engine coolant MITSUBISHI MONTERO 1991 Manual Online
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 720 of 1333
![MITSUBISHI MONTERO 1991 Manual Online Fluid Capacities
\
\
\
\
\
\](/img/19/57332/w960_57332-719.png "MITSUBISHI MONTERO 1991 Manual Online Fluid Capacities
\
\
\
\
\
\")
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-95 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
105,000 MILE (168,000 KM) SERVICE
105,000 MILE (168,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
Page 723 of 1333
![MITSUBISHI MONTERO 1991 Manual Online Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\](/img/19/57332/w960_57332-722.png "MITSUBISHI MONTERO 1991 Manual Online Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\")
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (2.6L Engine)
\b\
\
\
\
\
\
\
Crankcase Emission Control System (PCV Valve)
\b\
\
\
\
\
\
\
Evaporative Emission Control System
\b\
\
\
\
\
\
\
Distributor Cap, Rotor & Spark Advanced System
\b\
\
\
\
\
\
\
Intake Temperature Control System
\b\
\
\
\
\
\
\
Secondary Air System
\b\
\
\
\
\
\
\
Front Disc Pads
\b\
\
\
\
\
\
\
Rear Drum Brake Linings & Wheel & Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joints
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\b\
\
\
\
\
\
\
Vacuum, Water, Crankcase Ventilation & Secondary Air Hoses
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Ignition Cables
\b\
\
\
\
\
\
\
Camshaft Timing Belt
\b\
\
\
\
\
\
\
Engine Coolant
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Vacuum Control System Solenoid Valve Air Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Page 724 of 1333
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
2.6L ........................................ 9.7 Qts. (9.2L)
3.0L ....................................... 10.0 Qts. (9.5L)
1994-95
3.5L ....................................... 10.0 Qts. (9.5L)
Differential
1987-88 ...................................... 1.9 Qts. (1.8L)
1989-94
2.6L ........................................ 1.9 Qts. (1.8L)
3.0L ........................................ 2.7 Qts. (2.6L)
1994
3.5L ........................................ 2.7 Qts. (2.6L)
1995
3.0L ........................................ 2.7 Qts. (2.6L)
3.5L ........................................ 3.3 Qts. (3.2L)
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-95 ...................................... 5.2 Qts. (4.9L)
Manual Transmission
1987-91 ...................................... 2.3 Qts. (2.2L)
1992 ......................................... 2.4 Qts. (2.3L)
1993-95 ...................................... 2.6 Qts. (2.5L)
Transfer Case
Page 725 of 1333
![MITSUBISHI MONTERO 1991 Manual Online 1987-91 ...................................... 2.3 Qts. (2.2L)
1992-95 ...................................... 2.4 Qts. (2.3L)
\
\](/img/19/57332/w960_57332-724.png "MITSUBISHI MONTERO 1991 Manual Online 1987-91 ...................................... 2.3 Qts. (2.2L)
1992-95 ...................................... 2.4 Qts. (2.3L)
\
\")
1987-91 ...................................... 2.3 Qts. (2.2L)
1992-95 ...................................... 2.4 Qts. (2.3L)
\
\
\
\
\
\
\
Service Labor Times
\
\
\
\
\
\
\
Application Hours
30,000 (60,000) 50,000
Application Mile Service Mile Service
2.6L 4-Cylinder
Automatic Transmission .... 7.9 (8.9) ................. 2.6
Manual Transmission ....... 6.9 (7.9) ................. 2.6
3.0L V6
Automatic Transmission .... 6.1 (10.6) ................ 2.6
Manual Transmission ....... 5.1 (9.6) ................. 2.6
\
\
\
\
\
\
\
\f
LUBRICATION SPECIFICATIONS TABLE\
\
\
\
\
\
\
Application Fluid Specifications
Brake & Clutch Fluid ........................... DOT 3 Or DOT 4
Engine Coolant ............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ..... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) .. SAE 10W-30 Or 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) ......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ..... SAE 85W-90, 80W-90 API GL-5
Maximum Temperature
Less Than -30
F (-34
C) ................... SAE 75W API GL-5
Power Steering Fluid ........................... Dexron-IIE ATF
Rear Axle (With Limited
Slip Differential) ........... Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic .................................... Dexron-IIE ATF
Manual Transaxle &
Transfer Case (4WD) ........... SAE 75W-85W, 75W-90 API GL-5
( 1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
FLUID CAPACITIES
FLUID CAPACITIES TABLE\
\
\
\
\
\
\
Application Quantity
A/C System R-12 Refrigerant
1983-87 .......................................... 24-26 Ozs.
1988-91 ............................................. 32 Ozs.
1992-93 ............................................. 28 Ozs.
A/C System R-134a Refrigerant ( 1)
1994-95 .......................................... 21-23 Ozs.
Automatic Transmission
Page 727 of 1333
\003
K - S EN SO R R AN G E C HAR TS
1991 M it s u bis h i M onte ro
1991 ENGINE PERFORMANCE
Sensor Operating Range Charts
Chrysler Motors: Colt, Colt 200, Colt Vista,
Ram-50, Stealth, Summit,
Mitsubishi: Eclipse, Galant, Mirage, Montero,
Pickup, 3000GT
INTRODUCTION
Sensor operating range information can help determine if a
sensor is out of calibration. An out-of-calibration sensor may not set
a trouble code, but it may cause driveability problems.
SENSOR OPERATING RANGE CHARTS
NOTE: Unless stated otherwise in test procedure, perform all
voltage tests using a Digital Volt-Ohmmeter (DVOM) with a
minimum 10-megohm input impedance. For connector and
terminal identification, see L - WIRING DIAGRAMS article in
the ENGINE PERFORMANCE Section.
COOLANT TEMP SENSOR RESISTANCE TABLE ( 1)
\
\
\
\
Temperature F (C) Ohms
Galant, Montero 3.0L, & Pickup 3.0L
32 (0) ............................. 5900
68 (20) ............................ 2500
104 (40) ........................... 2700
176 (80) ............................ 300
All Others
32 (0) ............................. 5900
68 (20) ............................ 2500
104 (40) ........................... 1100
176 (80) ............................ 300
( 1) - Measure resistance across disconnected
sensor terminals.
\
\
\
\
EGR TEMP SENSOR RESISTANCE TABLE ( 1) ( 2) \
\
\
\
Temperature F (C) Ohms
122 (50) ............................ 60-83
212 (100) .......................... 11-14
( 1) - Measure resistance across disconnected
sensor terminals.
( 2) - Specifications apply to all models
except Montero.
\
\
\
\
INTAKE AIR TEMP SENSOR RESISTANCE TABLE ( 1) \
\
\
\
Temperature F (C) Ohms
32 (0) ............................... 6000
Page 839 of 1333
\003
I - S YSTE M /C O M PO NEN T T E STS
1991 M it s u bis h i M onte ro
1991 ENGINE PERFORMANCE
System & Component Testing
Chrysler Motors: Ram-50
Mitsubishi: Montero, Pickup
INTRODUCTION
Before testing separate components or systems, perform
procedures in F - BASIC TESTING article in the ENGINE PERFORMANCE
Section. Since many computer controlled and monitored components set a
trouble code if they malfunction, also perform procedures in G - TESTS
W/CODES article in the ENGINE PERFORMANCE Section.
NOTE: Testing individual components does not isolate shorts or
opens. Perform all voltage tests with a Digital
Volt-Ohmmeter (DVOM) with a minimum 10-megohm input
impedance, unless stated otherwise in test procedure. Use
ohmmeter to isolate wiring harness shorts or opens.
COMPUTERIZED ENGINE CONTROLS
CONTROL UNIT
NOTE: To identify ECU power and ground circuits, see appropriate
L - WIRING DIAGRAMS article in the ENGINE PERFORMANCE
Section.
Ground Circuits
1) ECU is located near right kick panel. Turn ignition off.
Using an ohmmeter, check for continuity between ground and ECU
terminals No. 101 and 106. Resistance should be zero ohms. If
resistance is not zero ohms, repair open circuit between ECU connector
and ground.
2) Connect voltmeter negative lead to ground. Connect
positive lead to ECU ground terminals as in step 1). With vehicle
running, voltmeter should indicate less than one volt. If voltmeter
reading is greater than one volt, check for open, corrosion or loose
connection in ground circuit.
Power Circuits
ECU is located near right kick panel. Turn ignition on. Check
for battery voltage on ECU terminals No. 102 and 107. If battery
voltage is not present, check operation of MPI control relay. See
RELAYS under MOTORS, RELAYS & SOLENOIDS.
ENGINE SENSORS & SWITCHES
BAROMETRIC PRESSURE SENSOR
Sensor is a component part of airflow sensor assembly. See G
- TESTS W/CODES article in the ENGINE PERFORMANCE Section.
COOLANT TEMPERATURE SENSOR
1) Remove coolant temperature sensor located near thermostat
housing (2-wire connector). Place end of sensor in water with terminal\
Page 843 of 1333
specified range, replace MPS.
CAUTION: DO NOT apply more than 6 volts to ISC motor.
3) Operate ISC motor by connecting a 6-volt source directly
to appropriate terminals of ISC motor connector. For ISC motor
operation test procedures, see IDLE SPEED CONTROL (ISC) MOTOR
OPERATION TEST under IDLE CONTROL SYSTEM.
4) While operating ISC motor, measure resistance between MPS
connector terminals No. 3 and 5. Observe ohmmeter during ISC motor
operation. If MPS resistance does not vary within a 4000-6000 ohm
range or if resistance does not change smoothly, replace MPS (vehicles
equipped with separate MPS) or ISC motor assembly (vehicles equipped
with MPS incorporated in ISC).
OXYGEN SENSOR
1-Wire Or 2-Wire
1) On all models, warm engine until coolant temperature is
185-205
F (85-96C). Disconnect oxygen sensor connector. See Fig. 3 or
4.
2) Connect digital voltmeter between terminal No. 1 and
ground. Repeatedly race engine and observe oxygen sensor output
voltage. If output is not 0.6-1.0 volt, replace oxygen sensor.
Fig. 3: O2 Sensor Connector Terminal ID (1 Wire)
Courtesy of Mitsubishi Motor Sales of America.
Page 844 of 1333
Fig. 4: O2 Sensor Connector Terminal ID (2 Wire)
Courtesy of Mitsubishi Motor Sales of America.
4-Wire Heated
1) Warm engine until coolant temperature is 185-205
F (85-
Page 854 of 1333
right several times. Start engine, and turn steering wheel back and
forth to raise fluid temperature to approximately 122-140F (50-60C).
3) With engine idling, gradually close shutoff valve of
pressure gauge to increase hydraulic pressure. If idle speed does not
increase 200-250 RPM when fluid pressure reaches 213-284 psi (15-20
kg/cm
), replace power steering idle-up switch.
4) Gradually open shutoff valve. If engine speed does not
return to curb idle speed between 100-142 psi (7-10 kg/cm
), replace
power steering idle-up switch. Remove testing equipment. Bleed air
from system as in step 2).
IGNITION SYSTEM
NOTE: For basic ignition checks, see F - BASIC TESTING article in
ENGINE PERFORMANCE Section.
TIMING CONTROL SYSTEMS
Crank Angle Sensor
Crank angle sensor is located inside distributor on SOHC
engines and is attached to cylinder head on DOHC engines. If
malfunction occurs, Code 22 will set. For testing procedure, see
appropriate G - TESTS W/CODES article in the ENGINE PERFORMANCE
Section.
EMISSION SYSTEMS & SUB-SYSTEMS
EXHAUST GAS RECIRCULATION (EGR)
System Testing (Federal)
1) Disconnect Green-striped hose from throttle body, and
connect vacuum pump to hose end. Plug nipple where hose was connected
to throttle body. When engine is cold, 122
F (50C) or less, and at
idle, apply vacuum to disconnected hose. If idle does not change and
vacuum bleeds down, system is okay.
2) When engine is hot, 205
F (95C), and at idle, apply 1.8
in. Hg. If idle does not change and vacuum holds, system is okay.
Using a vacuum pump, apply 7.7 in. Hg. If idle becomes unstable or
engine stalls (and vacuum holds), system is okay.
System Testing (California)
1) Connect vacuum "T" fitting into Green-striped hose from
EGR valve, and connect vacuum gauge to vacuum tee. When engine coolant
temperature is 68
F (20C) or less and engine is idling, snap throttle
open to race engine. If no change in vacuum reading is detected on
gauge, system is okay.
2) When engine coolant temperature is 158
F (70C) or more
and engine is idling, snap throttle open to race engine. If vacuum
increases to 3.9 in. Hg or higher, system is okay.
3) Using vacuum pump, apply specified vacuum to open EGR
valve. See EGR VALVE SPECIFICATIONS table. If idle becomes unstable or
engine stalls, system is okay.
EGR Control Solenoid Valve (Pickup & Ram-50, California)
1) EGR control solenoid valve is located near left shock
tower. Label and disconnect vacuum hoses and wiring harness from
solenoid valve.
2) Connect hand vacuum pump to vacuum nipple where Green-
striped vacuum hose was connected. Apply vacuum and ensure vacuum does
not hold. Apply battery voltage to one terminal of solenoid, and
ground other. Ensure vacuum holds.
Page 855 of 1333
3) Using an ohmmeter, measure resistance between terminals of
solenoid valve. At room temperature, reading should be 36-44 ohms.
Replace solenoid if not to specification.
NOTE: EGR temperature sensor only determines if EGR is operating.
An inoperative sensor will not affect driveability or
exhaust emissions.
EGR Temperature Sensor (California)
1) Remove EGR temperature sensor from EGR valve. Place EGR
temperature sensor in water. While increasing water temperature,
measure resistance between wire terminals.
2) At a temperature of 122
F (50C), resistance should be 60,
000-80,000 ohms. At 212F (100C), resistance should be 11,000-14,000
ohms. Replace EGR temperature sensor if resistance differs
significantly from specifications.
EGR Valve
1) Remove EGR valve. Check valve for sticking, carbon
deposits and damage. Clean valve with solvent if necessary. Apply 19.8
in. Hg to valve diaphragm. If valve does not hold vacuum, replace
valve.
2) Apply specified vacuum to valve diaphragm. See CLOSED IN.
HG in EGR VALVE SPECIFICATIONS table. If valve begins to open below
specification, replace valve.
3) Apply specified vacuum to valve diaphragm. See OPEN IN. HG
in EGR VALVE SPECIFICATIONS table. If valve is not completely open at
or above specification, replace valve.
EGR VALVE SPECIFICATIONS TABLE
\
\
\
\
\
\
Application Closed Open
In. Hg In. Hg
Montero ....................... 2.4 ........... 6.7
Pickup & Ram-50 ............... 1.2 ........... 9.4
\
\
\
\
\
\
FUEL EVAPORATION
System Test
1) Disconnect Red-striped purge hose from throttle body, and
connect to hand vacuum pump. Plug nipple on throttle body where purge
hose was removed.
2) With engine coolant temperature at 140
F (60C) or less
and engine idling, apply 14.8 in. Hg. Vacuum should hold. Raise engine
speed to 3000 RPM and again apply 14.8 in. Hg. Vacuum should hold.
3) With engine coolant temperature at 158
F (70C) or more
and engine idling, apply 14.8 in. Hg. Vacuum should hold. Turn engine
off. Start engine and within 3 minutes of starting engine, apply
vacuum. Vacuum should bleed down.
4) With engine running for more than 3 minutes after
starting, raise engine speed to 3000 RPM and apply 14.8 in. Hg. Vacuum
should hold momentarily and then bleed down.
NOTE: In step 4), vacuum should bleed down continuously if vehicle
is at an altitude of 7200 ft. (2200 m) or higher or if
intake air temperature is 122
F (50C) or higher.
Purge Control Solenoid Valve
1) Purge control solenoid valve is located near left shock
tower. Label and disconnect both vacuum hoses from solenoid valve.
Disconnect electrical connector. Connect hand vacuum pump to solenoid