light MITSUBISHI MONTERO 1991 Workshop Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 283 of 1333
1) Install drive pinion in differential carrier. Install
spacer, pinion front shim(s) and front pinion bearing. DO NOT install
oil seal. Install pinion flange, washer and retaining nut. Tighten nut
to specification. See TORQUE SPECIFICATIONS table.
2) Check pinion rotating torque. Rotating torque must be
within specification. Correct specification is 3.5-4.3 INCH lbs. (.40-
.48 N.m) without oil seal. Adjust rotating torque by replacing drive
pinion front shims or spacer.
3) Once correct rotating torque is obtained, install oil
seal. Coat seal lip with grease. Install pinion flange so alignment
marks are correct. Apply light coat of grease to contact area of
pinion flange washer.
4) Install new retaining nut. Recheck pinion rotating torque.
Rotating torque must be within specification.
SIDE BEARING
1) Press side bearings onto differential case. Install outer
races. Install differential case into differential carrier. Align
bearing cap index marks, and snug carrier cap bolts. Ensure outer
races and bearing caps are installed in original location. Tighten
bearing cap bolts finger tight.
2) Install side bearing nuts. Tighten bearing cap bolts. See
TORQUE SPECIFICATIONS table. Rotate bearing nuts in and out until
rotation is smooth. Temporarily tighten side bearing nuts to preload
side bearings. See TORQUE SPECIFICATIONS table. Adjust ring gear
backlash.
RING GEAR BACKLASH
1) Lock drive pinion in place. Using dial indicator, check
ring gear backlash at heel of ring gear tooth. Measure at 4 locations
of ring gear. Gear backlash must be within specification. See RING
GEAR BACKLASH SPECIFICATIONS table.
RING GEAR BACKLASH SPECIFICATIONS
\
\
\
\
\
Application In. (mm)
2.4L ....................... .0043-.0063 (.109-.160)
3.0L ....................... .0051-.0071 (.130-.180)
\
\
\
\
\
2) If backlash is less than specification, loosen side
bearing nut at back of ring gear and tighten side bearing nut on tooth
side of ring gear by same amount. If backlash is beyond specification,
loosen side bearing nut at tooth side of ring gear and tighten side
bearing nut at back of ring gear by same amount.
3) After adjusting backlash, tighten both side bearing nuts
half the distance between center of 2 neighboring holes on side
bearing nut. Recheck backlash. Ensure bearing cap bolts are tightened
to specification. See TORQUE SPECIFICATIONS table.
4) Lock plates are of 2 designs for hole location of side
bearing nuts. Install proper type lock plate. Tighten lock plate bolt
to specification. See TORQUE SPECIFICATIONS table. Check gear tooth
contact using paint impression method. See GEAR TOOTH CONTACT PATTERNS
in this article.
RING GEAR RUNOUT
Using dial indicator, measure runout at back side of ring
gear. Runout must be within .002" (.05 mm). If runout is excessive,
change ring gear-to-differential case mounting position. Recheck
Page 311 of 1333
![MITSUBISHI MONTERO 1991 Workshop Manual FLYWHEEL INSPECTION \
\
\
\
\
\
\
Condition Code](/img/19/57332/w960_57332-310.png "MITSUBISHI MONTERO 1991 Workshop Manual FLYWHEEL INSPECTION \
\
\
\
\
\
\
Condition Code")
FLYWHEEL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Cracked (other than
mounting area) ......... A ...... (1) Require resurfacing or
replacement.
Cracks in mounting area . B ............ Require replacement.
Hard spots .............. B .. Require repair or replacement.
Ring gear broken ........ A ..... Require replacement of ring
gear.
Ring gear teeth worn,
affecting performance .. A ..... Require replacement of ring
gear.
Runout exceeds
specifications ......... B .. Require repair or replacement.
Scored .................. B .. Require repair or replacement.
Surface cracks after
resurfacing to
manufacturer's minimum
specifications ......... B ............ Require replacement.
Wear exceeds
specifications ......... B ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Some manufacturers allow slight surface cracking in the
friction surface.
\
\
\
\
\
\
\
FORCE MOTORS
See ACTUATORS (ELECTRICAL) .
GUIDES
See DOWEL PINS, GUIDES AND PILOT HOLES .
HALF SHAFTS
See DRIVE SHAFTS AND HALF SHAFTS .
HOSES, LINES AND TUBES
HOSE, LINE AND TUBE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Page 333 of 1333
Alternator Relay On left front of engine
compartment, behind headlight.
Condenser Fan Motor Relay On left inner fender panel.
Control Relay Behind right kick panel.
Page 335 of 1333
Hazard Flasher Relay Behind left side of dash,
above kick panel.
Headlight Control Relay On left front side of engine
compartment, behind headlight.
Page 336 of 1333
Headlight Washer Relay Behind left side of dash.
Heater Relay Behind center of dash, left of
heater box.
Intermittent Wiper Relay:
Page 339 of 1333
Seat Belt Warning Timer Behind left side of dash.
Sun Roof Control Relay In headliner, near dome light
bracket.
Turn Signal Flasher Relay Behind left side of dash. \
\
\
\
\
\
\
CIRCUIT PROTECTION DEVICES
Page 340 of 1333
![MITSUBISHI MONTERO 1991 Workshop Manual \
\
\
\
\
\
\
Component Compon](/img/19/57332/w960_57332-339.png "MITSUBISHI MONTERO 1991 Workshop Manual \
\
\
\
\
\
\
Component Compon")
\
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
A/C Dedicated Fuse Behind right side of dash, on
evaporator case.
Central Door Lock Dedicated Fuse Behind right side of dash,
left of blower assembly.
Defogger Sub-Fusible Link On wiring harness, near front
wiper motor.
Dual A/C Dedicated Fuse Behind right side of dash, on
blower case.
Headlight Dedicated Fuse On left front corner of engine
compartment.
Fuse Block On left end side of dash, near
door.
Fusible Links:
Main On right rear corner of engine
compartment, near battery.
Sub On right rear corner of engine
compartment, near battery.
Sun Roof Dedicated Fuse Behind right side of dash.
\
\
\
\
\
\
\
CONTROL UNITS \
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
Auto. Free Wheeling Hub Cntrl. Unit Behind right side of dash,
left of blower unit.
Cruise Control Unit Behind right kick panel.
Door Lock Control Unit Under center console, beside
parking brake lever.
Page 348 of 1333
![MITSUBISHI MONTERO 1991 Workshop Manual Throttle Opener Control Sol. On firewall. \
\
\
\
\
\
\](/img/19/57332/w960_57332-347.png "MITSUBISHI MONTERO 1991 Workshop Manual Throttle Opener Control Sol. On firewall. \
\
\
\
\
\
\")
Throttle Opener Control Sol. On firewall. \
\
\
\
\
\
\
SWITCHES \
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
A/C Dual Pressure Switch On right front corner of
engine compartment, near right
headlight.
A/C Thermoswitch Above evaporator.
Page 349 of 1333
A/T Thermoswitch On thermostat housing.
Brakelight Switch On bracket, above brake pedal.
Clutch Switch On bracket, above brake pedal.
Coolant Temperature Switch On front of intake manifold.
Page 352 of 1333
Self-Diagnosis Behind glove compartment.
Ignition Coil Power Transistor At rear of coil.
Maintenance Reminder Light Reset Behind instrument panel.
\
\
\
\
\
\
\