coolant temperature MITSUBISHI LANCER EVOLUTION VI 1999 Owner's Manual

MPI – Troubleshooting13-52
INSPECTION PROCEDURE 44
MUT-II: Check if surge occurs.
MUT-II Data list
26 Idle position switch (Refer to P.13-58.)NGCheck the idle position switch system.
(Refer to P.13-38, INSPECTION PROCEDURE 26.)
OK
MUT-II Data list
13 Intake air temperature sensor (Refer to P.13-56.)NGCheck the intake air temperature sensor system. (Refer to P.13-9,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 13.)
OK
MUT-II Data list
25 Barometric pressure sensor (Refer to P.13-58.)NGCheck the barometric pressure sensor system. (Refer to P.13-14,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 25.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13-10, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
14 Throttle position sensor (Refer to P.13-57.)NGCheck the throttle position sensor system. (Refer to P.13-9, IN-
SPECTION PROCEDURE FOR DIAGNOSIS CODE 14.)
OK
MUT-II Data list
11 Oxygen sensor
OK:600–1,000 mV during sudden racingNGCheck the oxygen sensor system.
(Refer to P.13-42, INSPECTION PROCEDURE 31.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Changes between 0–400 mV and 600–1,000 mV during
idlingNGCheck the fuel pressure. (Refer to P.13-30.)*
1. Inspect the intake of air into the air intake system

Broken intake manifold gasket

Broken vacuum hose

PCV valve does not operate.

Broken air intake hose
2. Check the injector for clog.OK
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).

MPI – Troubleshooting13-56
DATA LIST REFERENCE TABLE
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
11Oxygen
sensorEngine:After having
warmed up
Air/fuel mixture is
made leaner when de-
When at 4,000 r/min,
engine is suddenly
decelerated200 mV or lessProcedure
No. 3113-42
made leaner when de-
celerating, and is made
richer when racing.
When engine is
suddenly raced600 – 1,000 mV
Engine:After having
warmed up
The oxygen sensor
si
gnal is used to check
Engine is idling400 mV or less
(Changes)
signal is used to check
the air/fuel mixture
ratio, and control
condition is also
checked by the ECU.2,500 r/min600 – 1,000 mV
12Air flow
sensor*
Engine coolant
tem
perature: 80 –
Engine is idling17 – 43 Hz––
sensor
TION-IV>temperature: 80
95C

Lamps, electric
li f d ll
2,500 r/min46 – 86 Hzp
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T:
P range)Engine is racedFrequency
increases in
response to
racing
12Air flow
sensor*
Engine coolant
tem
perature: 80 –
Engine is idling12 – 38 Hz––
sensor
TION-V, VI>temperature: 80
95C

Lamps, electric
li f d ll
2,500 r/min36 – 76 Hzp
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T:
P range)Engine is racedFrequency
increases in
response to
racing
13Intake air
temperature
sensor
Ignition switch: ON or
with engine runningWhen intake air
temperature is –20C–20CCode No.
1313-9
sensorWhen intake air
temperature is 0C0C
When intake air
temperature is 20C20C
When intake air
temperature is 40C40C
When intake air
temperature is 80C80C
NOTE
*: In a new vehicle [driven approximately 500 km or less], the air flow sensor output frequency is sometimes
10% higher than the standard frequency.

MPI – Troubleshooting13-57
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
14Throttle
position
Ignition switch: ONSet to idle position300 – 1,000 mVCode No.
14
13-9
position
sensor
Gradually openIncreases in
proportion to
throttle opening
angle
14
Open fully4,500 – 5,500 mV
16Power
supply
voltageIgnition switch: ONSystem voltageProcedure
No. 2413-35
18Cranking
signal Ignition switch: ONEngine: StoppedOFFProcedure
No. 2713-38
g
(ignition
switch-ST)Engine: CrankingON
21Engine
coolant
temperature
sensor
Ignition switch: ON or
with engine runningWhen engine
coolant temperature
is –20C–20CCode No.
2113-10
sensor
When engine
coolant temperature
is 0C0C
When engine
coolant temperature
is 20C20C
When engine
coolant temperature
is 40C40C
When engine
coolant temperature
is 80C80C

MPI – Troubleshooting13-58
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
22Crank angle
sensor
Engine: Cranking

Tachometer:
ConnectedCompare the engine
speed readings on
the tachometer and
the MUT-II.Accord––

Engine: Idling

Idle position
switch: ONWhen engine
coolant temperature
is –20C1,300 – 1,500 rpm
When engine
coolant temperature
is 0C1,300 – 1,500 rpm
When engine
coolant temperature
is 20C1,300 – 1,500 rpm
When engine
coolant temperature
is 40C1,150 – 1,350 rpm
When engine
coolant temperature
is 80C750 – 950 rpm
25Barometric
pressure
Ignition switch: ONAt altitude of 0 m101 kPaCode No.
25
13-14
pressure
sensor
At altitude of 600 m95 kPa
25
At altitude of 1,200 m88 kPa
At altitude of 1,800 m81 kPa
26Idle position
switchIgnition switch: ON
Check by operating
accelerator pedal
Throttle valve:
Set to idle positionONProcedure
No. 2613-38
accelerator pedal
repeatedly.)Throttle valve:
Slightly openOFF*
27Power
steering fluid
pressure
Engine: IdlingSteering wheel
stationaryOFFProcedure
No. 2813-39
pressure
switchSteering wheel
turningON
28A/C switchEngine: Idling
(when A/C switch isA/C switch: OFFOFFProcedure
No. 2913-39
(Ctc
ON, A/C compressor
should be operating.)A/C switch: ONON
NOTE
*: The idle position switch normally turns off when the voltage of the throttle position sensor is 50 –
100 mV higher than the voltage at the idle position. If the throttle position switch turns back on
after the throttle valve has opened, the idle position switch and the throttle position sensor need
to be adjusted.

MPI – Troubleshooting13-59
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
41Injectors*1
TION-IV>Engine: CrankingWhen engine
coolant temperature
is 0C (injection is
carried out for all
cylinders
simultaneously)27 – 41 ms––
When engine
coolant temperature
is 20C14 – 22 ms
When engine
coolant temperature
is 80C3.9 – 5.9 ms
Injectors*2
TION-IV>

Engine coolant
temperature:
80–95C
Engine is idling1.2 – 2.4 ms
TION-IV>80–95C

Lamps, electric
cooling fan and all
accessories: OFF
2,500 r/min1.0 – 2.2 ms
accessories: OFF

Transmission:
Neutral (A/T :
P range)When engine is
suddenly racedIncreases
41Injectors*1
TION-V, VI>Engine: CrankingWhen engine
coolant temperature
is 0C27 – 40 ms––
When engine
coolant temperature
is 20C14.5 – 21.7 ms
When engine
coolant temperature
is 80C3.8 – 5.6 ms
Injectors*2
TION-V VI>

Engine coolant
temperature:
80–95C
Engine is idling0.9 – 2.1 ms
TION-V, VI>80–95C

Lamps, electric
cooling fan and all
accessories: OFF
2,500 r/min0.7 – 1.9 ms
accessories: OFF

Transmission:
Neutral (A/T :
P range)When engine is
suddenly racedIncreases
NOTE
*1: The injector drive time represents the time when the cranking speed is at 250 r/min or below when
the power supply voltage is 11 V.
*
2: In a new vehicle [driven approximately 500 km or less], the injector drive time is sometimes 10%
longer than the standard time.

MPI – Troubleshooting13-60
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
44Ignition coils
and power
transistors
having warmed up

Timing lamp is set.
(The timing lampEngine is idling3ATDC –
13BTDC––
TION-IV>
(tgp
is set in order to
check actual
ignition timing.)2,500 r/min24 – 44BTDC
44Ignition coils
and power
transistors

Engine: After
having warmed up

Timing lamp is set
Engine is idling0 – 13BTDC––
transistors
TION-V, VI>
Timing lamp is set.
2,500 r/min24 – 44BTDC
45ISC
(stepper)
motor
position *

Engine coolant
temperature: 80 –
90C

Lam
ps, electric
A/C switch: OFF2 – 25 steps––
position
Lamps, electric
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T :
P range)
Idl iti
A/C switch:
OFF → ONIncreases by
10 – 70 steps
g)

Idle position
switch: ON

Engine: Idling

When A/C switch
is ON, A/C
compressor should
be operating
A/C switch: OFF

Select lever:
N range →
D rangeIncreases by
5 – 50 steps
49A/C relayEngine: After having
warmed up/Engine is
idlingA/C switch: OFFOFF (Compressor
clutch is not
operating)Procedure
No. 2913-39
A/C switch: ONON (Compressor
clutch is
operating)
NOTE
*: In a new vehicle [driven approximately 500 km or less], the stepper motor has sometimes 30 steps
greater than the standard value.
Caution
When shifting the select lever to D range, the brakes should be applied so that the vehicle does
not move forward.

MPI – Troubleshooting13-63
ENGINE-ECU INSPECTION
TERMINAL VOLTAGES
Engine ECU connector
Terminal
No.Check itemCheck condition (Engine condition)Normal condition
1No.1 injectorWhile engine is idling after having been warmed up,
suddenly depress the accelerator pedal
Momentarily drops
slightlyfrom 1114V
14No.2 injector
suddenly depress the accelerator pedal.slightly from 11 – 14 V.
2No.3 injector
15No.4 injector
3Fuel pressure control
valve
Ignition switch: ONSystem voltage
valve
Engine: Cranking to idling (within about two minutes)0 – 3 V to sytem
voltage
4Stepper motor coil (A1)Engine: Immediately after engine has been started
f
or warming up
Changes repeatedly
f
rom system voltage
17Stepper motor coil (A2)
for warming upfrom system voltage
to 0 – 6 V and from 0
6 V to system5Stepper motor coil (B1)– 6 V to system
voltage.
18Stepper motor coil (B2)
6Secondary air control
solenoid valveIgnition switch: ONSystem voltage
8Fuel pump relayIgnition switch: ONSystem voltage
Engine: Idling0 – 3 V
10Power transistor unit
(A)Engine speed: 3,000 r/min0.3 – 3.0 V
23Power transistor unit
(B)
11Wastegate solenoid
valve
Ignition switch: ONSystem voltage
valve
Engine: At idle after having been warmed up (when
premium gasoline is used)0 – 3 V
12Power supplyIgnition switch: ONSystem voltage
25
19Air flow sensor reset
signal
Engine: Idling0 – 1 V
signal
Engine speed: 3,000 r/min6 – 9 V
20Fan motor relay (HI)
Fan not operating (coolant temperature: 90C or
below)System voltage
Fan at high speed (coolant temperature: 105C or
above)0 – 3 V

MPI – Troubleshooting13-64
Terminal
No.Normal condition Check condition (Engine condition) Check item
20Radiator fan motor
relay (HI)

Radiator fan not operating (coolant temperature:
95C or below)System voltage
Radiator fan at high speed (coolant temperature:
105C or above)0 – 3 V
21Fan motor relay (LOW)
Fan not operating (coolant temperature: 95C or
below)System voltage
Fan at low speed (coolant temperature: 95 – 100C)0 – 3 V
21Radiator fan motor
relay (LOW)

Radiator fan not operating (coolant temperature:
95C or below)System voltage
Radiator fan at low speed (coolant temperature: 95
– 105C)0 – 3 V
22A/C relay
Engine: Idling

A/C switch: OFF to ON (Compressor is being
driven.)System voltage, or 6
V or more instanta-
neously to 0 – 3 V
32A/C condenser fan
motor relay (HI)

A/C condenser fan not operating (A/C switch: ON,
coolant temperature: 105C or below)System voltage
A/C condenser fan at high speed (A/C switch: ON,
coolant temperature: 105C or above)0 – 3 V
33Alternator G terminal
Engine: Warm, idle (radiator fan: OFF)

Headlamp: OFF to ON

Brake lamp: OFF to ON

Rear defogger switch: OFF to ONVoltage rises by 0.2 –
3.5 V.
34A/C condenser fan
motor relay (LOW)

A/C condenser fan not operating (A/C switch: OFF,
coolant temperature: 105C or below)System voltage
A/C condenser fan at low speed (A/C switch: OFF,
coolant temperature: 105C or above)0 – 3 V
36Engine warning lampIgnition switch: OFF → ON0 – 3 V → System
voltage (After several
seconds have
elapsed)
37Power steering fluid
pressure switchEngine: Idling after
warming upWhen steering wheel is
stationarySystem voltage
When steering wheel is
turned0 – 3 V
38Control relayIgnition switch: OFFSystem voltage
Ignition switch: ON0 – 3 V
39Fuel pump relay No.2While engine is idling, suddenly depress the
accelerator pedal.Momentarily rises
slightly from 0 to 3 V.
40Exhaust temperature
warning lampIgnition switch: OFF to ON0 – 3 V to system
voltage (After several
seconds have
elapsed)

MPI – Troubleshooting13-65
Terminal
No.Normal condition Check condition (Engine condition) Check item
41Alternator FR terminal
Engine: Warm, idle (radiator fan: OFF)

Headlamp: OFF to ON

Brake lamp: OFF to ON

Rear defogger switch: OFF to ONVoltage drops by 0.2 –
3.5 V.
45A/C switchEngine: Idle speedTurn the A/C switch OFF0 – 3 V
Turn the A/C switch ON
(A/C compressor is oper-
ating)System voltage
60Oxygen sensor heater

Engine: Idling0 – 3 V

Engine speed: 5,000 r/minSystem voltage
71Ignition switch-STEngine: Cranking8 V or more
72Intake air temperature
sensorIgnition switch: ONWhen intake air tempera-
ture is 0C3.2 – 3.8 V
When intake air tempera-
ture is 20C2.3 – 2.9 V
When intake air tempera-
ture is 40C1.5 – 2.1 V
When intake air tempera-
ture is 80C0.4 – 1.0 V
76Oxygen sensorEngine: Running at 2,000 r/min after having been
warmed up (Check using a digital type voltmeter)0 ↔ 0.8 V
(Changes repeatedly)
80Backup power supplyIgnition switch: OFFSystem voltage
81Sensor impressed
voltageIgnition switch: ON4.5 – 5.5 V
82Ignition switch-IGIgnition switch: ONSystem voltage
83Engine coolant
temperature sensorIgnition switch: ONWhen engine coolant
temperature is 0C3.2 – 3.8 V
When engine coolant
temperature is 20C2.3 – 2.9 V
When engine coolant
temperature is 40C1.3 – 1.9 V
When engine coolant
temperature is 80C0.3 – 0.9 V
84Throttle position sensorIgnition switch: ONSet throttle valve to idle
position0.3 – 1.0 V
Fully open throttle valve4.5 – 5.5 V
85Barometric pressure
sensor
Ignition switch: ONWhen altitude is 0 m3.7 – 4.3 V
sensor
When altitude is 1,200 m3.2 – 3.8 V
86Vehicle speed sensor
Ignition switch: ON

Move the vehicle slowly forward0 ↔ 5 V
(Changes repeatedly)

MPI – Troubleshooting13-67
RESISTANCE AND CONTINUITY BETWEEN HARNESS SIDE CONNECTORS AND TERMINALS
Engine-ECU Harness Side Connector Terminal Arrangement
Terminal No.Inspection itemNormal condition (Check condition)
1 – 12No.1 injector2 – 3 Ω (At 20C)
14 – 12No.2 injector
2 – 12No.3 injector
15 – 12No.4 injector
3 – 12Fuel pressure control valve28 – 36 Ω (At 20C)
4 – 12Stepper motor coil (A1)28 – 33 Ω (At 20C)
17 – 12Stepper motor coil (A2)
5 – 12Stepper motor coil (B1)
18 – 12Stepper motor coil (B2)
6 – 12Secondary air control solenoid valve28 – 36 Ω (At 20C)
11 – 12Wastegate solenoid valve62 – 74 Ω (At 20C)
60 – 12Oxygen sensor heater
11 – 18 Ω (at 20C)
13 – Body earthEngine-ECU earthContinuity established (0 Ω)
26 – Body earth
72 – 92Intake air temperature sensor5.3 – 6.7 kΩ (When intake air temperature is 0C)
2.3 – 3.0 kΩ (When intake air temperature is 20C)
1.0 – 1.5 kΩ (When intake air temperature is 40C)
0.30 – 0.42 kΩ (When intake air temperature is 80C)
74 – 77High temperature sensor3 Ω or less
83 – 92Engine coolant temperature sensor5.1 – 6.5 kΩ (When coolant temperature is 0C)
2.1 – 2.7 kΩ (When coolant temperature is 20C)
0.9 – 1.3 kΩ (When coolant temperature is 40C)
0.26 – 0.36 kΩ (When coolant temperature is 80C)
87 – 92Idle position switchContinuity established (when throttle valve is at idle
position)
No continuity (when throttle valve is slightly open)
91 – Body earth–Continuity established