wiring MITSUBISHI MONTERO 1991 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 78 of 1333
Check blower switch and relay. Check A/C compressor clutch coil.
2) Ensure system is properly charged with correct amount of
refrigerant. Add refrigerant or evacuate and recharge system as
necessary. Ensure receiver-drier is not clogged. Check compressor belt
for proper tension. Check for clogged expansion valve. Check
compressor operation. Repair or replace compressor as necessary.
INSUFFICIENT AIRFLOW
Check for air leakage at air duct joint. Check for frost on
evaporator. Ensure blower motor is operating properly. Check for
obstructed air intake.
INSUFFICIENT COOLING
Ensure system is properly charged with correct amount of
refrigerant and free of air and moisture. Add refrigerant or evacuate
and recharge system as necessary. Ensure receiver-drier is not
clogged. Ensure sufficient airflow through condenser exists. Check
compressor belt for proper tension. Check compressor operation. Repair
or replace compressor as necessary. Check for clogged expansion valve.
Replace expansion valve as necessary.
INTERMITTENT COOL AIR
Check for air or moisture in system. Evacuate and recharge
system as necessary. Check for expansion valve malfunction. Replace
expansion valve if necessary. Check compressor belt for proper
tension.
TESTING
A/C SWITCH
1) Disconnect A/C switch harness connector. Using appropriate
wiring diagram as a guide, jumper appropriate terminals of A/C switch
wiring harness connector. See Fig. 4.
2) Turn blower on and momentarily turn ignition on without
starting engine. Listen for compressor clutch engagement. If
compressor clutch does not engage, check fuse and other components
wired in series with compressor clutch.
Fig. 4: A/C Switch Connector ID
Courtesy of Mitsubishi Motor Sales of America.
AIR THERMO & AIR INLET SENSORS
Page 83 of 1333
ENGINE COOLANT TEMPERATURE SWITCH
1) Turn engine off. Disconnect connector at engine coolant
temperature switch. Jumper wires on harness side of connector. If
vehicle uses a single connector, ground connector.
2) Press A/C switch to ON position and turn blower switch to
ON position. Momentarily turn ignition on and listen for compressor
clutch engagement. Clutch should engage. If clutch does not engage,
check fuse and other components wired in series with compressor
clutch.
EVAPORATOR THERMISTOR
Disconnect connector and remove thermo relay from evaporator
core. Jumper wires on harness side connector. Turn A/C switch to ON
position and turn on blower. Momentarily turn ignition on and listen
for compressor clutch engagement. If clutch does not engage, check
fuse and other components wired in series with compressor clutch.
HIGH PRESSURE SWITCH
Colt Vista
Disconnect high pressure switch connector. Jumper wires on
harness side of connector. Momentarily turn ignition on and listen for
compressor clutch engagement. If clutch does not engage, check fuse
and other components wired in series with compressor clutch.
HIGH/LOW PRESSURE CUT-OFF SWITCH
Pickup & Ram-50
1) Turn engine off. Disconnect High/Low Pressure Cut-Off
(HLPCO) switch, located on refrigerant line near condenser. Jumper
HLPCO wiring harness connector. Turn A/C switch and blower switch to
ON positions. Momentarily turn ignition on and listen for compressor
clutch engagement.
2) If compressor clutch does not engage, check evaporator
thermistor and engine coolant temperature switch. Check for a faulty
fuse. Repair or replace as necessary. If compressor clutch engages, go
to next step.
3) Connect manifold gauge set to system, and check operating
pressures. HLPCO switch should allow compressor operation if system
pressure is 28-385 psi (1.9-27 kg/cm
). If HLPCO switch does not
operate within specified pressure range, discharge system using
approved refrigerant recovery/recycling equipment, and replace switch.
4) After replacing switch, recharge system, and monitor
pressures for proper compressor function. If HLPCO switch cuts power
to compressor clutch while driving even though temperatures inside
have not yet decreased, high pressure side of new HLPCO switch has
possibly been activated. Go to next step.
5) Discharge system using approved refrigerant
recovery/recycling equipment. Replace switch, and recharge system.
Ensure compressor clutch operates within 28-385 psi (1.9-27 kg/cm
).
Check for sufficient system cooling.
LOW PRESSURE SWITCH
Colt Vista
Disconnect low pressure switch connector. Jumper wires on
harness side of connector. Momentarily turn ignition on and listen for
compressor clutch engagement. If clutch does not engage, check fuse
and other components wired in series with compressor clutch.
Page 84 of 1333
COMPRESSOR CLUTCH
Disconnect wiring to compressor clutch. Connect battery
voltage directly to A/C compressor clutch wiring harness connector
terminals. If a click is heard, clutch engagement is okay. If click is
not heard, pulley and armature are not making contact. Repair or
replace as necessary.
REAR BLOWER SWITCH
Montero
With blower switch in position indicated in REAR BLOWER
SWITCH CONTINUITY TEST table, ensure continuity exists between
terminals listed. See Fig. 8.
REAR BLOWER SWITCH CONTINUITY TEST TABLE
\
\
\
\
\
Switch Terminal
Position Numbers Continuity
OFF ................. 1-6 ................. No
Low .............. 1, 2 & 6 .............. Yes
Medium 1 ......... 1, 3 & 6 .............. Yes
Medium 2 ......... 1, 4 & 6 .............. Yes
High ............. 1, 5 & 6 .............. Yes
\
\
\
\
\
Fig. 8: Identifying Rear Blower Switch Terminals (Montero)
Courtesy of Mitsubishi Motor Sales of America.
REFRIGERANT TEMPERATURE SENSOR
Disconnect refrigerant temperature sensor electrical
connector. Using an ohmmeter, measure resistance between terminals. At
Page 87 of 1333
article, see appropriate HEATER SYSTEM article in the AIR
CONDITIONING & HEAT Section.
A/C SWITCH
Removal & Installation (Colt Vista)
From back side of control panel, push right control panel
clip right while pushing control panel out of dash panel. Allow
control panel to hang. Remove side bracket. Press temperature switch
control assembly left, and then remove A/C switch. To install, reverse
removal procedure.
Removal & Installation (Montero)
Remove lap heater duct. Remove glove box stoppers and glove
box. Remove heater control knobs. Remove center panel screw hole
plugs, and remove screws. Remove center panel. Disconnect center panel
wiring harness. Remove A/C switch. To install, reverse removal
procedure.
Removal & Installation (Pickup & Ram-50)
Remove heater control knobs. Remove glove box. Remove center
panel mounting screws. Use a trim stick to remove upper side of panel.
Remove A/C switch assembly mounting screws. Pull switch assembly
toward vehicle interior. Remove switch. To install, reverse removal
procedure.
COMPRESSOR
Removal & Installation (Colt Vista)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Disconnect high tension cable from
ignition coil. Remove distributor cap. Loosen idler pulley adjusting
bolt, and remove belt. Disconnect compressor electrical connector.
Remove high and low pressure lines and "O" rings from compressor.
Remove compressor mounting bolts. Remove compressor. To install,
reverse removal procedure.
Removal & Installation (Montero, Pickup & Ram-50)
DischargeA/C system using approved refrigerant
recovery/recycling equipment. Loosen idler pulley, and remove belt.
Disconnect compressor electrical connector. Disconnect high and low
pressure lines from compressor. Remove compressor mounting bolts.
Remove compressor. To install, reverse removal procedure.
CONDENSER
Removal & Installation (Colt Vista)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Remove front grille and grille brackets.
Remove front end cover and condenser harness. Disconnect electrical
fan connector. Slowly disconnect pressure lines from condenser. Remove
2 condenser mounting bolts. Lift up and remove condenser from vehicle.
To install, reverse removal procedure.
Removal & Installation (Montero)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Remove radiator grille. Slowly
disconnect pressure lines from condenser. Disconnect condenser fan
motor connector. Remove condenser fan mounting bolts and motor. Remove
condenser mounting bolts. Remove condenser from vehicle. To install,
reverse removal procedure.
Removal & Installation (Pickup & Ram-50)
Page 90 of 1333
Fig. 13: Exploded View of Rear Evaporator Assembly (Montero)
Courtesy of Mitsubishi Motor Sales of America.
Removal & Installation (Pickup & Ram-50)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Disconnect liquid pipe and suction hose
connections. Remove glove box assembly. Remove air and defroster
ducts. Remove evaporator drain hose and clamp. Disconnect wiring
connectors. Remove nut from firewall evaporator assembly mounting
bracket. Remove evaporator assembly. To install, reverse removal
procedure.
WIRING DIAGRAMS
Page 91 of 1333
Fig. 14: Manual A/C-Heater Wiring Diagram (Colt Vista)
Page 92 of 1333
Fig. 15: Manual A/C-Heater Wiring Diagram (Montero)
Page 93 of 1333
Fig. 16: Manual A/C-Heater Wiring Diagram (Pickup & Ram-50)
Page 95 of 1333
HEATER HOSES
HIGH PRESSURE RELIEF VALVES (HPRV)
IDLERS
IN-LINE FILTERS
METAL FITTINGS
METAL LINES
MIX AND AIR CONTROL DOORS (BLEND DOORS)
O-RINGS
ORIFICE TUBES
PILOT-OPERATED ABSOLUTES (POAS)
PLENUMS
PRESSURE CONTROL VALVES
PRESSURE SENSORS
PULLEYS
RADIATORS
RECEIVER-DRIERS
REFRIGERANT
REFRIGERANT OIL
RELAYS
SEALS
SERVICE PORTS
SPRING LOCK COUPLINGS
SUCTION THROTTLING VALVES (STVS)
SWITCHES (ELECTRICAL)
TENSIONERS
THERMISTORS AND PRESSURE SENSORS
THERMOSTATS AND HOUSINGS
VACUUM HOSES AND TUBES
VACUUM RESERVOIRS
VACUUM TUBES
VALVES IN RECEIVER (VIRS)
WATER PUMPS (ELECTRIC AUXILIARY)
WIRING HARNESSES AND CONNECTORS
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
Page 109 of 1333
required.
Fitting type incorrect
(such as compression
fitting) ............... B ............ Require replacement.
Flange leaking .......... A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Restricted internally ... A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
CONNECTORS
See WIRING HARNESSES AND CONNECTORS .
CONTROL CABLES
CONTROL CABLE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding ................. A .. Require repair or replacement.
Bracket bent, affecting
performance ............ A .. Require repair or replacement.
Bracket bent, not
affecting performance .. .. ........ No service suggested or
required.
Bracket broken, affecting
performance ............ A ............ Require replacement.
Bracket broken, not
affecting performance .. .. ........ No service suggested or
required.
Bracket corroded,
affecting performance .. A .. Require repair or replacement.
Bracket corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Bracket cracked, affecting
performance ............ A .. Require repair or replacement.
Bracket cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket holes elongated,
affecting performance .. A .. Require repair or replacement.
Bracket holes elongated,
not affecting
performance ............ .. ........ No service suggested or
required.
Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Broken .................. A .. Require repair or replacement.
Cracked ................. 2 .. Suggest repair or replacement.