MPG MITSUBISHI MIRAGE 2014 6.G Owners Manual

3-102 Features and controls
3
Average fuel consumption display
N00575300017
This displays the average fuel consumption from the last reset
to the present.
The reset mode conditions for the average fuel consumption
display can be switched between “Auto reset” and “Manual
reset”.
For information on how to change the average fuel consump-
tion display setting, refer to “Changing the function settings”
on page 3-105.NOTE
The average fuel consumption display can be reset sepa-
rately in both auto reset mode and manual reset mode.

“---” is displayed when the average fuel consumption can-
not be measured.

The initial (default) setting is “Auto reset mode”.

Average fuel consumption may vary depend on the driv-
ing conditions (road conditions, how you drive, etc.).
The actual fuel consumption may differ from the fuel con-
sumption displayed, so treat the fuel consumption dis-
played as just a rough guideline.

Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.

The display setting can be changed to the preferred units
{mpg, km/L, L/100 km}.
Refer to “Changing the function settings” on page 3-105.
Fuel remaining display
N00575400018
The fuel remaining display indicates the fuel level in the fuel
tank when the ignition switch or the operation mode in ON.NOTE
It may take several seconds to stabilize the display after
refilling the tank.

If fuel is added with the ignition switch or the operation
mode in ON, the remaining fuel display may incorrectly
indicate the fuel level.

The fuel lid mark (A) indicates that the fuel tank filler
door is located on the left side of the vehicle. (Refer to
“Filling the fuel tank” on page 1-4.)1- Full
0- Empty
BK0162600US.book 102 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-107
3
Auto reset mode

When the average fuel consumption is being displayed, if
you hold down the multi-information display switch,
these calculations will be reset to zero.

When the engine switch or the operation mode is in the
following conditions, the average fuel consumption dis-
play will automatically reset.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch has been set to the “ACC” or “OFF”
position for about 4 hours or more.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode has been set to ACC or OFF for about
4 hours or more.NOTE
The average fuel consumption display can be reset sepa-
rately for the auto reset mode and for the manual reset
mode.

Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.

The initial (default) setting is “Auto reset mode”.
Changing the fuel consumption display unit
N00557100156
The fuel consumption display unit can be changed. The dis-
tance and amount units are also switched to match the selected
fuel consumption unit.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the average fuel consumption display.
Refer to “Information display” on page 3-99.
2. Press and hold the multi-information display switch for
about 5 seconds or more until buzzer sound is heard twice.
3. Press and hold the multi-information display switch to
switch in sequence from “km/L” → “L/100 km” →
“mpg” → “km/L”.
BK0162600US.book 107 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-108 Features and controls
3
NOTE
The display units for the driving range, the average fuel
consumption are changed, but the units for the indicating
needle (speedometer), the odometer, the trip odometer and
the service reminder will remain unchanged.

If the battery is disconnected, the memory of the unit set-
ting is erased and it returns automatically to factory set-
ting.
The distance units is also changed in the following combina-
tions to match the selected fuel consumption unit.
Fuel
consumption
Distance
(driving range)
km/L km
L/100 km km
mpg mile (s)
BK0162600US.book 108 ページ ２０１３年３月２２日　金曜日　午後２時４１分