transmission MITSUBISHI MONTERO 1991 Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 302 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\](/img/19/57332/w960_57332-301.png "MITSUBISHI MONTERO 1991 Owners Manual CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\")
CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Backing plate cracked ... A ............ Require replacement.
Broken .................. A ............ Require replacement.
Contaminated with oil ... A ............ Require replacement.
Damper cushion broken ... A ............ Require replacement.
Damper cushion
collapsed .............. A ............ Require replacement.
Damper spring collapsed . A ............ Require replacement.
Damper spring missing .. C ........ ( 1) Require replacement.
Friction material cracked
through ................ B ............ Require replacement.
Friction material flaking
or chunking ............ B ............ Require replacement.
Friction material surface
cracking ............... B ......... No service suggested or
required.
Grooved ................. B ......... No service suggested or
required unless the pressure
plate or flywheel is being
resurfaced or replaced. In this
case, replacement of clutch
disc is required.
Ridged .................. B ......... No service suggested or
required unless the pressure
plate or flywheel is being
resurfaced or replaced. In this
case, replacement of clutch
disc is required.
Splines worn, affecting
performance ............ A ............ Require replacement.
Warped .................. A ............ Require replacement.
Wear exceeds
specifications (where
applicable) ............ B ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
( 1) - Not all clutch discs have springs in all spring
chambers on the disc.
\
\
\
\
\
\
\
CLUTCH FORKS
CLUTCH FORK INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A .. Require repair or replacement.
Cracked ................. B .. Require repair or replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
Page 306 of 1333
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Clamp corroded, not
reusable ............... 1 ............ Suggest replacement.
Connected incorrectly ... A ................. Require repair.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Corroded, not affecting
structural integrity ... .. ........ No service suggested or
required.
Cracked ................. A .. Require repair or replacement.
Fitting type incorrect
(such as compression
fitting) ............... B ............ Require replacement.
Flange leaking .......... A .. Require repair or replacement.
Insufficient clamping
force, allowing hose to
leak ................... A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Melted .................. 1 .. Suggest repair or replacement.
Missing ................. C ............ Require replacement.
Outer covering damaged to
the extent that the inner
fabric is visible ...... A ............ Require replacement.
Protective sleeves
damaged ................ 2 . Suggest replacement of sleeves.
Protective sleeves
missing ................ C . Require replacement of sleeves.
Restricted, affecting
performance ............ A .. Require repair or replacement.
Routed incorrectly ...... 2 ................. Require repair.
Swollen ................. 1 ............ Suggest replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Type incorrect .......... 1 .. Suggest repair or replacement.
\
\
\
\
\
\
\
COOLERS
See TRANSMISSION COOLERS .
CV JOINTS
CV JOINT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bearing, bushing or seal
surface worn, affecting
performance ............ A .. Require repair or replacement.
Boot clamp broken ....... A ... Require repair or replacement
of clamp.
Boot clamp loose ........ A ... Require repair or replacement
of clamp.
Boot clamp missing ...... C ... Require repair or replacement
of clamp.
Boot leaking ............ A . Require replacement of CV boot.
Boot surface cracked,
Page 309 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual Torn .................... A ............ Require replacement. \
\
\
\
\
\](/img/19/57332/w960_57332-308.png "MITSUBISHI MONTERO 1991 Owners Manual Torn .................... A ............ Require replacement. \
\
\
\
\
\")
Torn .................... A ............ Require replacement. \
\
\
\
\
\
\
ENGINE MOUNTS
See MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION) .
EXCITER RINGS
See TOOTHED RINGS (TONE WHEELS) .
FILLER TUBES
See DIP STICK TUBES .
FILTERS AND SCREENS
FILTER AND SCREEN INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
At service interval ..... 3 ............ Suggest replacement.
Bent .................... A .. Require repair or replacement.
Exceeding service
interval ............... 3 ............ Suggest replacement.
Missing ................. C ............ Require replacement.
Near service interval ... 3 ............ Suggest replacement.
Restricted .............. A ........... ( 1) Require repair or
replacement.
Torn .................... A ............ Require replacement.
Worn, affecting
performance (metal or
nylon screen type) ..... A .. Require repair or replacement.
( 1) - Further inspection may be required to determine the
source of restriction or contamination.
\
\
\
\
\
\
\
FLANGES
See COMPANION FLANGES .
FLEX PLATES
FLEX PLATE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, affecting
performance ............ A ............ Require replacement.
Bent, not affecting
performance ............ .. ........ No service suggested or
required.
Bolt or stud holes
elongated .............. B ............ Require replacement.
Broken .................. A ............ Require replacement.
Cracked ................. A ............ Require replacement.
Ring gear worn close
to the end of its
useful life ............ 1 ............ Suggest replacement.
Ring gear worn to the
extent that it no longer
Page 315 of 1333
Damaged, affecting
performance ............ A ............ Require replacement.
Missing ................. C ............ Require replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
LUBRICANTS
See FLUIDS AND LUBRICANTS .
METAL-CLAD SEALS
See SEALS.
METALASTIC JOINTS
See RUBBER JOINTS (METALASTIC) .
MODULATOR PINS
MODULATOR PIN INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
MODULATORS
MODULATOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, affecting
performance ............ A ............ Require replacement.
Contaminated (water, fuel,
etc.) .................. A ........ ( 1) Require replacement.
Housing cracked ......... A ............ Require replacement.
Inoperative ............. A ........ ( 2) Require replacement.
Leaking fluid
externally ............. A .. Require repair or replacement.
Leaking fluid
internally ............. A ............ Require replacement.
Leaking vacuum .......... A ............ Require replacement.
Nipple broken ........... A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Further inspection is required to determine the cause
of the contamination.
( 2) - Inoperative includes intermittent operation or out of OEM
specification.
\
\
\
\
\
\
\
MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION)
MOUNT (ENGINE, TRANSAXLE AND TRANSMISSION) INSPECTION \
\
\
\
\
\
\
Page 316 of 1333
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Broken .................. A ............ Require replacement.
Leaking (hydraulic
mount) ................. A ............ Require replacement.
Mounting hole worn,
affecting performance .. A ............ Require replacement.
Mounting hole worn, not
affecting performance .. .. ........ No service suggested or
required.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Rubber deteriorated, not
affecting performance .. .. ........ No service suggested or
required.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
ODOMETER DRIVES (MECHANICAL)
See SPEEDOMETER/ODOMETER DRIVES (MECHANICAL) .
ODOMETER HEADS (MECHANICAL)
See SPEEDOMETER/ODOMETER HEADS (MECHANICAL) .
OIL PANS
See TRANSMISSION PANS .
PANS
See TRANSMISSION PANS .
PILOT HOLES
See DOWEL PINS, GUIDES AND PILOT HOLES .
PRESSURE PLATES
PRESSURE PLATE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Balance weight missing .. C ............ Require replacement.
Broken .................. A ............ Require replacement.
Contact surface
distorted .............. B ............ Require replacement.
Cracks .................. B ............ Require replacement.
Fingers bent ............ A ............ Require replacement.
Hard spots .............. B ............ Require replacement.
Page 319 of 1333
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of
specification.
( 3) - Follow OEM recommended adjustment procedures. Repair
or replace if out of specification.
\
\
\
\
\
\
\
SIDE COVERS
See TRANSMISSION PANS .
SLIP YOKES
See YOKES AND SLIP YOKES .
SOLENOIDS
See:
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
SPEED SENSOR (ELECTRONIC WHEEL AND VEHICLE) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air gap incorrect ....... B ....... ( 1) Require adjustment or
replacement.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of hardware.
Attaching hardware
threads stripped
(threads missing) ...... A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 2) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Contaminated ............ A ........... ( 3) Require repair or
replacement.
Inoperative ............. B ........... ( 4) Require repair or
replacement. Further
inspection required.
Leaking ................. A .. Require repair or replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Resistance out of
Page 324 of 1333
incorrect .............. B ............ Require replacement.
Teeth broken ............ A ............ Require replacement.
Teeth damaged, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
TORQUE CONVERTERS
TORQUE CONVERTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Converter clutch lock-up
operation is faulty .... A ............ Require replacement.
Cover shell damaged,
affecting performance .. A ............ Require replacement.
Does not meet stall speed
specification .......... B ............ Require replacement.
End play exceeds
specifications ......... B ............ Require replacement.
Hub broken .............. A ............ Require replacement.
Hub cracked ............. A ............ Require replacement.
Internal component
failure ................ A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Pilot broken ............ A ............ Require replacement.
Pilot worn, affecting
performance ............ A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Weights missing ......... C ............ Require replacement.
\
\
\
\
\
\
\
TRANSAXLE MOUNTS
See MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION) .
TRANSDUCERS (TRANSMISSION)
See SENSORS.
TRANSMISSION COOLERS
TRANSMISSION COOLER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air flow obstruction .... A ................. Require repair.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Connection leaking ...... A .. Require repair or replacement.
Contaminated ............ A .. Require repair or replacement.
Corroded ................ 1 .. Suggest repair or replacement.
Fins damaged, affecting
Page 325 of 1333
performance ............ A .. Require repair or replacement.
Fins damaged, not
affecting performance .. .. ........ No service suggested or
required.
Internal restrictions ... B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A .. Require repair or replacement.
Tubes damaged, affecting
performance ............ A .. Require repair or replacement.
Tubes damaged, not
affecting performance .. .. ........ No service suggested or
required.
\
\
\
\
\
\
\
TRANSMISSION MOUNTS
See MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION) .
TRANSMISSION PANS
TRANSMISSION PAN INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, interfering with
filter or other internal
components ............. A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
\
\
\
\
\
\
\
TRANSMISSION RANGE INDICATORS (PRNDL)
TRANSMISSION RANGE INDICATOR (PRNDL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Binding ................. A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Components missing ...... C .. Require replacement of missing
components.
Loose, affecting
performance ............ A .. Require repair or replacement.
Out of adjustment ....... A ................. Require repair.
Worn, affecting
performance ............ A .. Require repair or replacement.
\
\
\
\
\
\
\
TUBES
See HOSES, LINES AND TUBES .
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
UNIVERSAL JOINT (CARDON OR CROSS TYPE) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Page 328 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual WHEEL SPEED SENSORS
See SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE) .
WIRING HARNESSES AND CONNECTORS
WIRING HARNESS AND CONNECTOR INSPECTION \](/img/19/57332/w960_57332-327.png "MITSUBISHI MONTERO 1991 Owners Manual WHEEL SPEED SENSORS
See SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE) .
WIRING HARNESSES AND CONNECTORS
WIRING HARNESS AND CONNECTOR INSPECTION \")
WHEEL SPEED SENSORS
See SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE) .
WIRING HARNESSES AND CONNECTORS
WIRING HARNESS AND CONNECTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B .. Require repair or replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Insulation damaged,
conductors exposed ..... A .. Require repair or replacement.
Insulation damaged,
conductors not exposed . 1 ............ Suggest replacement.
Open .................... A .. Require repair or replacement.
Protective shield
(conduit) melted ....... 2 ........... ( 1) Suggest repair or
replacement.
Protective shield
(conduit) missing ...... 2 .. Suggest repair or replacement.
Resistance (voltage drop)
out of specification ... A .. Require repair or replacement.
Routed incorrectly ...... B ................. Require repair.
Secured incorrectly ..... B ................. Require repair.
Shorted ................. A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Transmission connector
leaking ................ .. ..... See TRANSMISSION ASSEMBLY.
Voltage drop out of
specification .......... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
Page 347 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual Throttle Position Sensor (TPS) On side of throttle body.
Vehicle Speed Sensor Built into speedometer.
\
\
\](/img/19/57332/w960_57332-346.png "MITSUBISHI MONTERO 1991 Owners Manual Throttle Position Sensor (TPS) On side of throttle body.
Vehicle Speed Sensor Built into speedometer.
\
\
\")
Throttle Position Sensor (TPS) On side of throttle body.
Vehicle Speed Sensor Built into speedometer.
\
\
\
\
\
\
\
SOLENOIDS & SOLENOID VALVES \
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
Overdrive Solenoid (A/T) Left side of transmission.
Purge Control Solenoid In left front of engine
compartment.