wheel torque MITSUBISHI MONTERO 1991 Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 771 of 1333
REMOVAL
Remove skid plate (if equipped). Remove stabilizer bar bolt
from lower control arm. Remove stabilizer bar clamp-to-hanger bolts.
Remove stabilizer bar and bushings. Remove stabilizer bar-to-frame
hangers (if necessary).
INSTALLATION
Inspect bushings for wear. Check stabilizer bar for
deformation. To install, reverse removal procedure. Install stabilizer
bar-to-frame hangers and stabilizer bar-to-control arm bolt using new
nuts. Tighten hanger-to-frame nut and stabilizer bar-to-control arm
nut until distance from threaded end of bolt to nut is .24-.32" (6.1-
8.1 mm).
STEERING KNUCKLE R & I
REMOVAL
1) Raise and support vehicle. Remove wheel assembly. Remove
brake caliper. Remove hub/rotor assembly. See WHEEL BEARINGS under
REMOVAL & INSTALLATION. Remove dust cover from steering knuckle.
2) Disconnect tie rod end from steering knuckle. Loosen
torsion bar anchor arm assembly adjusting nut. Loosen ball joint-to-
steering knuckle nuts. Using ball joint separator, separate ball
joints from steering knuckle.
3) Detach upper and lower ball joints from steering knuckle.
Remove steering knuckle from drive axle. Remove oil seal and spacer
from steering knuckle.
INSPECTION
Inspect steering knuckle for cracks. Inspect spindle and
steering knuckle needle bearing for wear or damage.
INSTALLATION
1) If needle bearing requires replacement, drive bearing from
steering knuckle. Use Bearing Driver (MB990956-01) and Handle
(MB9909938-01) to install needle bearing.
NOTE: DO NOT reuse steering knuckle bearing if removed.
2) Using bearing installer and handle, install new needle
bearing until bearing is even with steering knuckle end face. Apply
SAE J310 NLGI No. 2 grease to bearing roller surface and spacer-to-
steering knuckle contact areas. Install spacer with chamfered side
toward inside of vehicle.
3) Using Seal Installer (MB990985-01) and Handle (MB990938-\
01), install seal in steering knuckle until seal is even with steering
knuckle end face. Apply grease to seal lip area and inside of seal. To
complete installation, reverse removal procedure. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table at end of article.
TORSION BAR R & I
CAUTION: Mark torsion bar and anchor arm location for reassembly
reference before removing.
Page 774 of 1333
UPPER CONTROL ARM R & I
REMOVAL
1) Remove shock absorber. Support lower control arm with jack
stand. Remove wheel assembly. Loosen anchor bolt lock nut. See Fig. 1.
2) Mark anchor bolt for reassembly reference. Loosen anchor
bolt to release torsion bar tension. Disconnect and plug brake hose at
frame mount bracket. Remove cotter pin from ball joint stud. Loosen
but DO NOT remove ball joint stud knuckle nut.
3) Using ball joint fork, loosen ball joint from steering
knuckle. Remove ball joint stud nut. Remove rebound stopper and brake
hose support from control arm. Remove upper control arm mounting
bolts. Note direction of bolt installation and location of camber
adjustment shims. Remove control arm.
4) If clearance is inadequate for control arm removal, move
control arm toward rear of vehicle and pull out front part of arm.
Rotate control arm pivot shaft and remove arm. If arm still cannot be
removed, loosen 10 front body mounting nuts. Raise body and remove
arm.
NOTE: On Montero, rotating control arm shaft will alter caster
setting.
INSPECTION
1) Inspect control arm for cracks or deformation. On Montero,
mount control arm in soft-jawed vise using control arm shaft. Attach
spring scale to upper end of control arm, near ball joint.
2) Using spring scale, measure starting torque required to
rotate control arm on the shaft. Replace control arm if starting
torque exceeds 1.4 lbs. (6.5 N).
3) On all models, check ball joints. See BALL JOINT CHECKING
under ADJUSTMENTS & INSPECTION. Inspect ball joint dust cover for
damage and replace as necessary.
INSTALLATION
1) To install, reverse removal procedure. On Montero, ensure
control arm shaft is correctly positioned before installing. Rotate
control arm shaft to obtain correct measurement. See Fig. 6.
Fig. 6: Positioning Upper Control Arm Shaft (Montero)
Courtesy of Mitsubishi Motor Sales of America.
2) On Ram-50 & Pickup, install control arm-to-crossmember
bolts from the inside of crossmember, with nuts against control arm
Page 775 of 1333
shaft.
3) On Montero, install control arm-to-crossmember bolts from
the outside of control arm, with nuts against crossmember.
4) Ensure alignment shims are placed in original location.
When installing shock absorber, ensure White paint mark on lower end
of shock faces toward the outside of vehicle. Tighten shock absorber
upper nut until distance from end of threads to nut is .27-.31" (7-8
mm). Install shock lock nut.
5) Tighten bolts to specification. See TORQUE SPECIFICATIONS
table at end of article. Bleed brakes. Adjust anchor bolt to proper
torsion bar setting. See TORSION BAR under REMOVAL & INSTALLATION.
Check wheel alignment and adjust if necessary.
WHEEL BEARINGS R & I
REMOVAL
1) Raise and support vehicle. Remove wheel assembly. Remove
caliper assembly. Remove locking hub. See LOCKING HUB under REMOVAL &
INSTALLATION.
2) Remove lock washer. Using Socket (MB990954), remove lock
nut. Remove front hub assembly from steering knuckle.
3) Remove oil seal and bearings from hub. If bearing races
need to be replaced, drive bearing races from hub using brass drift
and hammer.
INSTALLATION
1) Before installing, lubricate outside surfaces of bearing
outer races with grease. Install bearing outer races in hub. Ensure
bearing races are fully seated.
2) Pack bearings with grease. Install inner bearing in hub.
On Montero, install seal in hub using Seal Installer (MB990955). On
Pickup, use Seal Installer (MB990985).
3) Install seal until seal is even with hub surface. To
complete installation, reverse removal procedure. Adjust wheel
bearings. See WHEEL BEARINGS under ADJUSTMENTS & INSPECTION. Tighten
bolts to specification. See TORQUE SPECIFICATIONS table.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
Application Ft. Lbs. (N.m)
Anchor Bolt Lock Nut ............. 29-36 (39-49)
Automatic Hub Cover .............. 13-25 (18-34)
Ball Joint Nut
Lower ....................... 87-130 (118-176)
Upper .......................... 43-65 (58-88)
Ball Joint-to-Lower
Control Arm Bolt ............... 39-54 (53-73)
Caliper Bolt ..................... 58-72 (79-98)
Control Arm-to-Frame Bolt
Lower ................. ( 1) 101-116 (137-157)
Upper ......................... 72-87 (98-118)
Locking Hub-to-Hub/Rotor Bolt .... 36-43 (49-58)
Manual Hub Cover Bolt .................. 10 (14)
Shock Absorber Lower Mount Bolt
Montero ........................ 11-16 (15-22)
Ram-50 & Pickup ...................... 10 (14)
Page 824 of 1333
(chunking),
exposing cord .......... A ............ Require replacement.
Tread missing pieces
(chunking), not
exposing cord .......... 1 ............ Suggest replacement.
Tread separations A ............ Require replacement.
Tube in tubeless tire 3 .... (4) Suggest removal of tube.
Weather-checking ........ .. ......... No service required or
suggested.
Worn to tread wear
indicators ............. B ............ Require replacement.
( 1) - Determine and correct cause of irregular tire wear.
( 2) - If radials and bias or bias-belted ply tires are on the
same vehicle, the radials must be on the rear axle,
except for high-pressure temporary spares.
( 3) - Excessive is defined as enough to contribute to
performance problems. Match mounting may correct
run-out. If not, require replacement of appropriate
part. Refer to manufacturer's specifications.
( 4) - Most manufacturers do not recommend tubes in tubeless
tires. Inspect tire and wheel assembly to determine
the reason for a tube in tubeless tire. Recommendation
for repair or replacement should be based upon condition
of tires and/or wheel listed in these guidelines.
\
\
\
\
\
\
\
VALVE STEMS
VALVE STEM INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent .................... 1 ........... Suggest replacement.
Broken .................. A ........... Require replacement.
Cut, but not leaking .... 1 ........... Suggest replacement.
Deteriorated
(cracking, dry rot) .... 1 ........... Suggest replacement.
Leaking ................. A . Require repair or replacement.
Missing ................. C ........... Require replacement.
Threads damaged ......... A . Require repair or replacement.
Threads stripped ........ A ........... Require replacement.
Valve cap missing ....... C .... Require replacement of cap.
Weather-checking ........ 1 ........... Suggest replacement.
Won't take air .......... A . Require repair or replacement.
\
\
\
\
\
\
\
WHEEL ATTACHMENT HARDWARE
For conditions noted below, also check conditions of wheel
stud holes.
CAUTION: Proper lug nut torque is essential. Follow recommended
torque specifications and tightening sequence. DO NOT
lubricate threads unless specified by the vehicle
manufacturer.
WHEEL ATTACHMENT HARDWARE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Bent .................... A ............ Require replacement.
Broken .................. A ........ ( 1) Require replacement.
Page 1170 of 1333
\003
TR AN SM IS SIO N R EM OVA L & IN STA LLA TIO N - A /T
1991 M it s u bis h i M onte ro
1991 92 TRANSMISSION SERVICING
Transmission Removal & Installation
Mitsubishi: Eclipse, Galant, Mirage, Montero,
Pickup, Precis, 3000GT
MANUAL
NOTE: For manual transmission/transaxle replacement procedures,
see appropriate article in CLUTCHES.
AUTOMATIC FWD MODELS
REMOVAL
1) Remove battery and battery tray. On 3000GT, remove
undercover(s). On Eclipse turbo, drain and remove intercooler. On all
models, remove air cleaner and case. Raise and support vehicle. Remove
wheels. Disconnect control cables at transaxle. Drain transaxle fluid.
2) On Mirage 1.6L, disconnect tension rod. On all models,
disconnect neutral safety switch connector, oil cooler hoses and
electrical connectors from transaxle. Disconnect speedometer cable and
throttle control cable (if equipped). Remove starter motor.
3) On Galant models with electronically controlled
suspension, remove air compressor and bracket. Disconnect front height
sensor rod at lower control arm.
4) On all models, remove upper transaxle-to-engine bolts.
Remove engine undercover (if equipped). On all models, remove drive
axle shafts. See FWD AXLE SHAFTS article in DRIVE AXLES. Separate
lower control arms from struts for access to axle shafts (if
necessary).
5) Remove front exhaust pipe (if necessary). On Eclipse 4WD,\
Galant 4WD and 3000GT, remove right member and gusset. On 4WD models,
separate transfer assembly from transaxle. Reference mark transfer
assembly-to-drive shaft and remove transfer assembly.
6) On all models, remove transmission inspection (dust)
cover. Place index mark on torque converter and drive plate for
reassembly reference. Remove torque converter-to-drive plate bolts.
Push torque converter away from engine into transaxle.
7) Support transaxle with jack. Remove transaxle mounts
bolts, mounting brackets and remaining transaxle-to-engine bolts.
Slide transaxle assembly to right and lower to remove.
CAUTION: Ensure torque converter is fully seated in transaxle before
installation. Always install new snap rings on inner
constant velocity joints.
INSTALLATION
1) To install, reverse removal procedure. Tighten transaxle-
to-engine bolts and torque converter-to-drive plate bolts to
specification. See TORQUE SPECIFICATIONS table at end of article.
2) Ensure reference marks on torque converter-to-drive plate
and transfer assembly-to-drive shaft align. Tighten mounting bolts
with weight of engine and transaxle on mounts. Refill transaxle fluid
to specified level. Adjust all control cables.
RWD MODELS
Page 1207 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual ENGINES \
\
\
\
\
\
\](/img/19/57332/w960_57332-1206.png "MITSUBISHI MONTERO 1991 Owners Manual ENGINES \
\
\
\
\
\
\")
ENGINES \
\
\
\
\
\
\
High Oil Improper grade of oil Replace with proper oil
Pressure Oil pressure relief valve Eliminate binding
stuck closed
Oil pressure sender or Replace sender or gauge
gauge faulty
\
\
\
\
\
\
\
Noisy Main Inadequate oil supply Check oil delivery to
Bearings main bearings
Excessive main bearing Replace main bearings,
clearance See ENGINES
Excessive crankshaft end Replace crankshaft, See
play ENGINES
Loose flywheel or torque Tighten attaching bolts
converter
Loose or damaged vibration Tighten or replace
damper vibration damper
Crankshaft journals Re-grind crankshaft
out-of-round journals
Excessive belt tension Loosen belt tension
\
\
\
\
\
\
\
Noisy Connecting Excessive bearing clearance Replace bearing, See
Rods or missing bearing ENGINES
Crankshaft rod journal Re-grind crankshaft
out-of-round journal
Misaligned connecting rod Remove rod or cap and
or cap realign
Incorrectly tightened rod Remove and re-tighten
bolts rod bolts
\
\
\
\
\
\
\
Noisy Pistons Excessive piston-to-bore Install larger pistons,
and Rings clearance See ENGINES
Bore tapered or out-of-round Rebore block
Piston ring broken Replace piston rings,
See ENGINES
Piston pin loose or seized Replace piston pin, See
ENGINES
Connecting rods misaligned Realign connecting rods
Ring side clearance too Replace with larger or
loose or tight smaller rings
Carbon build-up on piston Remove carbon
\
\
\
\
\
\
\
Noisy Valve Worn or bent push rods Replace push rods, See
Train ENGINES
Worn rocker arms or bridged Replace push rods, See
pivots ENGINES
Dirt or chips in valve Remove lifters and
lifters remove dirt/chips
Excessive valve lifter Replace valve lifters,
leak-down See ENGINES
Valve lifter face worn Replace valve lifters,
See ENGINES
Broken or cocked valve replace or reposition
springs springs
Too much valve stem-to-guide Replace valve guides,
clearance See ENGINES
Valve bent Replace valve, See
ENGINES
Loose rocker arms Retighten rocker arms,
See ENGINES
Excessive valve seat Reface valve seats, See
run-out ENGINES
Page 1302 of 1333
toe-in is not within specification, remove clips. Turn tie rods or
turnbuckles the same amount, but in opposite directions. Recheck toe-
in.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
\
Application Ft. Lbs. (N.m)
Shock Absorber-To-Crossmember Nut
Montero, Pickup & Ram-50 ............ 10-13 (14-18)
Shock Absorber-To-Lower Arm Bolt
Montero ............................. 11-16 (15-22)
Pickup & Ram-50 ........................... 10 (14)
Upper Arm Shaft To Crossmember
Montero, Pickup & Ram-50 ........... 72-87 (98-118)
Wheel Lug Nut
Colt Vista
Aluminum Wheels ................... 65-80 (88-108)
Steel Wheels ....................... 50-57 (68-77)
Eclipse, Pickup, Ram-50,
Stealth & 3000GT ................ 87-101 (118-137)
Montero ............................ 72-87 (98-118)
All Others ......................... 65-80 (88-108)
\
\
\
\
\
\
WHEEL ALIGNMENT SPECIFICATIONS
WHEEL ALIGNMENT SPECIFICATIONS TABLE (COLT, COLT 200, MIRAGE, SUMMIT) \
\
\
\
\
\
\
Application Preferred Range
Camber (Degrees)
Front ....................... 0 .................... -1/2 to 1/2
Rear ..................... -11/16 .............. -13/16 to -3/16
Caster (Degrees) ........... 2 5/16 ........... 1 13/16 to 2 13/16\
Toe-In (In. (mm))
Front .................... 0 (0) ........ -1/8 to 1/8 (-3 to 3\
)
Rear ..................... 0 (0) ...... -3/16 to 3/16 (-5 to 5\
)
Toe-In (Degrees)
Front ...................... 0 .................... -1/4 to 1/4
Rear ....................... 0 .................... -3/8 to 3/8
\
\
\
\
\
\
\
WHEEL ALIGNMENT SPECIFICATIONS TABLE (COLT VISTA) \
\
\
\
\
\
\
Application Preferred Range
Two Wheel Drive
Camber (Degrees)
Front ..................... 7/16 .............. -1/16 to 15/16.
Rear ..................... -9/16 .................. -1 1/8 to 0
Caster (Degrees) .......... 13/16 ................ 5/16 to 15/16\
Toe-In (In. (mm))
Front & Rear ............. 0 (0) ........ -1/8 to 1/8 (-3 to 3\
)
Toe-In (Degrees)
Front & Rear ............... 0 .................... -1/4 to 1/4
Toe-Out on Turns (Degrees)
Inner .................... 37 3/4 ....................... .....
Outer ................... 30 11/16 ...................... .....
Four Wheel Drive