trunk MITSUBISHI LANCER EVOLUTION VI 1999 Workshop Manual

REAR AXLE – Hydraulic Unit 27-39
HYDRAULIC UNIT
REMOVAL AND INSTALLATION
Caution
(1) When connecting the return hose and suction hose, do not apply lubricant.
(2) No foreign matter should be allowed in the hydraulic piping and joints.
Pre-removal Operation

Trunk Side Trim Removal

Hydraulic Piping Fluid DrainingPost-installation Operation

Hydraulic Piping Fluid Filling and Bleeding
(Refer to P.27-32, 34.)

Trunk Side Trim Installation
1 23 45
6
7 8 9
10 11 12
1314
12 Nm
4
12 Nm
18 Nm
12 Nm
12 Nm 18 Nm
34 Nm
34 Nm
Removal steps
1. Dust guard
2. Suction hose and return hose con-
nection
3. Hydraulic unit hose assembly con-
nection
4. Hydraulic unit and bracket assem-
bly mounting bolt
C5. Hydraulic unit and bracket assem-
bly
A6. Hydraulic unit7. Hydraulic unit bracket
8. AYC harness
9. Hydraulic unit bracket
10. Hydraulic unit hose assembly
B11. Return hose
B12. Suction hose
A13. Grommet
14. Oil reservoir

EXTERIOR – Washer Tank and Hoses51-6
WASHER TANK AND HOSES
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operations

Washer Fluid Draining and Pouring

Trunk Side Trim (L.H.) Removal and Installation

2 1 3 5
4 6
To rear washer
To windshield washer5 Nm
6
6
5
5
6
Washer tank removal steps
1. Washer tank assembly
2. Washer tank bracket
A3. Washer motor (rear)
A4. Washer motor (front)Washer hose removal steps

Front seat and rear seat

Floor carpet
5. Washer hose
6. Joint
INSTALLATION SERVICE POINT
AWASHER MOTOR (FRONT) / WASHER MOTOR
(REAR) INSTALLATION
When installing the washer motors, pay special attention to
the following:
1. Connector shape (front: 2-pole round connector, rear:
2-pole square connector)
2. Connection of washer tubes

EXTERIOR – Marks51-9
2. EVOLUTION-VI mark
Application tape end
Align bottom edge of
application tape with
that of trunk lid.Align right side edge of
application tape with
trunk lid opening line.
3. LANCER mark
Trunk lid opening line
Rear bumper line 38 mm 18 mm
INSTALLATION
1. Clean the mark installation surfaces on the body with
unleaded petrol.
2. Peel off the backing paper from the reverse side of the
marks, and then attach the marks to the vehicle body
so that they fit properly into position.
Caution
(1) When attaching the marks, the surrounding
temperature should be 20 – 38°C and the air should
be completely free from dust.
(2) If the surrounding temperature is lower than 20°C,
the marks and the places on the body where the
marks are to be attached should be heated to
20 – 30°C.
(3) After sticking, press the marks strongly against
the body panels. Neglecting this could cause
peeled off marks.

– Ducts HEATER AND MANUAL
AIR CONDITIONER55-32
9
Rear ventilation duct removal steps

Rear bumper assembly

Trunk side trim
9. Rear ventilation duct

– Luggage Compartment WIRING HARNESS
CONFIGURATION DIAGRAMS
Connector
symbol
F
Glass
antenna
amplifier
NOTE
The connectors with framed
number are newly introduced.
C-14
LUGGAGE COMPARTMENT
F-01 (1-B) Defogger (–)
F-02 (1-B) Defogger (–)
F-03 (2) Choke coil
F-04 (3) Choke coil
F-05 (2) Trunk room lamp
F-06 (2) Vacant connector or high mounted stop
lamp (installed on rear shelf)
F-08 (2-B) Rear speaker (RH)
F-09 (1-B) Defogger (+)
F-10 (1-B) Defogger (+)
F-11 (3) Rear wiper motor
F-12 (1-B) Rear door switch (RH)
F-13 (2) High mounted stop lamp (installed on rear
spoiler)
F-15 (6) Rear combination lamp (RH)
F-16 (2-GR) Licence plate lamp (RH)
F-17 (1-B) Trunk room lamp switch
F-18 (2-GR) Licence plate lamp (LH)F-20 (6) Rear combination lamp (LH)
F-23 (2-B) Rear speaker (LH)
F-24 (1) Glass antenna

F-25 (1) Glass antenna
F-26 (1-B) Rear door switch (LH)
F-27 (3-B) Proportioning valve
F-28 (2-B) Direction valve (LH)
F-29 (2-B) Direction valve (RH)
F-30 (8-B) Rear harness and AYC harness combina-
tion
F-31 (2-B) Accumulator pressure switch

F-32 (2-B) AYC motor
F-33 (6) CD changer
F-34 (2) Rear window washer
F-35 (2) Windshield washer motor