wheel torque MITSUBISHI MONTERO 1991 User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 270 of 1333
![MITSUBISHI MONTERO 1991 User Guide PROBLEM
Possible Cause Action
\
\
\
\
\
\](/img/19/57332/w960_57332-269.png "MITSUBISHI MONTERO 1991 User Guide PROBLEM
Possible Cause Action
\
\
\
\
\
\")
PROBLEM
Possible Cause Action
\
\
\
\
\
\
\
GREASE LEAKING
Ripped CV Boot ................................... Replace Boot
CLICKING NOISE WHILE CORNERING
Dry/Worn CV Joints .................... Replace Outer CV Joints
CLUNK ON ACCELERATION
Dry/Worn CV Joints .................... Replace Inner CV Joints
Worn Trans. Gears/Bearings ..................... Inspect Trans.
VIBRATION/SHUDDER ON ACCELERATION
Dry/Worn CV Joints .......................... Replace CV Joints
Alignment Out ................................. Check Alignment
Incorrect Spring Height ................... Check Spring Height
SQUEALING OR HUMMING
Dry/Worn CV Joints ..................... Lube/Replace CV Joints
Faulty Wheel Bearing .................... Replace Wheel Bearing
\
\
\
\
\
\
\
TESTING & INSPECTION
AXLE SHAFT END PLAY
Using dial indicator, check axle shaft end play. End play
must be .0020-.0079" (.05-.20 mm). If end play is not within
specification, change shims to obtain correct end play. See AXLE
SHAFTS under REMOVAL & INSTALLATION.
AXLE TOTAL BACKLASH
1) Raise and support rear axle. Place transmission in
Neutral. Apply parking brake. Rotate drive shaft clockwise. Place
reference marks on pinion dust cover and differential housing.
2) Rotate drive shaft counterclockwise and measure distance
between reference marks. Differential must be removed and backlash
adjusted if distance exceeds 0.2" (5.0 mm).
LIMITED SLIP DIFFERENTIAL PRELOAD
1) Place transmission in Neutral. Block front wheels. Raise
one rear wheel free of ground and remove wheel. Use Axle Puller
Adapter (MB990241) for Montero and Pickup models. Install adapter on
wheel studs. Release parking brake.
2) Using torque wrench, measure starting torque on Pickup
models while rotating wheel in forward direction. On Montero models,
measure rotating torque. This measurement is read once axle is
turning. Differential must be repaired if torque is less than
specification. See TESTING SPECIFICATIONS table.
Page 284 of 1333
![MITSUBISHI MONTERO 1991 User Guide runout.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\](/img/19/57332/w960_57332-283.png "MITSUBISHI MONTERO 1991 User Guide runout.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\")
runout.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Axle Bearing Lock Nut (Montero) .................. 130-159 (176-216\
)
Bearing Cap Bolt ..................................... 40-47 (54-64)\
Bearing Case-To-Axle Housing Bolt .................... 36-43 (49-58)\
Brake Tube Flare Nut ................................. 10-12 (14-16)\
Differential Carrier-To-Axle Housing Nut
2.4L (2WD) ......................................... 18-22 (24-30\
)
3.0L (4WD) ......................................... 29-40 (39-54\
)
Drain Plug ........................................... 43-50 (58-68)\
Filler Plug .......................................... 29-43 (39-58)\
Lock Plate Bolt ...................................... 11-16 (15-22)\
Pinion Flange Nut ................................ 137-181 (186-245)\
Drive Shaft-To-Flange Bolt ........................... 36-43 (49-58)\
Ring Gear Bolt ....................................... 58-65 (79-88)\
Side Bearing Lock Plate Bolts ........................ 11-16 (15-22)\
Wheel Lug Nut
Montero ........................................... 72-87 (98-118)\
Pickup .......................................... 87-101 (118-137)\
\
\
\
\
\
\
\
Page 290 of 1333
FLANGES
FLEX PLATES
FLUID LEVEL INDICATORS
FLUIDS AND LUBRICANTS
FLYWHEELS
FORCE MOTORS
GUIDES
HALF SHAFTS
HOSES, LINES AND TUBES
HOUSINGS (BELL, CASE, TAIL (EXTENSION) AND AUXILIARY)
INTERMEDIATE SHAFT SUPPORT BEARINGS
KEY INTERLOCK SYSTEMS
LIMITED SLIPS
LINES
LINKAGES (EXTERNAL)
LOCKING HUB ASSEMBLIES
LOCKING HUB CONTROL KNOBS
LUBRICANTS
METAL-CLAD SEALS
METALASTIC JOINTS
MODULATOR PINS
MODULATORS
MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION)
ODOMETER DRIVES (MECHANICAL)
ODOMETER HEADS (MECHANICAL)
OIL PANS
PANS
PILOT HOLES
PRESSURE PLATES
PRESSURE SWITCHES
RACES
RUBBER JOINTS (METALASTIC)
SCREENS
SEALS
SEALS (METAL-CLAD)
SELECTOR INTERLOCK SYSTEMS
SERVOS
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS)
SENSORS
SIDE COVERS
SLIP YOKES
SOLENOIDS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
SPEEDOMETER-DRIVEN GEAR HOUSINGS
SPEEDOMETER/ODOMETER DRIVES (MECHANICAL)
SPEEDOMETER/ODOMETER HEADS (MECHANICAL)
SPEEDOMETERS AND ODOMETERS (ELECTRONIC)
SWITCHES
TONE WHEELS
TOOTHED RINGS (TONE WHEELS)
TORQUE CONVERTERS
TRANSAXLE MOUNTS
TRANSDUCERS (TRANSMISSION)
TRANSMISSION COOLERS
TRANSMISSION MOUNTS
TRANSMISSION PANS
TRANSMISSION RANGE INDICATORS (PRNDL)
TUBES
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
VACUUM CONTROLS
VACUUM HOSES
VACUUM MOTORS
VACUUM-OPERATED SWITCHES
Page 327 of 1333
![MITSUBISHI MONTERO 1991 User Guide VENT INSPECTION \
\
\
\
\
\
\
Condition Code](/img/19/57332/w960_57332-326.png "MITSUBISHI MONTERO 1991 User Guide VENT INSPECTION \
\
\
\
\
\
\
Condition Code")
VENT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A ............ Require replacement.
Missing ................. C ............ Require replacement.
Plugged ................. A ........... (1) Require repair or
replacement.
( 1) - A plugged vent may force fluid past the seal.
\
\
\
\
\
\
\
VIBRATION DAMPERS
VIBRATION DAMPER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A ............ Require replacement.
Missing ................. C ............ Require replacement.
Out of position ......... B .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
WHEEL ATTACHMENT HARDWARE
NOTE: For conditions noted below, also check conditions of
wheel stud holes.
CAUTION: Proper lug nut torque is essential. Follow recommended
torque specifications and tightening sequence. DO NOT
lubricate threads unless specified by the vehicle
manufacturer.
WHEEL ATTACHMENT HARDWARE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Bent .................... A ............ Require replacement.
Broken .................. A ........ ( 1) Require replacement.
Loose ................... B ... Require repair or replacement
of affected component.
Lug nut installed
backward ............... B .. Require repair or replacement.
Lug nut mating surface
dished ................. A ..... Require replacement of nut.
Lug nut mating type
incorrect .............. B ..... Require replacement of nut.
Lug nut rounded ......... A . ( 2) Require replacement of nut.
Lug nut seized .......... A . ( 2) Require replacement of nut.
Stud incorrect .......... B .... Require replacement of stud.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Some manufacturers require replacement of all studs on
that wheel if two or more studs or nuts on the same wheel
are broken or missing.
( 2) - Only required if removing wheel.
\
\
\
\
\
\
\
Page 623 of 1333
Torque Converter Clutch Solenoid/Switch ......... Engine Performance
Traction Control Switch ........................... Anti-Lock Brakes
Trailer Tow Connector .............................. Exterior Lights
Trailer Tow Relay .................................. Exterior Lights
Transmission/Transaxle .......................... Engine Performance
Transmission Control Module (TCM) ............... Engine Performance\
Starters
Transmission Range Sensor ................................. Starters
Back-Up Lights
Engine Performance
Transmission Range Switch ........................... Back-Up Lights
Engine Performance
Anti-Theft System
Turn Signal Flasher ................................ Exterior Lights
Turn Signal Lights ................................. Exterior Lights
Twilight Sentinel Switch ......................... Headlight Systems
Daytime Running Lights
Vapor Canister Leak Detection Pump .............. Engine Performance
Vehicle Control Module (VCM) .................... Engine Performance\
Vehicle Dynamic Module ....................... Electronic Suspension
Vehicle Speed Control Servo ................. Cruise Control Systems
Vehicle Speed Sensor .......................... Data Link Connectors
Analog Instrument Panels
Cruise Control Systems
Electronic Suspension
Voltage Regulator .......................... Generators & Regulators
Water-In-Fuel Sensor ............................ Engine Performance
Analog Instrument Panels
Wheel Speed Sensors ............................... Anti-Lock Brakes
Window Timer Module .......................... Power Convertible Top
Windshield Intermittent Wiper Relay ........... Wiper/Washer Systems
Windshield Washer Motor ....................... Wiper/Washer Systems
Wiper Motor ................................... Wiper/Washer Systems
\
\
\
\
\
\
\
Page 684 of 1333
\003
PR E-A LIG NM EN T C HEC KS
1991 M it s u bis h i M onte ro
Wheel Alignment
PRE-ALIGNMENT INSPECTION PROCEDURES
PRE-ALIGNMENT CHECKS
Before making wheel alignment adjustment, perform the
following checks:
1) Tires should be equal in size and runout must not be
excessive. Tires and wheels should be in balance, and inflated to
manufacturer's specifications.
2) Wheel bearings must be properly adjusted. Steering linkage
and suspension must not have excessive looseness. Check for wear in
tie rod ends and ball joints.
3) Steering gear box must not have excessive play. Check and
adjust to manufacturer's specifications.
4) Vehicle must be at curb height with full fuel load and
spare tire in vehicle. No extra load should be on vehicle.
5) Vehicle must be level with floor and with suspension
settled. Jounce front and rear of vehicle several times and allow it
to settle to normal curb height.
6) If steering wheel is not centered with front wheels in
straight-ahead position, correct by shortening one tie rod adjusting
sleeve and lengthening opposite sleeve equal amounts.
7) Ensure wheel lug nuts are tightened to torque
specifications.
Page 693 of 1333
intake hoses and EGR pipe. Disconnect oxygen sensor electrical
connector.
2) Remove oil pipe and EGR valve. Disconnect exhaust fitting
and remove rear heat protector. Remove oil return pipe. Remove
turbocharger assembly. See Fig. 11.
Fig. 11: Removing Rear Turbocharger (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Inspection
Check turbine and compressor wheels for cracking and other
damage. Make sure turbine and compressor wheels turn smoothly. Check
for oil leakage from turbocharger assembly. Check for proper wastegate
valve operation. See SYSTEM & COMPONENT TESTING article.
Installation
1) To install, reverse removal procedure. Before oil pipe
flare nut (above turbocharger) is installed, pour clean engine oil
into turbocharger. Ensure oil and air hoses are properly installed and
securely clamped.
2) Use new gaskets. Adjust accelerator cable (if necessary).\
Refill engine oil and coolant. Check for oil and coolant leaks.
Tighten all bolts to specification. See TORQUE SPECIFICATIONS table.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Applications Ft. Lbs. (N.m)
Fuel Tank Nuts ............................. 15-22 (20-30)
Page 766 of 1333
LOWER BALL JOINT
Place ball joint in soft-jawed vise. Install dial indicator,
with stem resting on end of ball joint stud. Measure ball joint stud
end play. Replace ball joint if end play exceeds .02" (.5 mm).
UPPER BALL JOINT
1) With ball joint disconnected from steering knuckle, place
nut on ball joint stud. Using INCH lb. torque wrench, measure starting
torque required to rotate ball joint stud.
2) Starting torque must be 7-30 INCH lbs. (.8-3.4 N.m). If
starting torque is not within specification, replace ball joint
(Montero) or upper arm (Ram-50 and Pickup). For ball joint replaceme\
nt
on Montero, see UPPER BALL JOINT under REMOVAL & INSTALLATION.
WHEEL BEARINGS ADJUST
PRELOAD
1) Remove locking hub assembly. See LOCKING HUB under REMOVAL
& INSTALLATION. Remove lock washer-to-lock nut bolts and lock washer.
Remove brake caliper to ensure brake pads are not contacting rotor.
2) Using Socket (MB990954-01) and torque wrench, rotate fron\
t
hub and tighten lock nut to 95-145 ft. lbs. (129-197 N.m) to seat
bearings. Loosen nut.
3) Retighten nut to 18 ft. lbs. (24 N.m) and loosen 30-40
degrees. After setting preload, check hub turning resistance and axial
play.
HUB TURNING RESISTANCE & AXIAL PLAY
1) Using INCH lb. torque wrench or spring scale attached to
wheel stud, measure hub turning resistance. Turning resistance should
be 1-4 lbs. (.45-1.8 kg) if measured with spring scale or 2.6-11.3
INCH lbs. (.3-1.3 N.m) if measured with torque wrench.
2) Using dial indicator, check front hub axial play. Axial
play should be .002" (.05 mm) or less. Adjust wheel bearing so turning\
resistance and axial play are within specification. If turning
resistance and axial play cannot be adjusted to specifications, check
wheel bearing condition and installation. Install lock washer.
3) If lock washer and lock nut holes are not aligned, align
holes by loosening lock nut a maximum of 40 degrees. Install lock
washer bolts to lock nut. Tighten lock washer bolts. Install locking
hub.
LOWER BALL JOINT R & I
REMOVAL
1) Raise and support vehicle. Remove wheel assembly. Support
lower control arm enough to release torsion bar tension. Loosen but DO
NOT remove lower ball joint-to-steering knuckle nut.
2) Using ball joint separator, separate ball joint from
steering knuckle. Remove ball joint nut from steering knuckle. Remove
ball joint-to-lower control arm bolts. Remove ball joint.
INSTALLATION
Page 767 of 1333
Lubricate ball joint with SAE J310 NLGI No. 2 grease. Apply
semi-drying sealant to ball joint grooves. Reverse removal procedure
to complete installation. Tighten bolts to specification. See TORQUE
SPECIFICATIONS table at end of article.
NOTE: On Ram-50 and Pickup, replace upper control arm if ball
joint is defective.
UPPER BALL JOINT R & I (MONTERO)
REMOVAL
Remove snap ring and dust cover together from ball joint. See
Fig. 1 . Use Ball Joint Remover/Installer (MB990799-01 and MB990800-01)
and Clamp (MB990840-01) to press ball joint from control arm. Tighten
clamp to remove ball joint.
INSTALLATION
1) Before installing, align reference mark on ball joint with
center of control arm. Using bushing remover/installers, install ball
joint in control arm. See Fig. 1.
2) Install snap ring on ball joint. Lubricate ball joint with
SAE J310 NLGI No. 2 grease. Apply semi-drying sealant to ball joint
grooves. Install new dust cover and ring.
AUTOMATIC TYPE LOCKING HUB R & I
REMOVAL
1) Place hub must in the FREE position by placing transfer
case lever in 2H position and moving vehicle in Reverse approximately
4-6 feet.
2) Remove cover from locking hub. If necessary, wrap shop
towel around cover and use an oil filter wrench to loosen cover. Raise
and support vehicle. Remove wheel assembly.
3) Using snap ring pliers, remove snap ring and shim from end
of drive axle. See Fig. 2. Using hexagonal wrench, remove locking hub
retaining bolts. Remove locking hub assembly.
Fig. 2: Exploded View of Automatic Locking Hub
Courtesy of Chrysler Motors.
INSTALLATION
Page 768 of 1333
1) Using Socket (MB990954) and torque wrench, rotate front
hub and tighten lock nut to 95-145 ft. lbs. (129-197 N.m) to seat
bearings. Loosen nut. Retighten nut to 18 ft. lbs. (24 N.m) and loosen\
30-40 degrees.
2) Using spring scale attached to wheel stud, measure and
record turning resistance required to rotate hub/rotor assembly before
installing locking hub.
3) Apply semi-drying sealant on locking hub assembly-to-
hub/rotor contact areas. DO NOT apply sealant on outer areas of
hub/rotor assembly, toward brake contact areas.
4) Align locking hub assembly key area with steering knuckle
keyway area. Loosely install locking hub assembly on hub/rotor
assembly. Ensure locking hub assembly fully contacts hub/rotor
assembly.
5) Install locking hub retaining bolts. Tighten to
specification. See TORQUE SPECIFICATIONS table at end of article.
Using spring scale attached to wheel stud, measure turning resistance
required to rotate hub/rotor assembly.
6) Subtract turning resistance measured in step 2) (before
installing locking hub) from turning resistance measured in step 5)
(after installing locking hub). If difference exceeds 3.1 lbs. (14 N)\
,
check for incorrect installation of locking hub assembly or
components.
7) Install shim and snap ring on drive axle. Rotate drive
axle until maximum end play is obtained. Using dial indicator, check
drive axle end play.
8) Drive axle end play should be .008-.020" (.20-.51 mm). If\
end play is not within specification, adjust drive axle end play by
changing axle shaft shim. Install new "O" ring and cover. Tighten
cover to specification. See TORQUE SPECIFICATIONS table at end of
article.
LOWER CONTROL ARM R & I
REMOVAL
1) Raise and support vehicle. Remove wheel assembly. Remove
front skid plate and undercover (if equipped). Remove torsion bar. See\
TORSION BAR under REMOVAL & INSTALLATION. Remove stabilizer bar bolt
from control arm.
2) Remove shock absorber-to-control arm bolts. Loosen but DO
NOT remove lower ball joint-to-steering knuckle nut. Using ball joint
fork, separate lower ball joint from steering knuckle.
3) Remove ball joint stud nut from steering knuckle. Remove
control arm shaft. See Fig. 1. Remove torque arm. Remove lower control
arm pivot bolt. Remove lower control arm.
INSPECTION
1) Inspect control arm for cracks or deformation. Check ball
joints. See BALL JOINT CHECKING under ADJUSTMENTS & INSPECTION.
2) Inspect ball joint dust covers for damage. Replace dust
covers if damaged. Inspect control arm bushing and frame bracket
bushing for damage. Replace if necessary.
3) If frame bracket bushing needs replacing, install Bushing
Remover/Installer (MB990958-01) in bushing. See Fig. 3. Tighten
bushing remover/installer bolt until bushing is removed. Reverse
bushing remover/installer to install bushing.
NOTE: Differential carrier may require relocation to replace left
bracket bushing.