remove seats MITSUBISHI MIRAGE 2014 6.G Owners Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2014, Model line: MIRAGE, Model: MITSUBISHI MIRAGE 2014 6.GPages: 460, PDF Size: 20.86 MB
Page 47 of 460
Seat and restraint systems
2-21
2
Seat belt extender
N00406700205
If your seat belt is not long enough, even when fully extended,
a seat belt extender must be obtained. The extender may be
used for either of the front seats.
WA R N I N G
!Always adjust the shoulder belt anchor so that the
shoulder belt is positioned across the center of your
shoulder without touching your neck. The shoulder
belt should not be able to fall off your shoulder. Fail-
ure to follow this instruction can adversely affect
seat belt performance and increase the risk of seri-
ous injury or death in the event of an accident.Adjust the shoulder belt anchor only when the vehi-
cle is not in motion.Make sure the anchor is securely locked in position
after adjusting it.
WA R N I N G
!The extender should only be used if the existing belt
is not long enough. Anyone who can use the stan-
dard seat belt should not use an extender. Unneces-
sary use of an extender can adversely affect seat belt
performance in an accident.When not required, the extender must be removed
and stowed.
BK0162600US.book 21 ページ 2013年3月22日 金曜日 午後2時41分
Page 55 of 460
Seat and restraint systems
2-29
2
Examples of child restraint systems compatible with the
LATCH system
N00419000114
Using the LATCH system
N00419100232
1. In order to securely fasten the tether strap, remove the
head restraint from the location where you wish to install
the child restraint system.
2. Open the gap a little between the seat cushion (A) and the
seatback (B) with your hand to locate the lower anchors
(C).
3. Push the anchor connectors (D) on the child restraint sys-
tem into the lower anchors (C) in accordance with the
instructions provided by the child restraint system manu-
facturer.
Remember, the lower anchors provided with your
vehicle are designed to secure suitable child restraint
systems compatible with the LATCH system in the
outboard positions of the rear seats only. The anchor
connectors are NOT designed to secure a suitable child
restraint system in the center position of the rear seat.
A- Rear-facing child restraint system
B- Front-facing child restraint system
C- Child restraint system lower anchor connectors
D- Tether strap
(These are only examples.)
BK0162600US.book 29 ページ 2013年3月22日 金曜日 午後2時41分
Page 69 of 460
Seat and restraint systems
2-43
2
Passenger’s airbag off indicator
N00418100323
The passenger airbag off indicator is located at shown in the
illustration.
The indicator normally comes on when the ignition switch is
turned to the “ON” position or the operation mode is put in
ON, and goes out a few seconds later. In the following situa-
tions, the indicator will stay on to show that the passenger front
airbag is not operational.
The front passenger seat is not occupied.
The system senses that a child is using a child restraint
system on the front passenger seat.
When the passenger’s seat occupant classification sensor sys-
tem senses there is a person seated in the front passenger seat,
the indicator goes out to show that the passenger’s front airbag
is operational.
To ensure that the passenger’s seat occupant classifi-
cation sensor system can sense correctly, observe the
following instructions. Failure to follow these
instructions can adversely affect the performance of
the passenger’s airbag system.
• Adjust the seat to the correct position, and sit well
back against the seatback.
Refer to “Front seats” on page 2-3.
• Do not recline the seatback more than necessary.
• Never have more than one person (adult or child)
sitting on the seat.
• Do not place anything between the seat and the
floor console.
• When attaching a child restraint system, secure it
firmly.
• Do not place luggage or other objects on the seat.
• Do not use a seat cover or a cushion.
• Do not modify or replace the seat and seat belt.
• Do not place luggage or other objects under the
seat.
• Do not place and use an electronic device such as a
computer on the seat.
• Do not place heavy objects on the seat or stick
pins, needles, or other objects into it.
• Do not remove the seat cushion skin.
• If any liquid is spilled on the seat, wipe it and dry
the seat immediately.
If the vehicle is involved in a severe impact, have the
SRS sensors inspected by an authorized Mitsubishi
Motors dealer as soon as possible.
WA R N I N G
!
BK0162600US.book 43 ページ 2013年3月22日 金曜日 午後2時41分
Page 431 of 460
Vehicle care and maintenance
7-57
7
NOTEDo not use cleaners, conditioners, and protectants contain-
ing silicones or wax.
Such products, when applied to the instrument panels or
other parts, may cause reflections on the windshield and
obscure vision.
Also, if such products get on the switches of the electrical
accessories, it may lead to failure of these accessories.Upholstery
N00945500128
1. To maintain the value of your new vehicle, maintain the
upholstery carefully and keep the interior clean.
Use a vacuum cleaner and brush to clean the seats. If
stained, vinyl and synthetic leather should be cleaned with
an appropriate cleaner. Cloth fabrics can be cleaned with
either upholstery cleaner or a 3% solution of gentle soap
in lukewarm water.
2. Clean the carpeting with a vacuum cleaner and remove
any stains with carpet cleaner. Oil and grease can be
removed by lightly dabbing with a clean white cloth and
spot remover.NOTEIf fuzzing is difficult to remove from the seat upholstery,
draw a suitable defuzzing brush over the surface in one
direction.
Genuine leather (if so equipped)
N00945600187
1. To clean, lightly wipe the leather with a soft cloth soaked
in a 5% solution of gentle soap and water.
2. To rinse, dip the cloth in fresh water, wring it out well, and
wipe off all the soap.
3. To preserve and protect, use a leather protecting agent on
the genuine leather surface.NOTEIf genuine leather is wet with water, wipe it with a dry,
soft cloth. If left damp, mildew may grow.
The genuine leather surface can be damaged if brushed
with a nylon or synthetic fiber brush.
Organic solvents such as benzine, kerosene, alcohol, gaso-
line, or acid or alkaline solvents can discolor the genuine
leather surface and should not be used.
Genuine leather can mildew if not kept clean. Clean up
any oil stains immediately.
The genuine leather surface may harden and shrink if it is
exposed to the direct sunlight for long hours. When your
vehicle is parked, place it in the shade as much as possi-
ble.
When the temperature of the vehicle interior rises in sum-
mer, vinyl products left on the genuine leather seat may
deteriorate and stick to the seat.
BK0162600US.book 57 ページ 2013年3月22日 金曜日 午後2時41分