instrument panel MITSUBISHI MONTERO 1987 1.G Workshop Manual

INTRODUCTION - Vehicle Identification
VEHlCLE IDENTIFICATION
“&LE IDENTIFICATION NUMBER LOCATIOyo(lcAmm
The vehicle identification number (V.I.N.) is located on a plate
attached to the left top side of the instrument panel.
VEHICLE lDENTlFlCATlON CODE CHART PLATEo,,.,
All vehicle identification numbers contain 17 digits. The vehicle
number is a code which tells country, make, vehicle type, etc.
Country Make
!
J- A-
Japan Mitsu-
bishi Vehicle
type Line 4-
F- J-
Multi-
4001 Ibs. MON-
purpose or more TERO
vehicle
with
(MPW hydraulic
brakes
7-Truck
6th
digit
Price
class
2- Low
4- High 7th
8th 9th 10th
digit digit digit digit
Body Engine Check Model
digit year
3- E- 0 H-
3-door
2.6 liters 1 1987
metal- (155.9 2 year
top or C.I.D.) 3
van
9
X Plant
1 ZZ-Zer 1
NOTE
*“Check digit” means a single number or letter X used to verify the accuracy of transcription of vehicle indentification
number.
1 STB Revision
1 I : “’

8-20 WIRING HARNESS - How to Read Wiring Diagrams
HOW TO READ WIRING DIAGRAM NOEDBAE
HOW TO READ CONFIGURATION DIAGRAMS
(1) Connector symbols
A wiring diagram shows the installed condition of each connector in a schematic style. The connectors are
shown and classified as follows, depending on their locations and are marked by connector symbols.
In case connectors of the same shape (same number of wires) are centralized, their colors are indicated for
identification.
Examp’e : p.!- f.~~~~ ~;~~o,
Connector’s unique number (serial number)
A : Engine compartment
B : Interior and frame
C : Instrument panel
Main fusible link
A-03
A-o4
> 4WD indicator switch
A-05 Automatic transmission oil
I temperature switch indicates that the connector is located in the
Same connector No. is used in the wiring diagram and the circuit diagram.
I Indicates color of the
A-58 connector. I
1 ST6 Revision

8-32 WIRING HARNESS - Instrument Panel
3 INSTRUMENT PANEL
Connector symbol
C
C-65 c-04
C-06
C-64
C-63
C-61
CL57 C-b6 C!55 d54 c!5
Remarks
For information concerning the ground points (example:
q ),
refer to P.8-7.
C-01 Back door lock switch
C-02 Defogger switch
C-03 Kev reminder and seat belt
warning buzzer
c-04
pi;’ Combination meter
C-08 Diode
C-09 Rear wiper and washer switch
r&~}Oil pressure gauge
C-12 f;hybination gauge illumination
C-l 3 Blower switch
C-14 Combination gauge wiring
harness and front wiring harness
combination
C-15 F;hybination gauge illumination
C,::F}Voltage meter C-l 8 Heater relay
C-l 9 Air conditioner wiring harness
and front wiring harness
combination
E:$)}Air conditioner relay C-31 Blower motor resistor
C-32 Dedicated fuse (Air conditioner
circuit)
C-33 Air conditioner switch
C-34 yl;Jer control lonob illumination
$:;;I Thermostat
$:;;I Feed back carburetor control unit
C-26 Front speaker (R.H.)
C-27 Front wiring harness and roof
wiring harness combination
C-28 Automatic free-wheeling hub
indicator control unit
C-29 Seat belt warning timer
C-30 Front wiring harness and door
wiring harness (R.H.)
combination c-35
C-36
c-37
C-38
c-39
c40
“3’ ‘. Blower switch
Clock
Heater control panel illumination
light
Ashtray illumination light
Air conditioner switch
illumination light
Front wiring harness and center
panel wiring harness
combination
[ STB Revision

WIRING HARNESS - Instrument Panel 8-33
cy50 C149 Cl48 c-47
El$,}Cigarette lightet
C-43 Cigarette lighter illumination light
E::$ Radio
C-46 Shift position illumination light
C-47 Inhibitor switch
C-48 OD-OFF switch
C-49 Parking brake switch
C-50 Seat belt switch
C-51 Hazard switch
E3 Column switch
C-54 Key reminder switch
C-55 Ignition switch
C-56 Stop light switch C-57 Dimmer control switch
C-58 Front wiring harness and door
wiring harness (L.H.) combination
C-59 Turn-signal flasher unit
C-60 Power window relay
C-61 Intermittent wiper relay
C-62 Hazard flasher unit
C-63 OD-OFF relay
C-64 Headlight washer motor relay
C-65 Front speaker (L.H.)
Ision

WIRING HARNESS - Instrument Panel Wumination Circuit 8-51
11 INSTRUMENT PANEL ILLUMINATION CIRCUIT
Battery
Sub fusible link
5-w 0.5-G
5-w l-75-W m 2-R - L-
Main A-23
fusible link
@L
M’ CA
A A-22
Y$lO rx
c-l
Optical fiber
I
I
Multi-purpose
fuse
0
3
a control knob
illumination light
.ight contr
clay
& 01 BY
7t Combination
gauge
Illumination ligl
c-4o1l Shift-position
lmer control switch
C-38
4
Ashtray
illumination Cigaretty Hegpane _
lighter illumination ’ I
minagn light Clock
n+ 63 illumination light Combination meter
illumination light
37w '62; (1) The broken lines are applicable to models equipped with
an automatic transmission.
(2) For information concerning the ground points (exam-
ple: 0 ), refer to P.8-7.
Wiring color code
B: Black Br: Brown G: Green Gr: Gray
LI: Light blue 0: Orange P: Pink R: Red L: Blue
Y: Yellow Lg: Light green
W: White
1 STB Revision

METERS AND GAUGES - Combination Meter 8-135
.3
16WQ25
16W925
10W926
16F554
FUEL GAUGE
Measure the resistance value between t.he terminals by using
an ohmmeter.
Standard value :
l-2 terminals:
2-3 terminals:
l-3 terminals: 23-27 R
122-148 Sz
100-120 IR
Caution
If there is a malfunction of the ground contact of the
voltage regulator even once during vehicle operation,
the excessive current flowing through the heat coil of
the water temperature gauge and the fuel gauge will
cause permanent distortion of the bimetal, resulting in
the indications being consistently lower than the actual
value.
For this reason, therefore, be sure to make the earth
contact securely.
WATER TEMPERATURE GAUGE
Measure the resistance value between the terminals by using
an ohmmeter.
Standard value:
Bimetal type
l-2 terminals: 50-80 n
SERVICE POINTS OF INSTALLATION
2. INSTALLATION OF SPEEDOMETER CABLE
Insert the cable until its stopper properly fits to the
speedometer groove.
Caution
Poor installation of the cable may cause a fluctuating
meter pointer, or noise and a damaged harness inside
the instrument panel.
) STB Revision

METERS AND GAUGES - s-meter Unit 8-139
Center shaft of
pitching damper plate
Pointer
16W 600
Spherical dial
Spherical
horizontal
16W966
Spherical dial Dial support plate
/ Oil case
Gxizontal centerlinewtationaryframe
Blind plate
16W627
;ide to side inclination Forward or backwarc
Hokizontal line Horizbntal line
INCLINOMETER
OUTLINE
The inclinometer is an instrument which indicates the forward
or backward inclination (pitching) or side to side inclination
(ding) of vehicle.
Motion of a pendulum in the system is displayed on the
system. The pitching and rolling pointer is supported by a
double support mechanism in which the rolling fulcrum is
supported in such a way as to be rotative around the case and
the pitching fulcrum supported on the rolling system
CONSTRUCTION
The inclinometer consists of an outer case which inclines with
the vehicle, a pointer which is provided in an oil case and
always maintains a level position, and a spherical dial. The
spherical dial is coupled through the dial support plate to the
rolling damper plate. The rolling damper plate is swivel bearing
coupled to a stationary frame by the center axis, so it can
incline side-to-side, but is always held in a level position by a
pendulum. The pointer is coupled with the pitching damper
plate.
Since the pitching damper plate is swivel bearing coupled to
the rolling damper plate by the center axis, it can incline
forward and backward, but is always maintained in a level
position by the pendulum.
OPERATION
The side-to-side inclination angle should be read on a scale of
the front panel as indicated by the horizontal centerline of the
spherical dial, whereas the forward or backward inclination
angle should be read on a scale of the spherical dial as
indicated by the pointer.
[ STB Revision

8-148 LIGHTING SYSTEM -Troubleshooting
STOP LIGHT
The stop light fails to illuminate
The stop light does not go off
The stop light on one side does not illuminate
NOTE
Number in circle indicates inspection sequence
INSTRUMENT PANEL ILLUMINATION CIRCUIT
Inspection iterns
Symptom
Illumination light fails to illuminate (the tail light also fails to illuminate)
Illumination light fails to illuminate (the tail light illuminates)
Illumination light cannot be dimmed 0
a A
0
0 Other inspection
items
0 Installation parts
of the stop light
switch
1 STB Revision
-1

8-156 LIGHTING SYSTEM - Circuit Diagram
CIRCUIT DIAGRAM
INSTRUMENT PANEL ILLUMINATION CORCUIT
-1.25-B-
0
.5-w 0.5-G
2-R
Battery
-Err
5-w 15-w r
Main ’ A-02 A-23
Sub fusible link
fusible link a
I
z N
A A-22 [
cy]llo CY
c-i
Optical fiber
I
Multi-purpose
fuse Heater
control knob
illumination light Heater
control knob
ght control
lay Combination
gauge B 01 0’
Illumination light
/ n
c
C
-
c-57 0 ti
Q BY Lighting
switch
Dimmer control switch
rel
Combination meter
illumination light illumination lighter
Remarks
(1) The broken lines are applicable to models eouipped with
37W822 an automatic transmission.
(2) For information concerning the ground points (exam-
ple: 0 1, refer to P.8-7.
Wiring color code
6: Black
Br: Brown G: Green
Ll: Light blue Gr: Gray
0: Orange P: Pink
R: Red L: Blue
Y: Yellow Lg: Light green
W: White 1 ST6 Revision

LIGHTING SYSTEM - Hazard Warning Switch 8-161
HAZARD WARNING
REMOVAL AND INSTALLATION NOBICLAC
16W1531
SERVOCE POINTS OF REMOVAL
1. HAZARD WARNING SWITCH
Insert the special tool into the switch and pry the switch to
remove it from the instrument panel.
INSPECTION
Operate the switch and check the continuity between the ter-
minals.
NOTE
CC indicates that there is continuity between the terminals.
STB Revision