ABS MITSUBISHI MONTERO 1991 Owner's Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 769 of 1333
4) If control arm bushing needs replacing, use press and
Bushing Remover/Installer (MB990883-01). Press bushing from control
arm. See Fig. 4.
5) Coat bushing and control arm with soapy solution. Using
press and bushing remover/installer, press bushing into control arm.
Position bushing so there is equal distance from bushing-to-control
arm at both ends.
6) Reverse bushing remover/installer to install bushing.
Position bushing so there is equal distance from bushing-to-control
arm at both ends.
CAUTION: Tighten lower control arm shaft and pivot bolt to
specification with vehicle at normal operating height.
INSTALLATION
1) To install, reverse removal procedure. Ensure White mark,
located on lower mounting end of shock absorber, faces toward outside
of vehicle. Tighten lower control arm shaft and pivot bolt to
specification with vehicle at normal operating height.
2) Tighten bolts to specification. See TORQUE SPECIFICATIONS
table at end of article. Install new nut on stabilizer bar-to-control
arm bolt. Tighten stabilizer bar-to-control arm bolt until distance
from threaded end of bolt to nut is .24-.31" (6.0-7.8 mm).
Fig. 3: Replacing Bracket Bushing
Courtesy of Mitsubishi Motor Sales of America.
Page 774 of 1333
UPPER CONTROL ARM R & I
REMOVAL
1) Remove shock absorber. Support lower control arm with jack
stand. Remove wheel assembly. Loosen anchor bolt lock nut. See Fig. 1.
2) Mark anchor bolt for reassembly reference. Loosen anchor
bolt to release torsion bar tension. Disconnect and plug brake hose at
frame mount bracket. Remove cotter pin from ball joint stud. Loosen
but DO NOT remove ball joint stud knuckle nut.
3) Using ball joint fork, loosen ball joint from steering
knuckle. Remove ball joint stud nut. Remove rebound stopper and brake
hose support from control arm. Remove upper control arm mounting
bolts. Note direction of bolt installation and location of camber
adjustment shims. Remove control arm.
4) If clearance is inadequate for control arm removal, move
control arm toward rear of vehicle and pull out front part of arm.
Rotate control arm pivot shaft and remove arm. If arm still cannot be
removed, loosen 10 front body mounting nuts. Raise body and remove
arm.
NOTE: On Montero, rotating control arm shaft will alter caster
setting.
INSPECTION
1) Inspect control arm for cracks or deformation. On Montero,
mount control arm in soft-jawed vise using control arm shaft. Attach
spring scale to upper end of control arm, near ball joint.
2) Using spring scale, measure starting torque required to
rotate control arm on the shaft. Replace control arm if starting
torque exceeds 1.4 lbs. (6.5 N).
3) On all models, check ball joints. See BALL JOINT CHECKING
under ADJUSTMENTS & INSPECTION. Inspect ball joint dust cover for
damage and replace as necessary.
INSTALLATION
1) To install, reverse removal procedure. On Montero, ensure
control arm shaft is correctly positioned before installing. Rotate
control arm shaft to obtain correct measurement. See Fig. 6.
Fig. 6: Positioning Upper Control Arm Shaft (Montero)
Courtesy of Mitsubishi Motor Sales of America.
2) On Ram-50 & Pickup, install control arm-to-crossmember
bolts from the inside of crossmember, with nuts against control arm
Page 775 of 1333
shaft.
3) On Montero, install control arm-to-crossmember bolts from
the outside of control arm, with nuts against crossmember.
4) Ensure alignment shims are placed in original location.
When installing shock absorber, ensure White paint mark on lower end
of shock faces toward the outside of vehicle. Tighten shock absorber
upper nut until distance from end of threads to nut is .27-.31" (7-8
mm). Install shock lock nut.
5) Tighten bolts to specification. See TORQUE SPECIFICATIONS
table at end of article. Bleed brakes. Adjust anchor bolt to proper
torsion bar setting. See TORSION BAR under REMOVAL & INSTALLATION.
Check wheel alignment and adjust if necessary.
WHEEL BEARINGS R & I
REMOVAL
1) Raise and support vehicle. Remove wheel assembly. Remove
caliper assembly. Remove locking hub. See LOCKING HUB under REMOVAL &
INSTALLATION.
2) Remove lock washer. Using Socket (MB990954), remove lock
nut. Remove front hub assembly from steering knuckle.
3) Remove oil seal and bearings from hub. If bearing races
need to be replaced, drive bearing races from hub using brass drift
and hammer.
INSTALLATION
1) Before installing, lubricate outside surfaces of bearing
outer races with grease. Install bearing outer races in hub. Ensure
bearing races are fully seated.
2) Pack bearings with grease. Install inner bearing in hub.
On Montero, install seal in hub using Seal Installer (MB990955). On
Pickup, use Seal Installer (MB990985).
3) Install seal until seal is even with hub surface. To
complete installation, reverse removal procedure. Adjust wheel
bearings. See WHEEL BEARINGS under ADJUSTMENTS & INSPECTION. Tighten
bolts to specification. See TORQUE SPECIFICATIONS table.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
Application Ft. Lbs. (N.m)
Anchor Bolt Lock Nut ............. 29-36 (39-49)
Automatic Hub Cover .............. 13-25 (18-34)
Ball Joint Nut
Lower ....................... 87-130 (118-176)
Upper .......................... 43-65 (58-88)
Ball Joint-to-Lower
Control Arm Bolt ............... 39-54 (53-73)
Caliper Bolt ..................... 58-72 (79-98)
Control Arm-to-Frame Bolt
Lower ................. ( 1) 101-116 (137-157)
Upper ......................... 72-87 (98-118)
Locking Hub-to-Hub/Rotor Bolt .... 36-43 (49-58)
Manual Hub Cover Bolt .................. 10 (14)
Shock Absorber Lower Mount Bolt
Montero ........................ 11-16 (15-22)
Ram-50 & Pickup ...................... 10 (14)
Page 776 of 1333
Shock Absorber Shaft Nut ......... 10-13 (14-18)
Tie Rod Nut ............................ 33 (45)
Torque Arm Bolt ................. 69-87 (94-118)
INCH Lbs. (N.m)
Stabilizer Bar Clamp Bolt ........ 84-108 (8-12)
( 1) - Tighten with vehicle at normal operating
height.
\
\
\
\
\
Page 777 of 1333
\003
* S U SPEN SIO N U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 991 M it s u bis h i M onte ro
GENERAL INFORMATION
Steering, Suspension, Wheel Alignment, Wheels and Tires
Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
Motorist Assurance Program (MAP)
OVERVIEW
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Steering and Suspension
AIR RIDE SUSPENSION
AIR RIDE SUSPENSION - AIR SHOCKS AND AIR STRUTS
AIR RIDE SUSPENSION - AIR SPRING VALVES
AIR RIDE SUSPENSION - AIR SPRINGS
AIR RIDE SUSPENSION - COMPRESSORS
AIR RIDE SUSPENSION - HEIGHT SENSORS
AIR RIDE SUSPENSION - MODULES
AIR RIDE SUSPENSION - RELAYS (COMPRESSOR)
AIR RIDE SUSPENSION - SWITCHES (ON/OFF)
AIR RIDE SUSPENSION - TORSION SPRINGS (COUNTER BALANCING)
AIR RIDE SUSPENSION - TUBING
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SUSPENSION - WIRING HARNESSES
BALL JOINTS
BUSHINGS
CENTER LINKS
CONTROL ARM SHAFTS
CONTROL ARMS
DRAG LINKS
ELECTRONIC RIDE CONTROL SHOCKS AND STRUTS
IDLER ARMS
KING PINS
PITMAN ARMS
POWER STEERING HOSES
POWER STEERING (HYDRAULIC) PUMPS
RADIUS ARMS
RELAY RODS
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
SPINDLES
SPRINGS - COIL, LEAF AND TORSION BAR
STEEL POWER STEERING LINES
STEERING ARMS
STEERING DAMPERS
STEERING GEARS (EXCEPT RACK AND PINION)
STEERING GEARS - RACK AND PINION
STEERING KNUCKLES
STRIKE OUT BUMPERS
STRUT RODS
STRUT UPPER BEARING PLATE ASSEMBLIES
SWAY BAR LINKS
SWAY BARS
Page 778 of 1333
TIE ROD ENDS (INNER AND OUTER)
TRACK BARS
TRAILING ARMS
WHEEL BEARINGS, RACES AND SEALS
Wheel Alignment
WHEEL ALIGNMENT
Wheels and Tires
TIRES
VALVE STEMS
WHEEL ATTACHMENT HARDWARE
WHEELS (RIMS)
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
1) a Pledge of Assurance to their Customers and 2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
Page 781 of 1333
the facts, allowing the customer to draw their own
conclusions and make an informed decision about how to
proceed.
STEERING AND SUSPENSION
SERVICE PROCEDURES REQUIRED AND SUGGESTED FOR PROPER VEHICLE
OPERATION
Steering and suspension are complex systems made up of a
variety of interdependent components. For proper vehicle handling,
ride, and tire wear, a thorough inspection is required whenever
suspension work is being performed.
Conditions listed assume that the problem has been isolated
to the specific component by proper testing procedures.
NOTE: When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check
and adjust alignment as needed. Refer to the OEM
specifications.
CAUTION: DO NOT use ride height altering or load compensating
components, such as variable rate springs and coil over
shocks, on vehicles with height or load sensing
proportioning valve-equipped braking systems, unless
these components are original equipment.
AIR RIDE SUSPENSION
NOTE: Depending on the air suspension design, there are some
aftermarket products available to eliminate the air ride
suspension on certain vehicles. If the system has been
eliminated with one of these products, then no service is
suggested or required.
AIR RIDE SUSPENSION - AIR SHOCKS AND AIR STRUTS
NOTE: This section covers the air spring portion of the
air shock or strut. For damping portion of shock
or strut conditions and procedures, refer to the
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
section.
AIR RIDE SUSPENSION - AIR SHOCK AND AIR STRUT INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Inner fabric of air bag
damaged ................ A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Outer covering of air bag
is cracked to the extent
that inner fabric of air
bag is visible ......... 1 ............ Suggest replacement.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - AIR SPRING VALVES
AIR RIDE SUSPENSION - AIR SPRING VALVE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Page 793 of 1333
Grease fitting missing .. C ... Require replacement of grease
fitting.
Grease fitting
won't seal ............. A ... Require replacement of grease
fitting.
Grease seal missing ..... 2 ........ (5) Suggest replacement.
Grease seal torn ........ 2 ........ ( 4) Suggest replacement.
Looseness (perceptible
horizontal movement) ... 1 ........ ( 6) Suggest replacement.
Looseness that is
excessive .............. B ..... ( 6)( 7) Require replacement.
Seized .................. A ............ Require replacement.
Stud bent ............... B ........ ( 8) Require replacement.
Stud broken ............. A ........ ( 8) Require replacement.
Stud loose in
taper hole ............. A ........... ( 8) Require repair or
replacement.
Taper hole elongated .... A ........ ( 9) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 8) Require replacement.
Wear exceeds
manufacturer's
specifications ......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - Missing grease seal will allow contaminants to enter
the joint and will accelerate wear.
( 6) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 7) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 8) - Check for damaged taper hole.
( 9) - Check for damaged stud.
\
\
\
\
\
\
\
ELECTRONIC RIDE CONTROL SHOCKS AND STRUTS
NOTE: This section covers the electronic damping control portion
of the electronic shock or strut. For dampening portion of
shock or strut conditions and procedures, refer to the
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
section.
ELECTRONIC RIDE CONTROL SHOCK AND STRUT INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Connector bent .......... A .. Require repair or replacement.
Connector broken ........ A .. Require repair or replacement.
Connector loose ......... A .. Require repair or replacement.
Electronic valve control
Page 801 of 1333
Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications .......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.
\
\
\
\
\
\
\
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
You are not required to replace shocks or struts in axle
sets. However, when replacing a shock or strut due to the conditions
that follow, you may suggest replacement of the other shock or strut
on the same axle for improved performance and preventive maintenance.
* Part is close to the end of its useful life
* To extend tire life
* To balance ride and handling
* To improve stopping distance
When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check and adjust
alignment as needed. Refer to the OEM specifications.
Under no circumstances should a technician bend struts or
strut housings.
A vehicle's load-carrying and handling abilities are limited
by its suspension, tires, brakes, and driveline. Installing coil over
shocks or any other load assist device does not increase the vehicle's
load capacity. See the vehicle owner's manual for more details.
NOTE: If vehicle is equipped with original equipment coil over
shocks, apply the conditions for coil springs from the
SPRINGS - COIL, LEAF AND TORSION BAR section of the
STEERING AND SUSPENSION guidelines. If the vehicle is
equipped with add-on coil over shocks, you may suggest
replacing the shocks with standard shocks for any spring-
related condition.
SHOCK ABSORBER, STRUT CARTRIDGE AND STRUT ASSEMBLY INSPECTION
\
\
\
\
\
\
\
Page 812 of 1333
Threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
U-joint binding ......... A ... Require repair or replacement
of joint.
U-joint loose ........... A ... Require repair or replacement
of joint.
Unequal power assist .... A .. Require repair or replacement.
(1) - Determine and correct source of contamination. Follow OE
specifications for fluid type.
( 2) - Indicates internal wear.
( 3) - If steering gear is source of inadequate assist, require
repair or replacement.
\
\
\
\
\
\
\
STEERING KNUCKLES
STEERING KNUCKLE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
bent ................... B ... Require repair or replacement
of bent part.
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Pinch bolt incorrect .... B ... Require replacement with bolt
that meets OE design.
Pinch bolt loose ........ B ................. Require repair.
Pinch bolt missing ...... B ............ Require replacement.
Pinch bolt tabs
deformed (pinched
together), .032"
or more before
clamping ............... B ........ ( 1) Require replacement.
Taper hole elongated .... A ........ ( 2) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A .. Require repair or replacement.
( 1) - Steering knuckle deformation can cause pinch
bolt breakage.
( 2) - Check for damaged stud.