oil MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 600 of 1501
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Restricted, affecting
performance ............ A .. Require repair or replacement.
\
\
\
\
\
\
\
AIR FILTER ELEMENTS
AIR FILTER ELEMENT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A ............ Require replacement.
Paper filter element
oil-soaked ............ A ........ ( 1) Require replacement.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle's OEM recommended
service intervals.
Melted .................. A ........... Required replacement.
Missing ................. C ............ Require replacement.
Restricted, affecting
performance ............ A ............ Require replacement.
Water-contaminated ...... A ........ ( 1) Require replacement.
( 1) - Further inspection required to determine cause.
\
\
\
\
\
\
\
AIR FILTER GASKETS
See AIR FILTER HOUSINGS AND GASKETS .
AIR FILTER HOUSINGS AND GASKETS
AIR FILTER HOUSING AND GASKET INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
AIR FUEL RATIO SENSORS
Page 623 of 1501
Eroded .................. 1 ............ Suggest replacement.
Loose ................... A .. Require repair or replacement.
Out of specification .... B ............ Require replacement.
\
\
\
\
\
\
\
DISTRIBUTOR SHIELDS
See DISTRIBUTOR BOOTS AND SHIELDS .
DISTRIBUTORS
DISTRIBUTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bushings worn, affecting
performance ............ A .. Require repair or replacement.
Bushings worn, not
affecting performance .. 1 .. Suggest repair or replacement.
Cam lobes worn, affecting
performance ............ A .. Require repair or replacement.
Cam lobes worn, not
affecting performance .. 1 .. Suggest repair or replacement.
Gear broken ............. A .. Require repair or replacement.
Gear worn, affecting
performance ............ A ............ Require replacement.
Gear worn, not affecting
performance ............ .. ........ No service suggested or
required.
Integrated pickup
triggering device
loose .................. A .. Require repair or replacement.
Integrated pickup
triggering device
magnetism incorrect .... A .. Require repair or replacement.
Leaking oil internally .. A .. Require repair or replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Pickup triggering device
(reluctor) broken ...... A .. Require repair or replacement.
Pickup triggering device
(reluctor) loose ....... A .. Require repair or replacement.
Pickup triggering device
(reluctor) weak ........ A .. Require repair or replacement.
Reluctor (pickup
triggering device)
broken ................. A .. Require repair or replacement.
Reluctor (pickup
triggering device)
loose .................. A .. Require repair or replacement.
Reluctor (pickup
triggering device)
weak ................... A .. Require repair or replacement.
Shaft bent .............. A ............ Require replacement.
Thrust washer broken .... A .. Require repair or replacement.
Page 629 of 1501
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine
coolant, fuel, metal particles, or water. Require
repair or replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
ENGINE COOLING SYSTEMS
NOTE: Overheating, poor engine performance, and insufficient
cabin heat can be affected by, but are not limited to,
all of the components in the engine cooling system.
ENGINE COVERS (OIL PAN, VALVE COVER, TIMING COVER)
ENGINE COVER (OIL PAN, VALVE COVER, TIMING COVER) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. B ............ Require replacement.
Attaching hardware
loose .................. A .. Require repair or replacement.
Attaching hardware
missing ................ C ............ Require replacement.
Baffle loose ............ 2 .. Suggest repair or replacement.
Baffle missing .......... C ............ Require replacement.
Bent, affecting
performance ............ A .. Require repair or replacement.
Bent, not affecting
performance ............ .. ....... No service suggested or
required.
Cracked (not leaking) ... 2 .. Suggest repair or replacement.
Leaking externally ...... A .. Require repair or replacement.
Leaking internally,
causing fluid
contamination .......... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Restricted passage ...... A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
\
\
\
\
\
\
\
ENGINE OIL
ENGINE OIL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Contaminated ............ A .. ( 1) Require replacement of oil
and filter.
Level high .............. B ... Determine source of incorrect
level and require repair.
Level low ............... B ... Determine source of incorrect
level and require repair.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle's OEM recommended
service intervals.
( 1) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water when changing oil. Require
Page 630 of 1501
![MITSUBISHI MONTERO 1998 Service Manual repair or replacement. \
\
\
\
\
\
\
ENGINE OIL CANISTER](/img/19/57333/w960_57333-629.png "MITSUBISHI MONTERO 1998 Service Manual repair or replacement. \
\
\
\
\
\
\
ENGINE OIL CANISTER")
repair or replacement. \
\
\
\
\
\
\
ENGINE OIL CANISTERS
See ENGINE OIL FILTERS AND CANISTERS .
ENGINE OIL COOLERS (EXTERNAL)
ENGINE OIL COOLER (EXTERNAL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air flow restriction .... A .. Require repair or replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bypassed ................ A .. Require repair or replacement.
Connection leaking ...... A .. Require repair or replacement.
Corroded ................ 1 .. Suggest repair or replacement.
Fins damaged, affecting
performance ............ A .. Require repair or replacement.
Fins damaged, not
affecting performance .. 2 .. Suggest repair or replacement.
Fluid flow restrictions . A .. Require repair or replacement.
Internal restrictions,
affecting performance .. A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
ENGINE OIL DRAIN PLUGS AND GASKETS
ENGINE OIL DRAIN PLUG AND GASKET INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Threads damaged ......... A ........... ( 1) Require repair or
replacement.
( 1) - Some OEMs require replacement of drain plug gasket when
removing drain plug. Inspect threads in oil pan for damage.
\
\
\
\
\
\
\
ENGINE OIL FILTERS AND CANISTERS
ENGINE OIL FILTER AND CANISTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bulged .................. A ........ ( 1) Require replacement.
Page 631 of 1501
Further inspection required.
Canister attaching
hardware broken ........ A ... Require repair or replacement
of hardware.
Canister attaching
hardware loose ......... A ................. Require repair.
Canister attaching
hardware missing ....... C ............ Require replacement.
Canister attaching
hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Center tube collapsed ... A ........ (2) Require replacement.
Further inspection required.
Contaminated ............ A ...... ( 3) Require replacement of
oil and filter.
Dented .................. 2 ........ ( 4) Suggest replacement.
Further inspection required.
Leaking ................. A .. Require repair or replacement.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle's OEM recommended
service intervals.
( 1) - Inspect pressure relief valve.
( 2) - Inspect bypass.
( 3) - Determine cause of contamination, such as engine coolant,
fuel, metal particles, or water when changing oil. Require
repair or replacement.
( 4) - Determine cause, such as broken motor mount.
\
\
\
\
\
\
\
ENGINE OIL GASKETS
See ENGINE OIL DRAIN PLUGS AND GASKETS .
ENGINE OIL PRESSURE GAUGES (MECHANICAL)
ENGINE OIL PRESSURE GAUGE (MECHANICAL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Indicates out of range .. B .......... ( 1) Further inspection
required.
Inoperative ............. A .......... ( 2) Further inspection
required.
Leaking ................. A .. Require repair or replacement.
Reads inaccurately ...... 2 .. Suggest repair or replacement.
( 1) - Gauge may indicate problem with contaminated oil, level,
pressure, or temperature, or problem with gauge.
( 2) - Gauge may indicate problem with contaminated oil, level,
pressure, or temperature, or problem with gauge.
Inoperative includes intermittent operation, out of OEM
specification, or out of range. Further inspection
required to determine cause.
\
\
\
\
\
\
\
EVAPORATIVE EMISSION (EVAP) CANISTER FILTERS
EVAPORATIVE EMISSION (EVAP) CANISTER FILTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Page 647 of 1501
affecting performance .. A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS
NOTE: When replacing fuel lines and hoses, replace with product
that meets or exceeds OEM design specifications.
HOSE AND TUBE COUPLER, CONNECTOR AND CLAMP INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Connected incorrectly ... A ................. Require repair.
Corroded, not reusable .. 1 ............ Suggest replacement.
Cracked ................. A ............ Require replacement.
Insufficient clamping
force, allowing hose to
leak ................... A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Safety clip missing (not
leaking) ............... C ... Require replacement of safety
clip.
Stripped ................ A ............ Require replacement.
\
\
\
\
\
\
\
HOSE CLAMPS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
HOSE CONNECTORS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
HOSE COUPLERS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
HOSES AND TUBES (FUEL LINES, RADIATOR, VACUUM, BY PASS,
HEATER, RECOVERY TANK AND OIL COOLERS)
HOSE AND TUBE (FUEL LINE, RADIATOR, VACUUM, BY PASS, HEATER,
RECOVERY TANK AND OIL COOLER) INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Connected incorrectly ... A ................. Require repair.
Corroded, not reusable .. 1 ............ Suggest replacement.
Cracked ................. A ............ Require replacement.
Dry-rotted .............. 1 .. Suggest repair or replacement.
Hard .................... 1 .. Suggest repair or replacement.
Inner fabric (webbing)
damaged ................ A ............ Require replacement.
Insufficient clamping
force, allowing hose to
leak ................... A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Maintenance intervals ... 3 ............ Suggest replacement.
Page 650 of 1501
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... (1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
IGNITION BOOTS
See
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY) .
IGNITION COIL TOWERS
See
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY) .
IGNITION COILS
IGNITION COIL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Arcing .................. A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
Page 651 of 1501
replacement.
Connector missing ....... C ............ Require replacement.
Corroded, affecting
performance ............ A ............ Require replacement.
Corroded, not affecting
performance ............ 2 ............ Suggest replacement.
Distorted ............... .. .... (2) No service suggested or
required.
Inoperative ............. A ........ ( 3) Require replacement.
Oil leaking ............. A ............ Require replacement.
Out of specification .... B ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Distortion may be the result of overheating; coil should
be tested.
( 3) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\
IGNITION CONTROL MODULES (ICM)
IGNITION CONTROL MODULE (ICM) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of hardware.
Attaching hardware
threads stripped
(threads missing) ...... A ... Require repair or replacement
of hardware.
Code set
(if applicable) ........ A .......... ( 1) Further inspection
required.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 2) Require repair or
replacement.
Page 652 of 1501
Connector missing ....... A ................. Require repair.
Contaminated ............ A ........... (3) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Malfunctioning .......... A ........... ( 4) Require repair or
replacement.
Missing ................. C ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 2) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Refer to manufacturer's diagnostic trouble code
procedure and require repair or replacement of affected
component(s).
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as engine
coolant, fuel, metal particles, or water. Require
repair or replacement.
( 4) - Includes inoperative, intermittent operation, or failure to
perform all functions.
\
\
\
\
\
\
\
IGNITION SWITCHES
See SWITCHES.
IGNITION TERMINALS
See
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY) .
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY)
NOTE: You are not required to replace ignition wires in sets.
However, you may suggest replacement of the entire
secondary wire set for preventive maintenance.
IGNITION WIRE, BOOT, COIL TOWER AND TERMINAL (SECONDARY) INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Page 653 of 1501
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Carbon-tracked .......... A ............ Require replacement.
Corroded ................ 1 .. Suggest repair or replacement.
Insulation leaking
(shorted) .............. A .. Require repair or replacement.
Metal heat shield bent .. 2 .. Suggest repair or replacement.
Missing ................. C ............ Require replacement.
Oil-soaked (spongy) ..... 1 ............ Suggest replacement.
Resistance incorrect .... B ............ Require replacement.
Routed incorrectly ...... 2 ............. (1) Suggest repair.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 2) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - If improper routing affects the performance of other
systems, require repair. Proper routing, hardware,
heatshields, etc., are intended to prevent premature
failure of secondary ignition components.
( 2) - Determine cause and correct prior to repair or
replacement of part.
\
\
\
\
\
\
\
IN-TANK FUEL STRAINERS
IN-TANK FUEL STRAINER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Missing ................. C ............ Require replacement.
Restricted .............. A .. Require repair or replacement.
Torn .................... A ............ Require replacement.
\
\
\
\
\
\
\
INERTIA FUEL SHUT-OFF SWITCHES
INERTIA FUEL SHUT-OFF SWITCH INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement