diagram MITSUBISHI MONTERO 1991 Workshop Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 652 of 1333
Fig. 14: Wiring Diagram (Stealth & 3000GT 3.0L - DOHC - 1 of 2)
Page 653 of 1333
Fig. 15: Wiring Diagram (Stealth & 3000GT 3.0L - DOHC - 2 of 2)
Page 654 of 1333
Fig. 16: Wiring Diagram (Stealth & 3000GT 3.0L - Turbo - 1 of 2)
Page 655 of 1333
Fig. 17: Wiring Diagram (Stealth & 3000GT 3.0L - Turbo - 2 of 2)
Page 727 of 1333
\003
K - S EN SO R R AN G E C HAR TS
1991 M it s u bis h i M onte ro
1991 ENGINE PERFORMANCE
Sensor Operating Range Charts
Chrysler Motors: Colt, Colt 200, Colt Vista,
Ram-50, Stealth, Summit,
Mitsubishi: Eclipse, Galant, Mirage, Montero,
Pickup, 3000GT
INTRODUCTION
Sensor operating range information can help determine if a
sensor is out of calibration. An out-of-calibration sensor may not set
a trouble code, but it may cause driveability problems.
SENSOR OPERATING RANGE CHARTS
NOTE: Unless stated otherwise in test procedure, perform all
voltage tests using a Digital Volt-Ohmmeter (DVOM) with a
minimum 10-megohm input impedance. For connector and
terminal identification, see L - WIRING DIAGRAMS article in
the ENGINE PERFORMANCE Section.
COOLANT TEMP SENSOR RESISTANCE TABLE ( 1)
\
\
\
\
Temperature F (C) Ohms
Galant, Montero 3.0L, & Pickup 3.0L
32 (0) ............................. 5900
68 (20) ............................ 2500
104 (40) ........................... 2700
176 (80) ............................ 300
All Others
32 (0) ............................. 5900
68 (20) ............................ 2500
104 (40) ........................... 1100
176 (80) ............................ 300
( 1) - Measure resistance across disconnected
sensor terminals.
\
\
\
\
EGR TEMP SENSOR RESISTANCE TABLE ( 1) ( 2) \
\
\
\
Temperature F (C) Ohms
122 (50) ............................ 60-83
212 (100) .......................... 11-14
( 1) - Measure resistance across disconnected
sensor terminals.
( 2) - Specifications apply to all models
except Montero.
\
\
\
\
INTAKE AIR TEMP SENSOR RESISTANCE TABLE ( 1) \
\
\
\
Temperature F (C) Ohms
32 (0) ............................... 6000
Page 729 of 1333
![MITSUBISHI MONTERO 1991 Workshop Manual THROTTLE POSITION SENSOR (TPS) RESISTANCE TABLE \
\
\
\
\
\
Application](/img/19/57332/w960_57332-728.png "MITSUBISHI MONTERO 1991 Workshop Manual THROTTLE POSITION SENSOR (TPS) RESISTANCE TABLE \
\
\
\
\
\
Application")
THROTTLE POSITION SENSOR (TPS) RESISTANCE TABLE \
\
\
\
\
\
Application ( 1) Terminal (Ground-Output) Ohms
Colt Vista
Closed ...................... 2-1 .......... 3500-6500
Open ...................... ( 2) 2-3 ........ 3500-6500
Eclipse 2.0L (VIN R&U)
Closed ...................... 2-3 .......... 3500-6500
Open ...................... ( 2) 3-4 ........ 3500-6500
Pickup & Ram-50 3.0L
Closed ...................... 1-4 .......... 3500-6500
Open ...................... ( 2) 2-3 ........ 3500-6500
Stealth & 3000GT
Closed ...................... 4-1 .......... 3500-6500
Open ...................... ( 2) 4-2 ........ 3500-6500
All Others
Closed ...................... 1-4 .......... 3500-6500
Open ...................... ( 2) 2-4 ........ 3500-6500
( 1) - Measure across TPS terminals with connector disconnected.
( 2) - Resistance should increase smoothly.
\
\
\
\
\
\
VEHICLE SPEED SENSOR CONTINUITY TEST TABLE ( 1) \
\
\
\
\
Application ( 2) Continuity
All Models ............ 4 Changes Per Revolution
( 1) - Measure continuity at back of speedometer.
See L - WIRING DIAGRAMS article in the
ENGINE PERFORMANCE Section.
( 2) - With ECU connector disconnected. Turn speedometer
cable to cycle reed switch on and off.
\
\
\
\
\
VEHICLE SPEED SENSOR VOLTAGE TEST TABLE ( 1) \
\
\
\
\
Application ( 2) Volts
All Models
Ignition switch OFF ................ 1 Or Less
Ignition switch ON ................... 4.5-4.9
( 1) - Measure voltage at back of speedometer. See
L - WIRING DIAGRAMS article in the ENGINE
PERFORMANCE Section.
( 2) - With ECU connector disconnected. Turn speedometer
cable to cycle reed switch on and off.
\
\
\
\
\
Page 839 of 1333
\003
I - S YSTE M /C O M PO NEN T T E STS
1991 M it s u bis h i M onte ro
1991 ENGINE PERFORMANCE
System & Component Testing
Chrysler Motors: Ram-50
Mitsubishi: Montero, Pickup
INTRODUCTION
Before testing separate components or systems, perform
procedures in F - BASIC TESTING article in the ENGINE PERFORMANCE
Section. Since many computer controlled and monitored components set a
trouble code if they malfunction, also perform procedures in G - TESTS
W/CODES article in the ENGINE PERFORMANCE Section.
NOTE: Testing individual components does not isolate shorts or
opens. Perform all voltage tests with a Digital
Volt-Ohmmeter (DVOM) with a minimum 10-megohm input
impedance, unless stated otherwise in test procedure. Use
ohmmeter to isolate wiring harness shorts or opens.
COMPUTERIZED ENGINE CONTROLS
CONTROL UNIT
NOTE: To identify ECU power and ground circuits, see appropriate
L - WIRING DIAGRAMS article in the ENGINE PERFORMANCE
Section.
Ground Circuits
1) ECU is located near right kick panel. Turn ignition off.
Using an ohmmeter, check for continuity between ground and ECU
terminals No. 101 and 106. Resistance should be zero ohms. If
resistance is not zero ohms, repair open circuit between ECU connector
and ground.
2) Connect voltmeter negative lead to ground. Connect
positive lead to ECU ground terminals as in step 1). With vehicle
running, voltmeter should indicate less than one volt. If voltmeter
reading is greater than one volt, check for open, corrosion or loose
connection in ground circuit.
Power Circuits
ECU is located near right kick panel. Turn ignition on. Check
for battery voltage on ECU terminals No. 102 and 107. If battery
voltage is not present, check operation of MPI control relay. See
RELAYS under MOTORS, RELAYS & SOLENOIDS.
ENGINE SENSORS & SWITCHES
BAROMETRIC PRESSURE SENSOR
Sensor is a component part of airflow sensor assembly. See G
- TESTS W/CODES article in the ENGINE PERFORMANCE Section.
COOLANT TEMPERATURE SENSOR
1) Remove coolant temperature sensor located near thermostat
housing (2-wire connector). Place end of sensor in water with terminal\
Page 841 of 1333
mechanism. Testing information is not available from manufacturer. See
appropriate wiring diagram in L - WIRING DIAGRAMS article in the
ENGINE PERFORMANCE Section.
INTAKE AIR TEMPERATURE SENSOR
1) Sensor is incorporated in airflow sensor assembly inside
air filter housing. Disconnect airflow sensor connector. See Fig. 1.
Fig. 1: Airflow Sensor Connector Terminal ID
Courtesy of Mitsubishi Motor Sales of America.
2) Measure resistance between terminals No. 4 and 6 of
airflow sensor connector (sensor side of connector). For
specifications, see INTAKE AIR TEMPERATURE SENSOR RESISTANCE table.
Replace airflow sensor assembly if air temperature sensor resistance
is not within specification.
Page 848 of 1333
MOTORS
ISC Motor
See IDLE CONTROL SYSTEM.
RELAYS
NOTE: For internal wiring diagram of MPI control relay, see
appropriate L - WIRING DIAGRAMS article in the ENGINE
PERFORMANCE Section.
MPI Control Relay (Montero, Pickup 3.0L & Ram-50 3.0L)
1) MPI control relay is located near right kick panel. Check
for battery voltage at terminal No. 10 of relay connector. See Fig. 9.
If battery voltage is present, go to step 3). If battery voltage is
not present, check circuit between relay and battery, including
fusible link No. 1.
Fig. 9: MPI Control Relay Connector Term. ID (10 Pin)
Courtesy of Mitsubishi Motor Sales of America.
2) Apply battery voltage to terminal No. 10. Battery voltage
should not be present at terminals No. 4 and 5. Apply battery voltage
to terminal No. 10, and ground terminal No. 8. Battery voltage should
now be present at terminals No. 4 and 5.
3) Apply battery voltage to terminal No. 3. Battery voltage
should not be present at terminal No. 2. Apply battery voltage to
terminal No. 3, and ground terminal No. 7. Battery voltage should now
be present at terminal No. 2.
4) Apply battery voltage to terminal No. 9. Battery voltage
should not be present at terminal No. 2. Apply battery voltage to
terminal No. 9, and ground terminal No. 6. Battery voltage should now
be present at terminal No. 2. Replace relay if it does not test as
specified.
MPI Control Relay (Pickup 2.4L & Ram-50)
1) MPI control relay is located near right kick panel. Check
for battery voltage at terminal No. 4 of relay connector. See Fig. 10.
If battery voltage is present, go to step 3). If battery voltage is
Page 857 of 1333
SYSTE M W IR IN G D IA G RAM S
1991 M it s u bis h i M onte ro
1991 System Wiring Diagrams
Mitsubishi - Montero
COOLING FAN
Cooling Fan Circuit
DEFOGGERS