diagram MITSUBISHI LANCER EVOLUTION VIII 2004 User Guide

SERVICE MANUAL
ELECTRICAL WIRING DIAGRAMS
Supplement

LANCER
EVOLUTION VIII
MR
FOREWARD
This manual contains information about the main
changes in the 2004 Lancer Evolution VIII MR.
It only covers those points that are different from the
previous model. Therefore, when inspecting or
repairing electrical parts, this manual should be used in
conjunction with the related documents listed on the
following pages, if necessary.
This manual contains various different types of wiring
diagrams and circuit diagrams, but it should be
remembered that these may not always coincide with
the exact specifications of each individual vehicle.
This manual is based on the vehicle specifications as of
February 2004.
Please note that future vehicles may not match the
contents of this manual completely, due to changes in
specifications, or the like.
The units shown in this manual are the standard
international SI units. Conventional units are not
included.
February 2004
MITSUBISHI MOTOR CORPORATIONGeneral
Wiring Diagrams
Component Installation Positions
Circuit Diagrams
1
2
3
0
This manual is printed on recycled paperAny opinions, requests, or questions concerning this
manual, should be written on the ‘Servicing Comments
Form’ at the end, and sent to us by fax.
CONTENTS

Related documentation
Cautionary Note regarding servicing of vehicles fitted with SRS airbags and/or seatbelts with
pre-tensioner systems.
Warnings:
1. Incorrect inspection or servicing of a component part of the SRS airbag system or seatbelt pre-tensioner system, or
a part relating to these systems, may cause accidental operation (deployment) of the SRS airbag or seatbelt pre-
tensioners, or may cause these systems to be disabled, leading in either case the risk of serious injury.
2. If parts may be affected by heat during painting operations, then those parts must be removed in advance. This
applies to the SRS-ECU, airbag modules (driver’s sear and front passenger’s seat), clock springs, front impact
sensors, side impact sensors, and pre-tensioner seatbelts.
• 93ºC or above : SRS-ECU, airbag modules (driver’s sear and front passenger’s seat), clock springs, front impact
sensors, side impact sensors
• 90ºC or above : Pre-tensioner seatbelts
3. The component parts of the SRS airbag system or seatbelt pre-tensioner system, and parts relating to these
systems, must always be inspected and serviced by a Mitsubishi dealer.
4. Service personnel must read the relevant service manuals (particularly, Section 52B – SRS Airbags) carefully and
thoroughly, before inspecting or servicing the component parts of the SRS airbag system or seatbelt pre-tensioner
system, and parts relating to these systems.
Title of Document No. Date of
IssueTitle of Document No. Date of
Issue
Body Manuals (Service Manual)
• Mirage, Lancer (supplement)
• Lancer Cedia
• Lancer Cedia (supplement)
• Lancer Evolution VII
(supplement)
• Lancer Cedia (supplement)
• Lancer (supplement)
• Lancer Evolution VIII MR
(supplement)1036F52
1036K50
1036K51
1036K52
1036K53
1036K54
1036K55Aug 1996
May 2000
July 2000
May 2001
Oct 2001
Feb 2003
Feb 2004
Electrical Wiring Diagrams
Service Manual
• Lancer Evolution VIII 1036K77 Jan 2003
New Vehicle Manuals
• Mirage, Lancer
• Mirage, Lancer
• Mirage, Lancer
• Mirage, Lancer
• Mirage
• Mirage, Lancer
• Lancer
• Lancer
• Lancer Cedia
• Lancer Cedia
• Lancer Evolution VII
• Lancer Cedia
• Lancer Cedia
• Lancer Evolution VII
• Lancer Cedia
• Lancer Evolution VIII
• Lancer
• Lancer
• Lancer Evolution VIII MR1036F30
1036F31
1036F32
1036F33
1036F34
1036F35
1036F36
1036F37
1036K30
1036K31
1036K32
1036K33
1036K34
1036K35
1036K36
1036K37
1036K38
1036K39
1036K40Oct 1995
Jan 1996
Aug 1996
Jul 1997
Jan 1998
Oct 1998
Jan 1999
Dec 1999
May 2000
July 2000
Jan 2001
May 2001
Oct 2001
Jan 2002
May 2002
Jan 2003
Feb 2003
Dec 2003
Feb 2004Engine Service Manual
• 4G6 Engine
• 4G6 Engine (supplement)1039G46
1039G63Jan 2001
Jan 2003
Service Manuals
• Lancer Cedia
• Lancer Cedia (supplement)
• Lancer Evolution VII
(supplement)
• Lancer Cedia (supplement)
• Lancer Cedia (supplement)
• Lancer Evolution VII
(supplement)
• Lancer Cedia (supplement)
• Lancer Evolution VIII
(supplement)
• Lancer (supplement)
• Lancer (supplement)
• Lancer Evolution VIII MR
(supplement)1036K00
1036K01
1036K02
1036K03
1036K04
1036K05
1036K06
1036K07
1036K08
1036K09
1036K10May 2000
July 2000
Jan 2001
May 2001
Oct 2001
Jan 2002
May 2002
Jan 2003
Feb 2003
Dec 2003
Feb 2004Transmission Service Manual
• W5M51 Manual Transmission
• W5M51 Manual Transmission
(supplement)
• W6MAA Manual Transmission1039M17
1039M22
1039M23Jan 2001
Jan 2003
Jan 2003

0-1
SECTION 0
GENERAL INFORMATION
CONTENTS
Vehicle Identification ..............................0-2
Implementation Code .............................0-2Details of Changes .................................0-2
Wiring Diagrams ................................................0-2
Component Installation Positions ......................0-2
Circuit Diagrams ................................................0-3
List of Circuit Diagrams .........................0-5

GENERAL INFORMATION - VEHICLE IDENTIFICATION0-2
Model
codeClass
code2004
codeGrade Engine model Transmission
modelFuel
supply
system
GH-CT9A SNDFZ!
RS W5M51
(4WD, 5M/T)
SJDFZ!
RS
SJGFZ!
GSR4G63 (2000
DOHC 16-valve
intercooler turbo)
W6MAA
(4WD, 6M/T)MPI
Connector
CodeName Page Details of Change
BEngine transmission p.1-2• Due to changes in the engine control system, the
name of the wastegate solenoid valve (B-30) has
been changed to “wastegate solenoid valve 1”, and
an additional wastegate solenoid valve 2 (B-32) has
been added.
• The 4WD-ECU (C-37, 38) has been moved from
the instrument panel harness to the control harness.
• With the removal of the DVD-MMCS, the following
connectors have been removed.

• Multi-centre display (C-11, 12)

• Navigation unit (C-47)
The immobiliser ECU (C-54) has also been removed,
due to changes in the engine immobiliser system.
CInstrument panel p.1-4
• With the removal of the DVD-MMCS, the following
connectors have been removed.

• Audio unit (C-102)

• Hazard switch (C-105)
FBoot interior p.1-6• Spare connector (F-28) added.
Changed part Page Details of change
ECU p.2-2• With changes in the engine immobiliser system, the
installation position of the immobiliser ECU has been
changed.
Solenoid valve p.2-2• With the addition of the wastegate solenoid valve 2, a
new installation point has been provided.
VEHICLE IDENTIFICATION
M3000000100845
Note:


denotes a continued model
IMPLEMENTATION CODE
M3000001000584
GH-CT9A ; CT9A-0300001 ~
DETAILS OF CHANGES
Wiring diagrams
M3000003000159
Component installation positions
M3000004000141

GENERAL INFORMATION - DETAILS OF CHANGES0-3
Main circuit Name of circuit Page Details of change
J/C - p.3-2• Partial changes to circuit and
destination system names in J/C(1) —
(6)
-• With the introduction of manual air
conditioning, the circuit used by the
fusible link No.2 has been changed.
• Wastegate solenoid valve 2 added to
load of special fuse No.3.
• Rating of special fuse No.10 changed
from 15A to 20A.
Power supply - p.3-10• Partial changes to destination system
names.
• Earth No.13 added.
• Rating of special fuse No.10 changed
from 15A to 20A.
• Partial changes to circuit details, due
to removal of sunroof.
Engine control - p.3-16• Rating of special fuse No.10 changed
from 15A to 20A.
• Earth No.13 added.
• Some changes to circuit, due to
addition of wastegate solenoid valve
2 (B-32).
• Partial changes, due to removal of
DVD-MMCS
Lighting Interior lights, boot interior
light, ignition key cylinder
illumination light, door not
closed indicator light-• Change to terminal number in J/C(2)
(C-119) on line linking ETACS and
diagnosis connector. (No.1 " No.5)
Reversing lights -• Change to terminal number in J/C(2)
(C-119) on line linking reversing light
and rear combination light (LH).
(No.18 " No.19)Signal
Stop lights p.3-24• Spare connector (F-28) added, and
circuit partially changed.
Meters / Gauges -Meters
Remaining fuel warning
light, oil pressure warning
light, brake warning light,
seatbelt warning light-• Change to terminal number in J/C(1)
(C-07) on line inking J/B (general fuse
No.18) and combination meter. (No.4
" No.8)
• Change to terminal number in J/C(4)
(C-110) on line linking combination
meter and fuel gauge unit (sub).
(No.20 " No.21)
Door opening
controlElectric windows -• Change to terminal number in J/C(2)
(C-119) on line linking power window
main switch and diagnosis connector.
(No.12 " No.14)
Fully automatic air
conditioning-• Change to terminal number in J/C(1)
(C-07) on line linking J/B (general
fuse No. 18) and A/C-ECU. (No.6 "
No.4)
• Change to terminal number in J/C(5)
(C-06) on line linking A/C-ECU and
diagnosis connector. (No.8 " No.9)Air
conditioning
Manual air conditioning p.3-26• With the adoption of manual air
conditioning, a new circuit has been
installed.
Windscreen wipers and
washers-Safety and
visibility
Electric retractable remote
control door mirrors-• Change to terminal number in J/C(2)
(C-119) on line linking ETACS and
diagnosis connector. (No.1 " No.5)
Circuit diagrams
M3000004500157

GENERAL INFORMATION - LIST OF CIRCUIT DIAGRAMS0-5
Main circuit Name of Circuit Circuit Diagram
J/B -!
J/C -#
Central junction -#
Power supply -#
Start up -!
Ignition -!
Charging -!
Engine control -#
Coolant -!
Headlights (excluding discharge type)!
Headlight (discharge type)!
Tail lights, side lights, licence plate lights, lighting monitor
warning buzzer!
Cabin lights, boot interior light, ignition key cylinder
illumination light, door not closed indicator light *2!
Fog lights!
Lighting
Headlight levelling system
!
Indicator lights, hazard warning lights!
Reversing lights *2!
Stop lights#
Signalling
Horn
!
Meters / Gauges *2!Meters
Remaining fuel warning light, oil pressure warning light,
brake warning light, seatbelt warning light *2
!
Electric windows *2!
Central door locking (vehicle not fitted with keyless entry)!
Door opening control
Central door locking (vehicle fitted with keyless entry)
!
Heater!
Fully automatic air conditioning!
Air conditioning
Manual air conditioning
#
List of Circuit Diagrams
M3000006000169
Notes:
1. This list of circuit diagrams indicates whether each circuit has been modified or added.
2. The “●” symbol indicates a circuit that has been modified or added. Diagrams for these circuits are included in
this supplement.
3. The “


” symbol indicates a circuit that is unchanged. Details of these circuits can be found in the existing
Electrical Wiring Diagram manual (’03-1 No.1036K77).
4. The “X” symbol indicates a circuit that is unrelated to the vehicle referred to in this manual.
5. The “*1” symbol marks circuits whose names have been changed the previous names.
6. The “*2” symbol marks circuits whose J/C terminal numbers have changed. For more information, please refer
to the “Details of Changes” table above.

GENERAL INFORMATION - LIST OF CIRCUIT DIAGRAMS0-6
Main circuit Name of Circuit Circuit Diagram
Windscreen wipers, washers *2!
Rear wiper, washer!
Demister (vehicle not fitted with fully automatic A/C)!
Demister, door mirror heating elements (vehicle fitted with
fully automatic A/C)!
Safety / Visibility
Electric retractable remote control door mirrors *2
!
Spare Audio connectors *1,2!
DVD-MMCS X
Clock *1,2!
Accessories
Cigar lighter, ashtray illumination light
!
ABS#
ACD (vehicle not fitted with AYC)#
ACD, AYC#
SRS airbags, seatbelt pre-tensioners (vehicle not fitted
with side airbags)!
SRS airbags, seatbelt pre-tensioners (vehicle fitted with
side airbags)!
Sun roof X
Ignition key reminder buzzer!
Intercooler water spray *2!
Engine immobiliser system#
Security alarm!
Spare connectors for fog lights!
Special Equipment
Spare general connectors *2
!

1-1
SECTION 1
WIRING DIAGRAMS
CONTENTS
Engine transmission ..............................1-2 Instrument panel .....................................1-4
Boot interior ............................................1-6

WIRING DIAGRAMS - ENGINE TRANSMISSION1-2
ENGINE TRANSMISSION
M3010000400494
B-01 (1-black) Engine oil pressure switch
B-02 (1) Alternator
B-03 (4-grey) Alternator
B-04 (1) Starter
B-05 (1-black) Starter
B-06 (4-black) Throttle position sensorB-07 (2-black) Purge control solenoid valve
B-08 (7-black) Airflow sensor
B-12 (5-grey) Windscreen wiper motor
B-13X (1) Engine speed detection connector
B-14X (5) Starter relay
B-17X (4) Ignition coil relay
Connector
symbol -
B
-01
∫
-32
AC311230AB
Control harness
Battery harness