camshaft MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

11-1
ENGINE
CONTENTS
SERVICE SPECIFICATIONS 2. . . . . . . . . . . . . .
SEALANTS 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 2 . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE ADJUSTMENTS 4 . . . . . . . . . . . . . . . . .
1. Drive Belt Tension Check 4 . . . . . . . . . . . . . . .
2. Auto Tensioner Check 5 . . . . . . . . . . . . . . . . . . .
3. Lash Adjuster Check 5 . . . . . . . . . . . . . . . . . . . .
4. Lash Adjuster Replacement 7 . . . . . . . . . . . . . .
5. Ignition Timing Check 7 . . . . . . . . . . . . . . . . . . .
6. Idle Speed Check and Idle Mixture Check 7
7. Compression Pressure Check 7 . . . . . . . . . . . .
8. Manifold Vacuum Check 8 . . . . . . . . . . . . . . . . .
CRANKSHAFT PULLEY 9. . . . . . . . . . . . . . . . . .
CAMSHAFT AND CAMSHAFT
OIL SEAL 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OIL PAN 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRANKSHAFT OIL SEAL 15 . . . . . . . . . . . . . .
CYLINDER HEAD GASKET 17 . . . . . . . . . . . .
TIMING BE LT . . . . . . . . . . . . . . 21 . . . .
ENGINE ASSEMB LY 32
. . . . . . . . . . . . . . . . . . .

ENGINE – Service Specifications / Sealants / Special Tools11-2
SERVICE SPECIFICATIONS
ItemsStandard valueLimit
Basic ignition timing5
BTDC ± 3
–
Ignition timing (at idle)Approx. 5
BTDC–
Idle speed rpm850 ± 50–
CO contents %0.6 or less–
HC contents ppm300 or less–
Compression pressure kg/cm2 – rpm11.5 – 250Min. 9.7 – 250
Compression pressure difference of all cylinders kg/cm2–Max. 1.0
Intake manifold vacuum kPa {mmHg}–Min. 55 {410}
Cylinder head bolt shank length mm–99.4
SEALANTS
ItemsSpecified sealants
Rocker coverSemi-drying sealant: THREEBOND 1207D [MZ 100168] (containing 150 g)
Oil panSemi-drying sealant: THREEBOND 1207F [MZ 100191] (containing 150 g)
NOTE:
Given in [ ] are MITSUBISHI GENUINE PART numbers.
SPECIAL TOOLS
ToolNumberNameUse
MD998782Valve lifter setReplacing the lash adjuster
MB990767End yoke holderHolding the crankshaft pulley
Holding the camshaft sprocket

ENGINE – Special Tools11-3
Tool UseName Number
MD998719Crankshaft pulley
holder pinHolding the crankshaft pulley
Holding the camshaft sprocket
MD998715Pulley holder pin
MD998713Camshaft oil seal
installerPressfitting the camshaft oil seal
MD998727Oil pan removerRemoving the oil pan
MD998781Flywheel stopperSecuring the flywheel or drive plate
MD998776Crankshaft rear oil
seal installerPressfitting the crankshaft rear oil seal
MB990938Handle
MD998382Crankshaft front oil
seal installerInstalling the crankshaft front oil seal
MD998285Crankshaft front oil
seal guide

ENGINE – Camshaft and Camshaft Oil Seal11-10
CAMSHAFT AND CAMSHAFT OIL SEAL
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
(1) Engine Coolant Draining and Refilling
(2) Air Hose C Removal and Installation
(Refer to GROUP 15 – Intercooler.)
(3) Spark Plug Cable and Ignition Coil Assembly Removal
and Installation(4) Air Pipe Removal and Installation
(Refer to GROUP 15 – Air Control Valve.)
(5) Timing Belt Removal and Installation
(Refer to P.11-21.)
22 {2.2}
Unit: Nm {kgf
m}
10 {1.0}9 {0.9}
3.4 {0.35}
20 {2.0}
88 {9.0} 12 – 15 {1.2 – 1.5}
1
53 4
6
2
14
15
17 16
13
12
11 10 9 8 7
Removal steps
1. Breather hose connection
2. PCV hose connection
3. Crank angle sensor bracket con-
nection
4. Control harness connection
5. Rocker cover
6. Radiator upper hose connection
7. Cover
E8. Cam position sensing cylinder9. Cam position sensor support
10. Semi-circular packing
AD11. Camshaft sprocket
C12. Camshaft oil seal
B13. Front cam cap
B14. Rear cam cap
B15. Cam cap
A16. Camshaft (exhaust side)
A17. Camshaft (intake side)

ENGINE – Camshaft and Camshaft Oil Seal11-11
Grease and adhesive application points
Timing belt side
Semi-drying sealant: THREEBOND 1207D
Lip 10 mm
10 mm10 mm
Semi-drying sealant:
THREEBOND 1207FEngine oil
Semi-drying sealant: THREEBOND 1207DTiming belt side
26
φ 3 mm
REMOVAL SERVICE POINT
ACAMSHAFT SPROCKET REMOVAL
INSTALLATION SERVICE POINTS
ACAMSHAFT INSTALLATION
(1) Apply engine oil to the cams and journals of the camshaft.
(2) Mount the camshaft on the cylinder head.
Caution
Make sure that the camshaft has a unique orientation
for installation, the intake side and exhaust side. The
exhaust camshaft has a slit in the rear end face.
MB990767
MD998719
Camshaft sprocket side
Camshaft (exhaust side)Slit

ENGINE – Camshaft and Camshaft Oil Seal11-12
BCAM CAP / REAR CAP / FRONT CAM CAP
INSTALLATION
(1) Locate the camshaft dowel pins as illustrated.
(2) Temporarily tighten cam cap in two to three steps, then
torque it to specification.
Tightening torque: 20 Nm {2.0 kgf
m}
CCAMSHAFT OIL SEAL INSTALLATION
(1) Apply engine oil to the entire periphery of the oil seal
lip.
(2) Pressfit the oil seal as shown.
DCAMSHAFT SPROCKET INSTALLATION
As you did during removal, secure the camshaft sprocket
with the special tool and tighten bolt to specification.
Tightening torque: 88 Nm {9.0 kgf
m}
ECAM POSITION SENSING CYLINDER
Install the cam position sensing cylinder so that the ID paint
on the cam position sensing cylinder is 90
with respect to
the camshaft dowel pin as shown.
Intake side Approx. 12
Dowel pin
Exhaust side
MD998713
ID paintDowel pin
90

ENGINE – Timing Belt11-21
TIMING BELT
REMOVAL AND INSTALLATION
1
2
3
4 56
7
8
910
11 1213
14 15
16 171821
22
23
242526
27
28
20
19
11 {1.1}
11 {1.1} 11 {1.1}
88 {9.0}
49 {5.0}
9 {0.9}
48 {4.9}54 {5.5}49 {5.0} 118 {12.0}
9 {0.9}3.5 {0.35}
49 {5.0}
45 {4.6}
19 {1.9}30 {3.1} 24 {2.4}24 {2.4}
Unit: Nm {kgf
m}
Removal steps
1. Front upper cover
2. Front center cover
3. Front lower cover
4. Bracket

AL
5. Timing belt
K
6. Tensioner pulley
7. Tensioner arm
J
8. Auto tensioner
9. Idle pulley
10. Crankshaft position sensor

BI
11. Oil pump sprocket

CH
12. Crankshaft bolt

D13. Crankshaft sprocket
14. Sensing blade15. Tensioner B

EG
16. Timing belt B

FF
17. Counterbalance shaft sprocket
E
18. Spacer

G19. Crankshaft sprocket B
20. Crankshaft key
D
21. Rocker cover
C
22. Semi-circular packing
B
23. Engine support bracket

HA
24. Camshaft sprocket bolt
25. Camshaft sprocket
26. Timing belt rear right cover
27. Timing belt rear left upper cover
28. Timing belt rear left lower cover

ENGINE – Timing Belt11-22
REMOVAL SERVICE POINTS

ATIMING BELT REMOVAL
(1) If the timing belt is to be reused, chalk an arrow mark
on the back surface of the belt so that the belt can be
reinstalled in the same direction.
(2) Place the exhaust camshaft sprocket in a position where
the timing mark for No. 1 cylinder is positioned about
one tooth before the top dead center of the compression
stroke.
Caution
The camshaft sprocket on the exhaust side can turn
very easily because of the valve spring tension. Use
care not to allow your fingers to get caught by the
sprocket.
(3) Loosen the lock nut of the tensioner pulley, then remove
the timing belt.

BOIL PUMP SPROCKET REMOVAL
(1) Remove the plug on the left side of cylinder block.
(2) Insert a screwdriver (shank diameter 8 mm) to block the
counterbalance shaft.
(3) Loosen the flange bolt.
(4) Remove the oil pump sprocket.

CCRANKSHAFT BOLT LOOSENING

DCRANKSHAFT SPROCKET REMOVAL
If it is difficult to remove the sprocket, use the special tool.
Timing mark

ENGINE – Timing Belt11-23

ETIMING BELT “B” REMOVAL
Make an arrow mark on the back of the timing belt indicating
the direction of rotation so it may be reassembled in the
same direction if it is to be reused.

FCOUNTERBALANCE SHAFT SPROCKET
REMOVAL

GCRANKSHAFT SPROCKET “B” REMOVAL
If it is difficult to remove the sprocket, use the special tool.

HCAMSHAFT SPROCKET BOLT LOOSENING
Use a wrench to hold the hexagonal part of the camshaft,
and then remove the camshaft sprocket mounting bolt.
INSPECTION
TIMING BELT
Replace belt if any of the following conditions exist.
(1) Hardening of back rubber.
Back side is glossy without resilience and leaves no indent
when pressed with fingernail.
6EN1322

ENGINE – Timing Belt11-25
INSTALLATION SERVICE POINTS
A
CAMSHAFT SPROCKET BOLT TIGHTENING
Using a wrench, hold the camshaft at its hexagon and tighten
the bolt to the specification.
Caution
Locking the camshaft sprocket with a tool damages the
sprocket.
B
ENGINE SUPPORT BRACKET LEFT
INSTALLATION
Coat the bolts illustrated with sealant before tightening.
Specified sealant: THREEBOND 1207F or equivalent
C
SEALANT APPLICATION ON SEMI-CIRCULAR
PACKING
Apply sealant to the areas indicated in the illustration.
Specified sealant: THREEBOND 1212D or equivalent
Apply sealant
Apply
sealant 10 mm
10 mm
Cylinder head Semi-circular
packing