CD player MITSUBISHI MIRAGE 2014 6.G MMCS Manual

133
Problem Measure
Sound skips.
Noise is heard.The disc may be dirty. Wipe the disc with a soft cloth.
Disc is heavily scratched or warped. Replace with a disc with no scratches.
MP3/WMA/AAC files are not encoded properly. Use MP3/WMA/AAC files encoded properly.
Sound quality is poor just after the power has
been turned on.Moisture may have condensed on the internal lens. Leave the unit turned on for about 1 hour to dry it
out before using it.
A disc cannot be inserted. Another disc is already inserted into the DVD player.
É “Inserting/Ejecting a Disc” (page 101)
MP3/WMA/AAC sound skips. Check if the sound skips during playback via a computer, etc.
MP3/WMA/AAC sound skips/cuts out. Use different encoding software to record audio.
MP3/WMA/AAC sound quality is poor. Increase the sampling frequency and bit rate.
É “About MP3/WMA/AAC files” (page 112)
Certain folders and files cannot be played. Delete all data other than audio data when creating files. Playback is not possible if there are files
stored lower than 8 folder levels, if the number of folders (including the root) exceeds 255, or if the
number of files in a folder exceeds 512.
The display is incorrect. Set the disc format to ISO9660 Level 1 or ISO9660 Level 2 using your disc writing software.
MP3/WMA/AAC files on a CD Extra cannot
be played.Record MP3/WMA/AAC files in session 1 of the CD Extra.
“Disc read error.” is displayed. Insert the disc with its label facing upward.
Disc cannot be played with the display
“Please change the parental level to play
this disc.” shown.The view is limited. Release the view limitation or change the parental level.
É “Setting up the parental level” (page 111)
The color of the display is light or a shade of
color is not good.The color is not adjusted adequately. Check that the Brightness, Color, and Black Level are adjusted
properly.
205-0010-00_QY-7375M-A_EN.indb 133205-0010-00_QY-7375M-A_EN.indb 1333/12/2013 9:57:30 AM3/12/2013 9:57:30 AM

135
Problem Measure
The iPod cannot be operated. Disconnect the USB connection, start playback from the iPod, and then reconnect the iPod.
Disconnect the USB connection, reset the iPod, and then reconnect the iPod.
Audio is not output from the iPod. From your iPod, change the audio output setting from Bluetooth (“Car-Navi”) to the dock connector.
Disconnect the iPod and then reconnect it.
Bluetooth Audio
Problem Measure
The Bluetooth device cannot connect with
the unit.Correctly connect a Bluetooth-compatible mobile phone.
É “Pairing a Bluetooth audio player” (page 120)
Turn on the power of the audio device.
Connection may not be possible and sound may skip depending on the location of the Bluetooth audio
device. Place the Bluetooth audio device in an area with good signal transmission.
Playback is not possible. Use an audio device compatible with AVRCP.
Disconnect the audio device, and then reconnect it.
Start the player of the connected audio device.
Track names, artist names, and album names
are not displayed correctly.Use an audio device compatible with AVRCP 1.3.
Perform playback by initiating playback from the player of the connected audio device.
Audio is no longer output from the connected
audio device.Select the Bluetooth audio device again from the Bluetooth setting screen.
If an error display other than the ones described above appears, turn off and on the ACC power to restart the system. If the problem persists, consult
your Mitsubishi Motors dealer.
205-0010-00_QY-7375M-A_EN.indb 135205-0010-00_QY-7375M-A_EN.indb 1353/12/2013 9:57:30 AM3/12/2013 9:57:30 AM