clutch MITSUBISHI LANCER EVOLUTION VI 1999 Workshop Manual

00
11
13
21
22
26
27
33
35
37
42
51
52
54
55
General . . . . . . . . . . . . . . . . . . . . . . . .
Engine . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Transmission . . . . . . . . . . .
Front Axle . . . . . . . . . . . . . . . . . . . . . .
Rear Axle . . . . . . . . . . . . . . . . . . . . . .
Front Suspension . . . . . . . . . . . . . . .
Service Brakes . . . . . . . . . . . . . . . . .
Steering . . . . . . . . . . . . . . . . . . . . . . . .
Body . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Electrical . . . . . . . . . . . . . .
Electrical Wiring . . . . . . . . . . . . . . . .
WORKSHOP MANUAL
SUPPLEMENT
FOREWORD
This Workshop Manual contains procedures for
service mechanics, including removal, disassembly,
inspection, adjustment, reassembly and
installation. Use the following manuals in
combination with this manual as required.
TECHNICAL INFORMATION MANUAL
N9806CNCP9
N9806CNCP9-A
WORKSHOP MANUAL
S9806CNCP9
All information, illustrations and product
descriptions contained in this manual are current
as at the time of publication. We, however, reserve
the right to make changes at any time without prior
notice or obligation.
The EVOLUTION -VI is sold exclusively through
RALLIART Inc. Since the EVOLUTION-VI is a rally-
based model, it will not be warranted and will not be
homologated for general production. Therefore, any
service matters on the EVOLUTION-VI should be
inquired to RALLIART Inc. as usual.
EVOLUTION-VI

Mitsubishi Motors Corporation March 1999
Interior and Supplemental
Restraint System (SRS) . . . . . . . . .
.
Heater, Air Conditioner and
Ventilation . . . . . . . . . . . . . . . . . . . . .
.

ENGINE – Starter Motor11-83
STARTER MOTOR
DISASSEMBLY AND REASSEMBLY
1 23
4 5
6
789
10 1112 13 14
15
16 17
18 19
202122
23
Disassembly steps
1. Cover
2. Screw
A3. Magnetic switch
4. Screw
5. Through
6. Rear bracket
7. Brush holder
8. Brush
9. Rear bearing
B10. Armature
11. Yoke assembly
B12. Ball13. Packing A
14. Packing B
15. Plate
16. Planetary gear
17. Lever
CA18. Snap ring
CA19. Stop ring
20. Overrunning clutch
21. Internal gear
22. Planetary gear holder
23. Front bracket

ENGINE – Starter Motor11-84
DISASSEMBLY SERVICE POINTS
AMAGNETIC SWITCH REMOVAL
Disconnect field coil wire from “M” terminal of magnetic switch.
BARMATURE / BALL REMOVAL
Caution
When removing the armature, take care not to lose the
ball (which is used as a bearing) in the armature end.
CSNAP RING / STOP RING REMOVAL
(1) Press stop ring off snap ring with a suitable socket.
(2) Remove snap ring with snap ring pliers and then remove
stop ring and overrunning clutch.
STARTER MOTOR PARTS CLEANING
(1) Do not immerse parts in cleaning solvent. Immersing the
yoke and field coil assembly and/or armature will damage
insulation. Wipe motor assembly with a cloth only.
(2) Do not immerse drive unit in cleaning solvent. Overrunning
clutch is pre-lubricated at the factory and solvent will wash
lubrication from clutch.
(3) The drive unit may be cleaned with a brush moistened
with cleaning solvent and wiped dry with a cloth.
Magnetic
switch“S” terminal
“B” terminal
Field coil wire “M” terminal
Stop ringSocket
Pinion gear
Overrunning
clutch
Armature
Snap ring
Pinion gear
Overrunning
clutchSnap ring pliers
Armature

ENGINE – Starter Motor11-85
REASSEMBLY SERVICE POINTS
ASTOP RING / SNAP RING INSTALLATION
Using a suitable pulling tool, pull overrunnig clutch stop ring
over snap ring.
INSPECTION
COMMUTATOR CHECK
(1) Place the armature in a pair of “V” blocks and check
the runout with a dial indicator.
Standard value: 0.05 mm
Limit: 0.1 mm
(2) Measure the commutator outer diameter.
Standard value: 32.0 mm
Limit: 31.4 mm
(3) Check the undercut depth between segments.
Standard value: 0.5 mm
BRUSH HOLDER CHECK
Check the continuity between brush holder plate and brush
holder.
If there is no continuity, the brush holder is in order.
Stop ringOverrunning
clutchStop ring
Snap ring
Undercut
Segment
Mica
Brush holder

ENGINE – Starter Motor11-86
OVERRUNING CLUTCH CHECK
(1) While holding clutch housing, rotate the pinion. Drive
pinion should rotate smoothly in one direction, but should
not rotate in opposite direction. If clutch does not function
properly, replace overrunnig clutch assembly.
(2) Inspect pinion for wear or burrs. If pinion is worn or burred,
replace overrunning clutch assembly. If pinion is damaged,
also inspect ring gear for wear or burrs.
FRONT AND REAR BRACKET BUSHING CHECK
Inspect bushing for wear or burrs. If bushing is worn or burred,
replace front bracket assembly or rear bracket assembly.
BRUSH AND SPRING REPLACEMENT
(1) Brushes that are worn beyond wear limit line, or oil-soaked,
should be replaced.
(2) When replacing ground brush, slide the brush from brush
holder by prying retaining spring back.
ARMATURE TEST
ARMATURE COIL SHORT-CIRCUIT TEST
(1) Place armature in a growler.
(2) Hold a thin steel blade parallel and just above while rotating
armature slowly in growler. A shorted armature will cause
blade to vibrate and be attracted to the core. Replace
shorted armature.
ARMATURE COIL EARTH TEST
Check the insulation between each commutator segment and
armature coil core.
If there is no continuity, the insulation is in order.
Free
Lock
Wear limit line
Growler

MPI – Troubleshooting13-39
INSPECTION PROCEDURE 28
Power steering fluid pressure switch system
Probable cause
The presence or absence of power steering load is input to the engine-ECU.
The engine-ECU controls the idle speed control (ISC) servo based on this input.
Malfunction of power steering fluid pressure switch

Improper connector contact, open or short-circuited
harness wire

Malfunction of the engine-ECU
Check the power steering fluid pressure switch.NG
Replace
OK
Measure at the power steering fluid pressure switch connector
A-101.

Disconnect the connector, and measure at the harness side.

Voltage between 1 and earth (Ignition switch: ON)
OK:System voltageNGCheck the following
connectors: A-28, B-60NG
Repair
OK
Check trouble symptom.
NG
Check harness wire be-
tween engine-ECU and
power steering fluid pres-
sure switch connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check the following
connector: A-101NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
INSPECTION PROCEDURE 29
A/C switch and A/C relay system
Probable cause
When an A/C ON signal is input to the engine-ECU, the engine-ECU carries out
control of the idle speed control (ISC) servo, and also operates the A/C compressor
magnetic clutch.
Malfunction of A/C control system

Malfunction of A/C switch

Improper connector contact, open or short-circuited
harness wire

Malfunction of the engine-ECU
Check the A/C compressor relay.
(Refer to GROUP 55 – On-vehicle Service.)NG
Replace
OK
Measure at the engine-ECU connectors B-59, B-60.

Disconnect the connector, and measure at the harness side.

Voltage between 22 and earth, and 45 and earth
(Ignition switch: ON, A/C switch: ON)
OK:System voltage

Short-circuit between 22 and earth
(Ignition switch: ON, A/C switch: ON)
OK:A/C compressor clutch turns on.NGCheck the A/C system. (Refer to GROUP 55 – On-vehicle Service.)
OKCheck the following
connectors: B-59, B-60NG
Replace
OK
Check trouble symptom.
NG
Replace the engine-ECU.

MPI – Troubleshooting13-60
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
44Ignition coils
and power
transistors
having warmed up

Timing lamp is set.
(The timing lampEngine is idling3ATDC –
13BTDC––
TION-IV>
(tgp
is set in order to
check actual
ignition timing.)2,500 r/min24 – 44BTDC
44Ignition coils
and power
transistors

Engine: After
having warmed up

Timing lamp is set
Engine is idling0 – 13BTDC––
transistors
TION-V, VI>
Timing lamp is set.
2,500 r/min24 – 44BTDC
45ISC
(stepper)
motor
position *

Engine coolant
temperature: 80 –
90C

Lam
ps, electric
A/C switch: OFF2 – 25 steps––
position
Lamps, electric
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T :
P range)
Idl iti
A/C switch:
OFF → ONIncreases by
10 – 70 steps
g)

Idle position
switch: ON

Engine: Idling

When A/C switch
is ON, A/C
compressor should
be operating
A/C switch: OFF

Select lever:
N range →
D rangeIncreases by
5 – 50 steps
49A/C relayEngine: After having
warmed up/Engine is
idlingA/C switch: OFFOFF (Compressor
clutch is not
operating)Procedure
No. 2913-39
A/C switch: ONON (Compressor
clutch is
operating)
NOTE
*: In a new vehicle [driven approximately 500 km or less], the stepper motor has sometimes 30 steps
greater than the standard value.
Caution
When shifting the select lever to D range, the brakes should be applied so that the vehicle does
not move forward.

21A-1
CLUTCH
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 2. . . . . . . . . . . . . .
LUBRICANTS 2. . . . . . . . . . . . . . . . . . . . . . . . . . . ON-VEHICLE SERVICE 2. . . . . . . . . . . . . . . . . .
Clutch Pedal Inspection and Adjustment 2. . . . .
Bleeding 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH PEDAL 4. . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH CONTROL 5. . . . . . . . . . . . . . . . . . . . .
Clutch Master Cylinder 6. . . . . . . . . . . . . . . . . . . . .

CLUTCH –
General / Service Specifications /
Lubricants / On-vehicle Service21A-2
GENERAL
OUTLINE OF CHANGE

The service procedures for left-hand drive vehicles have been established as described below.
SERVICE SPECIFICATIONS
ItemsStandard value
Clutch pedal height mm163.5–166.5
Clutch pedal clevis pin play mm1–3
Clutch pedal free play mm6–13
Distance between the clutch pedal and the toeboard when
the clutch is disengaged mm85 or more
LUBRICANTS
ItemsSpecified lubricantsQuantity
Clutch fluidBrake fluid DOT 3 or DOT 4As required
Push rod assemblyRubber grease
Boot
Release cylinder push rodMITSUBISHI genuine grease
Part No. 0101011
ON-VEHICLE SERVICE

CLUTCH PEDAL INSPECTION AND
ADJUSTMENT
1. Turn up the carpet, etc. under the clutch pedal.
2. Measure the clutch pedal height.
Standard value (A): 163.5 – 166.5 mm
3. If the height of the clutch pedal is outside the standard
value, loosen the locking nut and adjust the pedal height
to the standard value using the adjusting bolt or push
rod.
Clutch pedal height
A
Setting nutAdjusting bolt
Locking
nut
13 Nm

CLUTCH – On-vehicle Service21A-3
4. Measure the clutch pedal play.
Standard value (B): 1 – 3 mm
5. If the clutch pedal play is not within the standard value,
loosen the setting nut and move the push rod to adjust.
Caution
Do not push in the master cylinder push rod at this
time.
6. After completing the adjustments, confirm that the clutch
pedal free play (measured at the face of the pedal pad)
and the distance between the clutch pedal (the face of
the pedal pad) and the toeboard when the clutch is
disengaged are within the standard value ranges.
Standard value (C): 6–13 mm
Standard value (D): 85 mm or more
7. If the clutch pedal free play and the distance between
the clutch pedal and the toeboard when the clutch is
disengaged do not agree with the standard values, it
is probably the result of either air in the hydraulic system
or a faulty master cylinder or clutch. Bleed the air, or
disassembly and inspect the master cylinder or clutch.
8. Turn back the carpet, etc.
BLEEDING
Specified fluid: Brake fluid DOT 3 or DOT 4
Caution
Use the specified brake fluid. Avoid using a mixture of
the specified fluid and other fluid.
Clutch pedal clevis pin play
B
Clutch pedal free play
Distance between the clutch pedal and the
toeboard when the clutch is disengagedC
D