Ground MITSUBISHI MIRAGE 2014 6.G User Guide

For emergencies
6-23
6
4. Insert the bar (D) into the wheel nut wrench (E). Then put
the end of the bar into the shaft’s jack end, as shown in the
illustration.
Slowly rotate the wheel nut wrench until the tire is raised
slightly off the ground surface.
5. Remove the wheel nuts with the wheel nut wrench, then
take the wheel off.
WA R N I N G
!
Stop jacking up the vehicle as soon as the tire is
raised off the ground. It is dangerous to raise the
vehicle any higher.
Do not get under your vehicle while using the jack.
Do not bump the raised vehicle or leave it sitting on
the jack for a long time. Both are very dangerous.
Do not use a jack except the one that came with your
vehicle.
The jack should not be used for any purpose other
than to change a tire.

No one should be in your vehicle when using the
jack.
Do not start or run the engine while your vehicle is
on the jack.
Do not turn the raised wheel. The tires that are still
on the ground could turn and make your vehicle fall
off the jack.
CAUTION
!
Handle the wheel carefully when changing the tire,
to avoid scratching the wheel surface.
WA R N I N G
!
BK0162600US.book 23 ページ ２０１３年３月２２日　金曜日　午後２時４１分

For emergencies
6-25
6
7. Install the wheel nuts with their tapered ends facing
inward, then tighten by hand until the wheel is no longer
loose.8. Lower the vehicle slowly until the tire touches the ground,
by rotating the wheel nut wrench counterclockwise.
CAUTION
!
Never apply oil to either the wheel bolts or the nuts
or they will tighten too much.
Steel wheel
Aluminum wheel
BK0162600US.book 25 ページ ２０１３年３月２２日　金曜日　午後２時４１分

6-30 For emergencies
6
Towing the vehicle by a tow truck
Do not tow CVT vehicles with this style.
CAUTION
!
This vehicle must not be towed by a tow truck using
sling lift type equipment (Type A) as illustrated.
Using a sling lift will damage the bumper and front
end.
Do not tow continuously variable transmission
(CVT) vehicles with the driving wheels on the
ground (Type B) as illustrated. If the vehicle is
towed like this, the continuously variable transmis-
sion (CVT) fluid may not reach all parts of the
transmission, thus damaging it.
If you tow CVT vehicles, use Type C, D or E equip-
ment.
If the manual transaxle is malfunctioning or dam-
aged, transport the vehicle with the driving wheels
on a carriage (Type C, D or E) as illustrated.
BK0162600US.book 30 ページ ２０１３年３月２２日　金曜日　午後２時４１分

For emergencies
6-31
6
Towing with rear wheels off the ground (Type B - M/T
vehicles only)Set the gearshift lever to the “N” (Neutral) position.
Secure the steering wheel in a straight-ahead position with a
rope or tie-down strap.
Towing a front-wheel drive vehicle with front wheels off
the ground (Type C)Release the parking brake.
Place the gearshift lever in the “N” (Neutral) position (manual
transaxle) or the selector lever in the “N” (NEUTRAL) posi-
tion (CVT).

If the vehicle is towed with the ignition switch in the
“ON” position or the operation mode in ON and
only the front wheels or only the rear wheels raised
off the ground (Type B or C), the Active Stability
Control (ASC) may operate, resulting in an acci-
dent. When towing the vehicle with the rear wheels
raised, turn the ignition switch to the “ACC” posi-
tion or put the operation mode in ACC. When tow-
ing the vehicle with the front wheels raised, keep the
ignition switch or the operation mode as follows.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch is in “OFF” or “ACC” position.
[Vehicles equipped with the F.A.S.T.-key]
The operation mode is in OFF or ACC.
CAUTION
!
BK0162600US.book 31 ページ ２０１３年３月２２日　金曜日　午後２時４１分