turn signal MITSUBISHI MIRAGE 2014 6.G User Guide

3-32 Features and controls
3
Answerback functionThe horn of the keyless entry system answerback function can
be changed as required. This is done with the key removed
from the ignition switch.
Horn deactivation/reactivation
The answerback function can be set in the following three
ways.
1. Put the operation mode in OFF.
2. Open the driver’s door and turn the combination head-
lights and dimmer switch to the “OFF” position.
3. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
4. Release in sequence the UNLOCK and LOCK buttons
within 10 seconds of pressing the UNLOCK button in step
3.Turn signal light deactivation/reactivation
The turn signal lights answerback function can be changes.
If you want to change the answerback function, please contact
an authorized Mitsubishi Motors dealer.
Buzzer deactivation/reactivation
The buzzer answerback function can be turned ON or OFF as
required.
Setting of door and liftgate unlock function
N00544600098
The door and liftgate unlock function can be set to the follow-
ing two conditions.
Each time the door and liftgate unlock function is set, a chime
will sound to tell you the condition of the door and liftgate
unlock function.
1. Put the operation mode in OFF.
2. Open the driver’s door and turn the combination head-
lights and dimmer switch to the “OFF” position.
3. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
4. Release in sequence the LOCK and UNLOCK buttons
within 10 seconds of pressing the LOCK button in step 3.
One chime: The horn will not sound.
Two chimes: The horn will sound.
Four chimes: The horn will sound if the LOCK button is
pressed twice within 1 second.
Number of
chimes
Condition
One chime All doors and the liftgate unlock
Two chimes Driver’s door unlock only
BK0162600US.book 32 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-109
3 Indicator and warning light package
N00519800849
1- High beam indicator → P. 3 - 1 1 0
2- Electric power steering system warning light → P.3-75
3- Tire pressure monitoring system warning light (if so
equipped) → P.3-88
4- Turn signal indicators/Hazard warning lights → P. 3 - 1 1 0
5- Front fog light indicator (if so equipped) → P. 3 - 1 1 0
6- Door-ajar warning light → P. 3 - 1 1 4
7- Supplemental Restraint System (SRS) warning light
→ P.2-44
8- High coolant temperature warning light (red) → P. 3 - 1 1 3
9- Low coolant temperature indicator (green) → P. 3 - 1 1 0
10- Oil pressure warning light → P. 3 - 1 1 3
11- Engine malfunction indicator (“SERVICE ENGINE SOON”
or “Check engine light”) → P. 3 - 1 1 212- Charging system warning light → P. 3 - 1 1 3
13- Brake warning light → P.3-111
14- Anti-lock braking system warning light → P.3-73
15- Multi-information display → P.3-98
16- Driver ’s seat belt reminder/warning light → P.2-18
17- Cruise control indicator (if so equipped) → P.3-81
18- Active stability control (ASC) indicator/warning light →
P.3-78, 3-79
19- Active stability control (ASC) OFF indicator/warning light
→ P.3-78, 3-79
20- ECO indicator → P. 3 - 1 1 0
21- For details, refer to “Warning activator” on page 3-21 (if so
equipped)
22- For details, refer to “Warning activator” on page 3-21 (if so
equipped)
BK0162600US.book 109 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-110 Features and controls
3Indicators
N00519900127
Turn signal indicators/Hazard warning lights
N00520000216
The arrows will flash in time with the corresponding exterior
turn signals when the turn signal lever is used.
Both arrows will flash when the hazard warning flasher switch
is pressed.NOTE
If the indicator flashes faster than usual or if the indicator
stays on without flashing, check for a malfunctioning turn
signal light bulb or turn signal connection.High beam indicator
N00520100086
A blue light comes on when the headlights are on high beam.Front fog light indicator
(if so equipped)
N00520200175
This indicator comes on while the front fog lights are on.Low coolant temperature indicator - green
N00575600010
This indicator comes on in green while the coolant temperature
is low.NOTE
When the indicator goes out, this should be used as a
rough indication of when the heating starts working.
ECO indicator
N00568800036
This indicator comes on while fuel-efficient driving is
achieved.
BK0162600US.book 110 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-117
3
Headlight reminder buzzer
N00549800226
[When using a key to start the engine]
If the driver’s door is opened with the key in the “OFF” or
“ACC” position or removed from the ignition switch while the
lights are on, the tone will sound to remind you to turn off the
lights.
[When using the F.A.S.T.-key to start the engine]
If the driver’s door is opened with the operation mode is put in
OFF or ACC, or if the operation mode is changed to OFF while
the lights are on, the tone will sound to remind you to turn off
the lights.
In either case, the lights will turn off automatically and so will
the tone. Or you can turn the light switch to the “OFF” position
to stop the tone.
Dimmer (high/low beam change)
N00549900142
To change the headlights from high beam to low beam and vice
versa, pull the turn signal lever to (1). Switch the headlights to
low beam as a courtesy whenever there are oncoming vehicles,
or when there is traffic moving ahead of you. An illuminated
blue light in the instrument cluster indicates when the head-
lights are on high beam.
BK0162600US.book 117 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-118 Features and controls
3
Headlight flasher
N00550000185
You can flash the high beams by pulling the lever gently
toward you (2). The lights will go back to normal when you let
go. While the high beam is on, you will see a blue light on the
instrument panel.NOTE
You can flash the high beams by pulling the lever toward
you, even if the light switch is off.

If you turn the lights off with the head lights set to high-
beam illumination, the headlights are automatically
returned to their low-beam setting when the light switch is
next turned to the “ ” position.
Turn signal lever
N00522600519
When changing lanes, or to making a gradual turn, hold the
lever in the “lane change” position (1). It will return to the neu-
tral position when you let go. Use the full position (2) when
making a normal turn. The lever will return to the neutral posi-
tion when the turn is complete. There may be times when the
lever does not return to the neutral position. This usually hap-
pens when the steering wheel is turned only slightly. You can
easily return the lever by hand.
Also, when you move the lever to (1) slightly then release it,
the turn signal lights and the indicator light in the instrument
cluster will flash three times.
BK0162600US.book 118 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-119
3
NOTE
A light in the instrument panel flashes to show when the
turn signal lights are working properly.
If this light flashes faster than usual, check for a burned
out turn signal light bulb or malfunctioning connection in
the signal.
If the panel light does not come on when the lever is
moved, check for a blown fuse or a burned out bulb in the
panel.
Have the system inspected by your authorized Mitsubishi
Motors dealer or a repair facility of your choice.

It is possible to modify functions as follows:
• Deactivate the turn signal light 3-flash function for lane
changes.
• Adjust the time required to operate the lever for the 3-
flash function.
• Changing of the tone of a sounding buzzer as the turn
signal lights flash.
See your authorized Mitsubishi Motors dealer for details.
Hazard warning flasher switch
N00522700318
If you press the flasher switch, the turn signals will flash inter-
mittently, and so will the hazard warning lights. This is an
emergency warning system and should not be used when the
vehicle is in motion, except for emergencies.
If you need to leave your vehicle, the flashers will keep work-
ing after the ignition switch is removed or the operation mode
is put in OFF.NOTE
If the flashers are used for several hours, the battery will
run down. This could make it difficult or impossible to
restart your vehicle.
BK0162600US.book 119 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Driving safety
4-5
4 Vehicle preparation before driving
N00629000702
For a safer and more enjoyable trip, always check for the fol-
lowing:Seat belts and seats
Before starting the vehicle, make certain that you and all
passengers are seated and wearing their seat belts properly
(with children in the rear seat, in appropriate restraints),
and that all the doors and the liftgate are locked.

Move the driver’s seat as far backward as possible, while
keeping good visibility, and good control of the steering
wheel, brakes, accelerator, and controls. Check the instru-
ment panel indicators and multi-information display for
any possible problem.

Similarly, the front passenger seat should also be moved
as far back as possible.

Make sure that infants and small children are properly
restrained in accordance with all laws and regulations.DefrostersCheck these by selecting the defroster mode, and set the blower
switch on high. You should be able to feel the air blowing
against the windshield.
Refer to “Defrosting or defogging (windshield, door win-
dows)” on page 5-15, 5-26.
TiresCheck all the tires for heavy tread wear or uneven wear pat-
terns. Look for stones, nails, glass, or other objects stuck in the
tread. Look for any tread cuts or sidewall cracks. Check the
wheel nuts for tightness, and the tires (including spare tire) for
proper pressure. Replace your tires before they are heavily
worn out.
On vehicles equipped with a tire pressure monitoring system,
there is a risk of damage to the tire inflation pressure sensors
when the tire is replaced on the rim. Tire replacement should,
only be performed by an authorized Mitsubishi Motors dealer.LightsHave someone watch while you turn all the exterior lights on
and off. Also check the turn signal indicators and high-beam
indicators on the instrument panel.Fluid leaksCheck the ground under the vehicle after parking overnight, for
fuel, water, oil, or other leaks. Make sure all the fluid levels are
correct. Also, if you can smell fuel, you need to find out why
immediately and have it fixed.
BK0162600US.book 5 ページ ２０１３年３月２２日　金曜日　午後２時４１分

4-6 Driving safety
4Safe driving techniques
N00629200137
Even this vehicle’s safety equipment, and your safest driving,
cannot guarantee that you can avoid an accident or injury.
However, if you give extra attention to the following areas, you
can better protect yourself and your passengers:

Drive defensively. Be aware of traffic, road and weather
conditions. Leave plenty of stopping distance between
your vehicle and the vehicle ahead.

Before changing lanes, check your mirrors, your blind
spots, and use your turn-signal light.

While driving, watch the behavior of other drivers, bicy-
clists, and pedestrians.

Always obey applicable laws and regulations. Be a polite
and alert driver. Always leave room for unexpected
events, such as sudden braking.

If you plan to drive in another country, obey their vehicle
registration laws and make sure you will be able to get the
right fuel.
Driving during cold weather
N00629400474

Check the battery. At the same time, check the terminals
and wiring. During extremely cold weather, the battery
will not be as strong. Also, the battery power level may
drop because more power is used for cold starting and
driving.
Before driving the vehicle, check to see if the engine runs
at the proper speed and if the headlights are as bright as
normally. Charge or replace the battery if necessary. Dur-
ing extreme cold weather, it is possible that a very low
battery could freeze.

Warm the engine sufficiently. After starting the engine,
allow a short warm-up time to distribute oil to all cylin-
ders. Then drive your vehicle slowly.

Stay at low speeds at first so that the manual transaxle oil
or the automatic transaxle fluid has time to spread to all
the lubrication points.

Manual transaxle can be harder to shift in cold weather
conditions. This is normal and shifting will get easier as
the transaxle warms up.
WA R N I N G
!
The battery gives off explosive hydrogen gas. Any
spark or flame can cause the battery to explode,
which could cause serious injury or death.
Always wear protective clothes and a face mask
when working with your battery, or let a skilled
mechanic do it.
BK0162600US.book 6 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Comfort controls
5-65
5
To remove
Turn the pole (A) counterclockwise.
To i n s t a l l
Screw the pole (A) clockwise into the base (B) until it is
securely retained.NOTE
Be sure to remove the roof antenna in the following cases:
• When going into an automatic car wash.
• When placing a car cover over the vehicle.

Before driving into a structure that has a low ceiling, fold
down the antenna to prevent it from hitting the ceiling.
General information about your radio
N00733900455
Your vehicle’s radio receives both AM and FM stations.
The quality of your reception is affected by distance, obstacles,
and signal interference.Signal transmissionFM signals do not follow the earth surface nor are they
reflected by the upper atmosphere. For this reason, FM broad-
casts cannot be received over long distances. AM signals fol-
low the earth’s surface and are reflected by the upper
atmosphere. For this reason, AM broadcasts can be received
over longer distances.FM AM
25 to 40 mile radius
(40 to 64 km)100 mile radius
(160 km)
BK0162600US.book 65 ページ ２０１３年３月２２日　金曜日　午後２時４１分

For emergencies
6-11
6
NOTE
Do not pull out an object, such as a nail or screw, that pen-
etrates the punctured tire.

Move the vehicle so that the tire valve is positioned away
from the point where the tire touches the ground. If the
valve is near the point where the tire touches the ground,
the sealant may not enter the tire easily.
1. Park the vehicle on a safe, flat and level place.
2. Set the parking brake firmly.
3. On vehicles equipped with manual transaxle, stop the
engine and move the gearshift lever to the “R” (Reverse)
position.
On vehicles equipped with continuously variable trans-
mission (CVT), move the selector lever to the “P”
(PARK) position, and stop the engine.
4. Turn on the hazard warning flashers and set up a warning
sign, such as a warning triangle or flashing signal lamp, at
an adequate distance from the vehicle, and have all your
passengers leave the vehicle.
5. Take out the tire repair kit.
Make sure that the compressor switch is OFF.6. Shake the tire sealant bottle well.
NOTE
In cold conditions (when the ambient temperature is 32 °F
{0 °C} or lower), thickening of the tire sealant can make
the tire sealant hard to squeeze out of the bottle. Warm the
bottle between your hands inside the vehicle.
CAUTION
!
If the vehicle body is contaminated by the tire seal-
ant, wipe the tire sealant off immediately with a wet
cloth.
Immediately wash clothes contaminated with tire
sealant. The tire sealant may not be removed from
the clothes.
BK0162600US.book 11 ページ ２０１３年３月２２日　金曜日　午後２時４１分