenoid valve, and
vacuum hose assembly10. Intake manifold stay
11. Oil level gauge guide assembly
12. Vacuum hose and pipe mounting
bolt
13. Fuel return hose connection
A14. Fuel high pressure hose connection
A15. Delivery pipe, injector, and pres-
sure regulator assembly
16. Insulator
17. Insulator
18. Alternator brace stay
19. Intake manifold
20. Intake manifold gasket

CLUTCH –
Service Specifications /
Lubricants / On-vehicle Service21-2
SERVICE SPECIFICATIONS
ItemsStandard value
Clutch pedal height mm162.5 – 165.5
Clutch pedal clevis pin play mm1 – 3
Clutch pedal free play mm6 – 13
Distance between the clutch pedal and the toeboard when the clutch is disengaged mm70 or more
LUBRICANTS
ItemsSpecified lubricantsQuantity
Clutch fluidMITSUBISHI genuine brake fluid “DIA-QUEEN
BRAKE FLUID SUPER 4”As required
Push rod assemblyRubber grease
Boot
Release cylinder push rodMOLYKOT BR-2 PUS
ON-VEHICLE SERVICE
1. CLUTCH PEDAL INSPECTION AND
ADJUSTMENT
(1) Turn up the carpet, etc. under the clutch pedal.
(2) Measure the clutch pedal height.
Standard value (A): 162.5 – 165.5 mm
(3) If the height of the clutch pedal is outside the standard
value, loosen the lock nut and adjust the pedal height
to the standard value using the adjusting bolt.
Clutch pedal height
A
Setting nutAdjusting bolt
Locking
nut
13 {1.3}
6 {0.6}

CLUTCH – On-vehicle Service21-3
(4) Measure the clutch pedal play.
Standard value (B): 1 – 3 mm
(5) If the clutch pedal play is not within the standard value,
loosen the setting nut and move the push rod to adjust.
Caution
Do not push in the master cylinder push rod at this
time.
(6) After completing the adjustments, confirm that the clutch
pedal free play (measured at the face of the pedal pad)
and the distance between the clutch pedal (the face of
the pedal pad) and the toeboard when the clutch is
disengaged are within the standard value ranges.
Standard value (C): 6 – 13 mm
Standard value (D): 70 mm or more
(7) If the clutch pedal free play and the distance between
the clutch pedal and the toeboard when the clutch is
disengaged do not agree with the standard values, it
is probably the result of either air in the hydraulic system
or a faulty master cylinder or clutch. Bleed the air, or
disassemble and inspect the master cylinder, release
cylinder or clutch.
(8) Turn back the carpet, etc.
2. BLEEDING
Specified fluid:
MITSUBISHI genuine brake fluid “DIA-QUEEN BRAKE
FLUID SUPER 4”
Caution
Use the specified brake fluid. Avoid using a mixture of
the specified fluid and other fluid.
Clutch pedal clevis pin play
B
Clutch pedal free
playDistance between the
clutch pedal and the
toeboard when the
clutch is disengaged
CD

CLUTCH – Clutch Control21-6
CLUTCH MASTER CYLINDER
DISASSEMBLY AND REASSEMBLY
6 7
4
1
3
Piston repair kitClutch fluid:
DIA-QUEEN BRAKE
FLUID SUPER 4
Grease: Rubber grease
5
2
21422 8
3
Unit: Nm {kgf
m}
13 {1.3}
Disassembly steps
1. Piston stopper ring
2. Piston assembly
3. Push rod assembly
4. Boot
5. Reservoir cap
6. Spring pin
7. Reservoir tank
8. Clutch master cylinder bodyCaution
Do not disassemble piston assembly.

MANUAL TRANSMISSION – Transmission Assembly22A-8
16 18
Unit: Nm {kgfm}
52 {5.3}*
19
17
9
10
12
1315
1214
69 {7.0} 69 {7.0} 15 – 33
{1.5 – 3.4} 39 {4.0}59 – 71
{6.0 – 7.2} 26 – 33
{2.7 – 3.4}48 {4.9}
52 {5.3}*
Lifting up of the vehicle
9. Stabilizer bar connection
10. Wheel speed sensor cable connec-
tion
11. Brake hose clamp
12. Tie rod end connection
13. Lower arm ball joint connection
A
Clutch release bearing connection
14. Centermember assembly
B15. Drive shaft connection
B16. Drive shaft connection

Strut assembly
(Refer to GROUP 33A.)C17. Output shaft

Air hose A
(Refer to GROUP 15 – Intercooler.)
18. Transmission assembly lower part
coupling bolts
19. Transmission assembly
Caution
Mounting locations marked by * should be
provisionally tightened, and then fully tightened
when the body is supporting the full weight of the
engine.