clock MITSUBISHI LANCER SPORTBACK 2010 8.G Owner's Manual

For emergencies
6-11
6
To remove the compact spare tire
N00849700231
1. Lift up the board.
2. To remove the spare tire, remove the installation clamp
(A) by turning it counterclockwise.NOTE

The clamp cannot be used for a normal size tire. Store a
normal size tire under the board.
NOTE

Put the spare tire under the vehicle body near the jack.
This makes it safer if the jack slips out of position.
BK0103001US.book 11 ページ ２００９年８月２０日　木曜日　午前１０時４５分

6-16 For emergencies
6
NOTE

Flange nuts can be temporarily used on the compact spare
or steel wheel as shown in the illustration, but return them
to the original wheel and tire as soon as possible.


If all four wheels are changed to steel wheels, use tapered
nuts.8. Lower the vehicle slowly by rotating the wheel nut
wrench counterclockwise until the tire touches the
ground.
CAUTION
!

Never apply oil to either the wheel bolts or the nuts
or they will tighten too much.
BK0103001US.book 16 ページ ２００９年８月２０日　木曜日　午前１０時４５分

7-24 Vehicle care and maintenance
7
2. Turn the plastic nuts (C) counterclockwise, and then
remove the battery upper cover (D).NOTE

Be careful not to lose the removed plastic nuts.
To i n s t a l l1. Install the battery upper cover (A) onto the battery, and
then push the plastic nuts (B) in the direction shown by
the arrows to secure the cover.NOTE

Be sure to install the plastic nuts in the correct direction.


Make sure that the battery upper cover is installed
securely.
2. To install the air duct, perform the removal steps in
reverse.
BK0103001US.book 24 ページ ２００９年８月２０日　木曜日　午前１０時４５分

7-62 Vehicle care and maintenance
7
2. For vehicles equipped with turbocharger, when replacing
the bulb on the passenger’s side, lift up the engine coolant
reservoir (B).3. Turn the bulb (C) counterclockwise, and then remove the
headlight bulb with holder.*- Front of the vehicle
*- Front of the vehicle
BK0103001US.book 62 ページ ２００９年８月２０日　木曜日　午前１０時４５分

7-64 Vehicle care and maintenance
7
Headlights (high beam, except for vehicles
equipped with high intensity discharge head-
lights)
N00901900047
1. When replacing the bulb on the front passenger’s side,
remove the bolt (A) holding down the washer tank spout
and move the spout toward the rear of the vehicle.2. Turn the cap (B) counterclockwise to remove it.*- Front of the vehicle
*- Front of the vehicle
BK0103001US.book 64 ページ ２００９年８月２０日　木曜日　午前１０時４５分

Vehicle care and maintenance
7-65
7
3. Turn the bulb (C) counterclockwise to remove it. 4. While holding down the tab (D), pull out the bulb (E).
5. To install the bulb, perform the removal steps in reverse.*- Front of the vehicle
BK0103001US.book 65 ページ ２００９年８月２０日　木曜日　午前１０時４５分

Vehicle care and maintenance
7-67
7
2. Turn the cap (B) counterclockwise to remove it. 3. Turn the socket (C) counterclockwise to remove it.*- Front of the vehicle
*- Front of the vehicle
BK0103001US.book 67 ページ ２００９年８月２０日　木曜日　午前１０時４５分

7-68 Vehicle care and maintenance
7
4. Turn the bulb counterclockwise while pressing it and pull
it out of the socket.
5. To install a bulb, perform the removal steps in reverse.
Headlights (low/high beam, for vehicles equipped
with high intensity discharge lights)
N00902000029
Do not attempt to disassemble or repair headlights, and do not
attempt to replace their bulbs.Adjustment of headlight aim
N00943200121
The alignment of the headlights should be checked by an
authorized Mitsubishi Motors dealer or a repair facility of your
choice.
WA R N I N G
!

A high voltage is present in the power circuit and in
the bulbs and bulb terminals. To avoid the risk of an
electric shock, contact an authorized Mitsubishi
dealer whenever repair or replacement is necessary.
BK0103001US.book 68 ページ ２００９年８月２０日　木曜日　午前１０時４５分

7-70 Vehicle care and maintenance
7
3. Turn the socket (C) counterclockwise to remove it. 4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.*- Front of the vehicle
BK0103001US.book 70 ページ ２００９年８月２０日　木曜日　午前１０時４５分

7-72 Vehicle care and maintenance
7
3. Turn the socket (D) counterclockwise to remove it.
4. Pull the bulb out of the socket.5. To install the bulb, perform the removal steps in reverse.
BK0103001US.book 72 ページ ２００９年８月２０日　木曜日　午前１０時４５分