Remove MITSUBISHI MIRAGE 2014 6.G Repair Manual

6-4 For emergencies
6
NOTE
Open the terminal cover before connecting the jumper
cable to the positive terminal of the battery.
(Refer to “Battery” on page 7-17.)

Use the proper cables suitable for the battery size.
Otherwise heat damage to the cables could result.
7. Connect one end of the other jumper cable to the nega-
tive (-) terminal of the booster battery (B), and then con-
nect the other end to the designated ground location of
the vehicle with the discharged battery (A) at the point
farthest from the battery.
8. Start the engine in the vehicle providing the boost. Let the
engine idle a few minutes, then start the engine in the
vehicle with the discharged battery.
9. After the engine is started, disconnect the cables in the
reverse order from the way you connected them.
Charging the battery by using an external bat-
tery charger
WA R N I N G
!
Be sure to follow the proper order when connecting
the batteries, of: →→→
Make sure that the connection is made to the cor-
rect designated location (as shown in the illustra-
tion) properly. If the connection is directly made to
the negative (-) terminal of the battery, the flamma-
ble gases from inside the battery might catch fire
and explode, causing personal injury.
When connecting the jumper cable, do not connect
the positive (+) cable to the negative (-) terminal.
Sparks can make the battery explode.
WA R N I N G
!
Always remove the battery from your vehicle when
the battery is charged by an external battery
charger.
Keep sparks, cigarettes, and flames away from the
battery because the battery could explode.
Keep your work area well vented when charging or
using the battery in an enclosed space.
Remove all the caps before charging the battery.
Electrolyte (battery acid) is made of corrosive
diluted sulfuric acid. If electrolyte comes in contact
with your hands, eyes, clothes, or the painted sur-
face of your vehicle, thoroughly flush with water. If
electrolyte gets in your eyes, flush them immediately
and thoroughly with water, and get prompt medical
attention.
Always wear protective clothing and goggles when
working near the battery.
Keep the battery out of the reach of children.
BK0162600US.book 4 ページ ２０１３年３月２２日　金曜日　午後２時４１分

6-6 For emergencies
6
5. If you do not see steam or spray coming from under the
hood, leave the engine on until the high coolant tempera-
ture warning light goes off. After the high coolant temper-
ature warning light has gone off, you can start driving
again. If the high coolant temperature warning light stays
on, turn off the engine.
6. When you do not see any more steam or spray, open the
hood. Look for obvious leaks, such as a split radiator
hose. Be careful as components will be hot. Any leak
source must be repaired.
7. If there is no obvious leak source, check the coolant level
in the engine coolant reserve tank. If there is none, or if it
is too low, slowly add coolant.8. If the engine coolant reserve tank needs coolant, you will
probably also need to add coolant to the radiator. Do not
loosen or remove the radiator cap until the engine has
cooled down.
9. Start the engine, and slowly add coolant, up to the bottom
of the filler neck. Use plain water if you have to (and
replace it with the right coolant as soon as possible).
10. Replace the radiator cap and tighten it fully. Check the
coolant temperature warning light. You can start driving
again when the high coolant temperature warning light
does not come on.
11. Have the system inspected by your authorized Mitsubishi
Motors dealer or a repair facility of your choice.
WA R N I N G
!
Before raising the engine hood, check to see if there
is steam or spray coming from under the hood.
Steam or spray coming from an overheated engine
could seriously scald you.
Do not open the hood until there is no steam or
spray.
WA R N I N G
!
Removing the radiator cap could scald you with
escaping hot water or steam. When checking the
radiator level, cover the cap with a cloth before try-
ing to remove it. Turn it slowly counterclockwise,
without pressing down, to the first notch. The pres-
sure in the system will then be let out. When the
pressure is COMPLETELY LET OUT, press down
and keep turning the cap counterclockwise until it
comes off.
BK0162600US.book 6 ページ ２０１３年３月２２日　金曜日　午後２時４１分

6-8 For emergencies
6
Jack
(if so equipped)
Before removing or storing the jack, move the driver’s seat
fully forward to access the jack from the rear seat area.
(Refer to “Front seat” on page 2-5.)
To r e m o v eTurn the shaft end of the jack in the direction (1) until the jack
fully retracts and remove the jack from the holder (A).To s t o r ePut the jack in the holder (A) and turn the shaft end of the jack
in the direction (2) by hand until the jack is firmly secured.
CAUTION
!
Never access, remove or store the jack from the
front of the driver’s seat. Doing so could damage
electrical wires under the driver’s seat.
WA R N I N G
!
After storing the jack in place, make sure the jack is
securely fixed in the holder.
If the jack is not fixed securely, it may move and hit
an occupant in an accident resulting in serious
injury or death. Also the jack may move forward
during driving and could interfere with driver’s
pedal operation causing an accident.
BK0162600US.book 8 ページ ２０１３年３月２２日　金曜日　午後２時４１分

For emergencies
6-11
6
NOTE
Do not pull out an object, such as a nail or screw, that pen-
etrates the punctured tire.

Move the vehicle so that the tire valve is positioned away
from the point where the tire touches the ground. If the
valve is near the point where the tire touches the ground,
the sealant may not enter the tire easily.
1. Park the vehicle on a safe, flat and level place.
2. Set the parking brake firmly.
3. On vehicles equipped with manual transaxle, stop the
engine and move the gearshift lever to the “R” (Reverse)
position.
On vehicles equipped with continuously variable trans-
mission (CVT), move the selector lever to the “P”
(PARK) position, and stop the engine.
4. Turn on the hazard warning flashers and set up a warning
sign, such as a warning triangle or flashing signal lamp, at
an adequate distance from the vehicle, and have all your
passengers leave the vehicle.
5. Take out the tire repair kit.
Make sure that the compressor switch is OFF.6. Shake the tire sealant bottle well.
NOTE
In cold conditions (when the ambient temperature is 32 °F
{0 °C} or lower), thickening of the tire sealant can make
the tire sealant hard to squeeze out of the bottle. Warm the
bottle between your hands inside the vehicle.
CAUTION
!
If the vehicle body is contaminated by the tire seal-
ant, wipe the tire sealant off immediately with a wet
cloth.
Immediately wash clothes contaminated with tire
sealant. The tire sealant may not be removed from
the clothes.
BK0162600US.book 11 ページ ２０１３年３月２２日　金曜日　午後２時４１分

6-16 For emergencies
6
NOTE
If the tire pressure does not rise to the specified level
within 10 minutes, the tire may be so severely damaged
that the tire sealant cannot be used for emergency repair.
Do not drive the vehicle. Please contact an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.
15. Turn OFF the compressor switch, then pull the power cord
plug out of the 12 V power outlet.NOTE
At this point the puncture hole is not sealed yet. Air will
continue to leak through the puncture hole until the emer-
gency repair procedure is completed (through step 17 or
step 18 of these instructions).
16. When you have inflated the tire to the specified pressure,
stow the compressor and bottle in the vehicle and
promptly start driving the vehicle so that the tire sealant
can spread evenly in the tire. Drive with great care. Do not
exceed a speed of 50 mph (80 km/h). Observe local speed
limits.17. After driving for 10 minutes or 3 miles (5 km), park the
vehicle in a safe place. Remove the air compressor from
the stowed position. Check the tire pressure using the air
pressure gauge on the compressor. If the tire pressure has
not dropped, the emergency repair procedure is complete.
Proceed to step 19.
If the tire pressure is insufficient, inflate the tire to the
specified pressure again and drive the vehicle carefully
without exceeding a speed of 50 mph (80 km/h).
Before driving, make sure that the compressor is stowed.
CAUTION
!
If you sense any abnormality while driving, stop the
vehicle and contact an authorized Mitsubishi
Motors dealer or a repair facility of your choice.
Otherwise the tire pressure may drop before the
emergency repair procedure is completed, rendering
the vehicle unsafe to drive.
CAUTION
!
If the tire pressure is lower than the minimum per-
mitted pressure (18 psi {130 kPa}), the tire cannot
successfully be repaired with the tire sealant. Do not
drive the vehicle any further. Contact an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.
BK0162600US.book 16 ページ ２０１３年３月２２日　金曜日　午後２時４１分

6-20 For emergencies
6
To remove spare tire
N00849700286
1. Lift up the floor board of the cargo area.
2. To remove the spare tire, remove the installation clamp
(A) by turning it counterclockwise.NOTE
The flat tire with a normal size wheel cannot be stored
beneath the floor board. Store the flat tire in the cargo
area.

The compact spare tire should be used only tempo-
rarily. While the compact spare tire is being used,
the tire pressure monitoring system will not function
properly. Have the tire replaced or repaired at an
authorized Mitsubishi Motors dealer or a repair
facility of your choice as soon as possible.
Do not go over 50 mph (80 km/h) when driving with
the compact spare tire.
Avoid sudden starting and braking when driving
with the compact spare tire.
Do not drive through automatic car washes and over
obstacles that could possibly damage the underside
of your vehicle. Because the compact spare tire is
smaller than the original tire, there is less clearance
between the ground and your vehicle.
Because the compact spare tire is designed only for
your vehicle, do not use it on any other vehicle.
Do not put the compact spare tire on a different
wheel, and do not put standard tires, snow tires,
wheel covers or trim rings on the compact spare
wheel. Otherwise, you could damage these parts or
other parts on your vehicle.
Do not use tire chains with your compact spare tire.
Using a chain could cause damage to your vehicle
and loss of the chains.
CAUTION
!
BK0162600US.book 20 ページ ２０１３年３月２２日　金曜日　午後２時４１分

For emergencies
6-21
6
To change a tire
N00849800447
1. On vehicles with wheel covers, first remove the covers
(refer to “Wheel covers” on page 6-27). Then, loosen the
wheel nuts with the wheel nut wrench. Do not remove the
wheel nuts yet.2. Place the jack under one of the jacking points (A) shown
in the illustration. Use the jacking point closest to the tire
you wish to change.
WA R N I N G
!
Set the jack only at the positions shown here. If the
jack is set at a wrong position, it could dent your
vehicle or the jack might fall over and cause per-
sonal injury.
Do not use the jack on a tilted or soft surface.
Otherwise, the jack might slip and cause personal
injury. Always use the jack on a flat, hard surface.
Before setting the jack, make sure there are no sand
or pebbles under the jack base.
BK0162600US.book 21 ページ ２０１３年３月２２日　金曜日　午後２時４１分

For emergencies
6-23
6
4. Insert the bar (D) into the wheel nut wrench (E). Then put
the end of the bar into the shaft’s jack end, as shown in the
illustration.
Slowly rotate the wheel nut wrench until the tire is raised
slightly off the ground surface.
5. Remove the wheel nuts with the wheel nut wrench, then
take the wheel off.
WA R N I N G
!
Stop jacking up the vehicle as soon as the tire is
raised off the ground. It is dangerous to raise the
vehicle any higher.
Do not get under your vehicle while using the jack.
Do not bump the raised vehicle or leave it sitting on
the jack for a long time. Both are very dangerous.
Do not use a jack except the one that came with your
vehicle.
The jack should not be used for any purpose other
than to change a tire.

No one should be in your vehicle when using the
jack.
Do not start or run the engine while your vehicle is
on the jack.
Do not turn the raised wheel. The tires that are still
on the ground could turn and make your vehicle fall
off the jack.
CAUTION
!
Handle the wheel carefully when changing the tire,
to avoid scratching the wheel surface.
WA R N I N G
!
BK0162600US.book 23 ページ ２０１３年３月２２日　金曜日　午後２時４１分

6-26 For emergencies
6
9. Tighten the nuts in the order shown in the illustration until
each nut has been tightened to the torque listed here.
65 to 80 ft-lb (88 to 108 N•m)
10. Lower the jack all the way and remove it.11. Check the tire inflation pressure. The recommended tire
pressure for your vehicle is listed on the tire and loading
information placard attached to the driver’s door sill as
shown in the illustration. Refer to “Tire inflation pres-
sures” on page 7-23.
CAUTION
!
Never use your foot or a pipe extension to apply
added force to the wheel nut wrench when tighten-
ing the wheel nuts. If you do so, you can over-tighten
the wheel nuts and damage the wheel, wheel nuts
and hub bolts.
BK0162600US.book 26 ページ ２０１３年３月２２日　金曜日　午後２時４１分

For emergencies
6-27
6
To store the flat tire or spare tire, jack, bar and
wheel nut wrench
N00850000175
Store the flat tire in the cargo area.
Reverse the removing procedure when storing the spare tire,
jack, bar and wheel nut wrench.
Refer to “To remove the spare tire” on page 6-20 and “Jack and
tools” on page 6-7.
Wheel cover (if so equipped)
N00849400225
To r e m o v eWrap the tip of the bar with a cloth, insert it into the notch pro-
vided in the wheel cover, and pry the cover away from the
wheel.
Using the same procedure at the other wheel cover notches,
work the wheel cover away from the wheel to remove it com-
pletely.NOTE
The wheel cover is made of plastic. Be careful when pry-
ing it off.
CAUTION
!
Driving with an improperly inflated tire can cause
an accident. If you have no choice but to drive with
an under-inflated tire, keep your speed down and
avoid sudden steering or braking, if possible. Inflate
the tire to the correct pressure as soon as possible.
Refer to “Tire inflation pressures” on page 7-23.
After changing the tire and driving the vehicle about
620 miles (1,000 km), retighten the wheel nuts to
make sure that they have not come loose.
If the steering wheel vibrates when driving after
changing the tire, have the tire checked for balance
at an authorized Mitsubishi Motors dealer or a
repair facility of your choice.
Do not mix one type of tire with another or use a dif-
ferent size from the one listed. This would cause
early wear and poor handling.
CAUTION
!
Trying to remove the wheel cover with only your
bare hands can seriously injure your fingers.
BK0162600US.book 27 ページ ２０１３年３月２２日　金曜日　午後２時４１分