oil MITSUBISHI MONTERO 1998 User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 39 of 1501
A/C COMPRESSOR SERVICING
1998 Mitsubishi Montero
1998 GENERAL SERVICING
Mitsubishi - Compressor Servicing
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport &
3000GT
A/C COMPRESSOR APPLICATIONS
A/C COMPRESSOR APPLICATION TABLE \
\
\
\
\
\
Application Compressor
Diamante ......................... Sanden MSC105CVS Scroll
Eclipse
2.0L Non-Turbo ............. Nippondenso 10PA17C 10-Cyl.
2.0L Turbo & 2.4L .............. Sanden MSC105CVS Scroll
Galant ............................ Sanden MSC90C12 Scroll
Mirage ............................... Sanden MSC90 Scroll
Montero ....................... Nippondenso 10PA15 10-Cyl.
Montero Sport ...................... Sanden MSC105C Scroll
3000GT .............................. Sanden MSC105 Scroll
\
\
\
\
\
\
NOTE: Due to variety of clutch and shaft seal configurations,
obtain appropriate A/C compressor service tools for
compressor being serviced. Land Rover and Jaguar compressor
service information not available at time of publication.
NIPPONDENSO
CLUTCH COIL
Removal
1) Hold clutch plate stationary. Remove clutch plate center
bolt and clutch plate. If clutch plate cannot be removed by hand,
tighten an 8-mm or 10-mm bolt into clutch plate center bolt hole to
remove clutch plate.
2) Remove shim(s) and pulley snap ring from compressor shaft\
.
Tap pulley using a plastic hammer and remove pulley from compressor
shaft. See Fig. 1 or 2. Remove retaining screw for clutch coil lead.
Remove clutch coil snap ring and clutch coil.
Installation
1) To install, reverse removal procedure. Ensure clutch coil
pin is aligned with hole in compressor housing. Ensure clutch coil
lead is positioned properly. Ensure NEW snap rings are installed with
beveled side facing out. Tighten shaft bolt to 10-13 ft. lbs. (14-17
N.m).
2) Check air gap between clutch plate and pulley. Position
dial indicator on clutch plate. Energize clutch coil and zero dial
indicator. De-energize clutch coil and measure air gap (clutch plate
movement). Ensure air gap between clutch plate and pulley is 0.014-0.
026" (0.35-0.65 mm). If air gap is incorrect, add or remove shim(s) \
as
necessary. Ensure pulley rotates freely.
NOTE: On some compressors, it is necessary to use a dial indicator
on clutch plate to check air gap. Energize clutch coil and
zero dial indicator. De-energize clutch coil and measure air
gap. Ensure air gap is as specified.
Page 40 of 1501
SHAFT SEAL
CAUTION: Secure rear housing to compressor body using a vise before
removing front housing through-bolts. Compressor rear housing
may separate from compressor body, spilling refrigerant oil.
Removal
1) Remove clutch coil. See CLUTCH COIL. See Fig. 1 or 2.
Position compressor in a vise so compressor rear housing is secured to
compressor body. Remove front housing through-bolts and front housing.
2) Using a flat-blade screwdriver, remove felt retainer and
felt from front housing. Remove shaft seal snap ring. Using a flat-
blade screwdriver, remove shaft seal and "O" ring. See Fig. 1 or 2.
Installation
1) Inspect compressor shaft and front housing bore for damage
and/or excessive wear. Ensure "O" ring and shaft seal seat are clean.
Apply NEW refrigerant oil to compressor side of front housing bore.
Lubricate "O" ring and shaft seal with NEW refrigerant oil. Using a
21-mm socket, install shaft seal with "O" ring side facing away from
compressor. Install shaft seal snap ring. See Fig. 1 or 2.
2) Install felt into felt retainer. Using a 14-mm deep
socket, install felt and felt retainer. Lubricate compressor shaft.
Install front housing using care not damage shaft seal lip. See Fig. 1
or 2.
3) Alternately tighten front housing through-bolts to 19 ft.
lbs. (26 N.m). Install clutch plate center bolt. Using an INCH-lb.
torque wrench, ensure compressor breakaway torque is 43 INCH lbs. (4.9
N.m) or less. To complete installation, reverse removal procedures.
Ensure air gap between clutch plate and pulley is correct. See
CLUTCH COIL .
Fig. 1: Exploded View Of Compressor (Nippondenso 10PA17C 10-Cyl.)
Courtesy of Toyota Motor Sales, U.S.A., Inc.
Page 41 of 1501
Fig. 2: Exploded View Of Compressor (Typical)
Courtesy of Mitsubishi Motor Sales of America.
SANDEN SCROLL
CLUTCH COIL & SHAFT SEAL
Removal
1) Remove drive belt pulley (if equipped). Hold clutch plate\
using Pliers (MB991367) and Bolts (MB991386). Use a ratchet and sock\
et
to remove clutch hub nut.
2) Remove clutch plate. See Fig. 3 or 4. Remove snap ring
with internal snap ring pliers. Remove clutch hub (rotor). Remove snap\
ring and clutch coil.
3) Using an awl, remove bearing cover and retainer. Using
Bearing Remover (MB991456), engage bearing grooves. Place base of
bearing remover over remover arms and tighten nut.
4) Tighten bearing remover bolt to withdraw bearing from
compressor. Engage grooves of Shaft Seal Remover/Installer (MB991458)
and pull straight up on shaft seal.
Installation
1) To install shaft seal, ensure front housing is free of
foreign objects. Lubricate Shaft Seal Protector (MB991459) and place
over compressor shaft. Lubricate shaft seal and install using shaft
seal remover/installer. Remove shaft seal protector.
2) Using a 21-mm socket or Drift (MB991301), carefully press\
bearing onto compressor shaft. Install clutch coil so that alignment
pin is engaged. Install clutch coil snap ring with tapered side facing
out.
3) Align armature plate with crankshaft spline. Tighten shaft
nut to 12 ft. lbs. (16 N.m). Using feeler gauge, ensure air gap
between pressure plate and pulley is 0.02-0.03" (0.5-0.8 mm) on
Diamante and 0.016-0.024" (0.4-0.6 mm) on all other models. If air gap\
is incorrect, add or remove shim(s) as necessary.
Page 45 of 1501
HEATER HOSES
HIGH PRESSURE RELIEF VALVES (HPRV)
IDLERS
IN-LINE FILTERS
METAL FITTINGS
METAL LINES
MIX AND AIR CONTROL DOORS (BLEND DOORS)
O-RINGS
ORIFICE TUBES
PILOT-OPERATED ABSOLUTES (POAS)
PLENUMS
PRESSURE CONTROL VALVES
PRESSURE SENSORS
PULLEYS
RADIATORS
RECEIVER-DRIERS
REFRIGERANT
REFRIGERANT OIL
RELAYS
SEALS
SERVICE PORTS
SPRING LOCK COUPLINGS
SUCTION THROTTLING VALVES (STVS)
SWITCHES (ELECTRICAL)
TENSIONERS
THERMISTORS AND PRESSURE SENSORS
THERMOSTATS AND HOUSINGS
VACUUM HOSES AND TUBES
VACUUM RESERVOIRS
VACUUM TUBES
VALVES IN RECEIVER (VIRS)
WATER PUMPS (ELECTRIC AUXILIARY)
WIRING HARNESSES AND CONNECTORS
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
Page 55 of 1501
Connector missing ....... C ............ Require replacement.
Inoperative ............. A ........ (2) Require replacement.
Insulation overheated ... A ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
BLOWER SWITCHES
See SWITCHES.
CABIN AIR FILTERS
CABIN AIR FILTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air flow obstruction .... A ............. Require cleaning or
replacement.
Maintenance intervals ... 3 ............ Suggest replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
CIRCUIT BREAKERS
See FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS .
COMPRESSOR CLUTCH ASSEMBLIES
COMPRESSOR CLUTCH ASSEMBLY INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air gap incorrect ....... B .. Require repair or replacement.
Bearing seized .......... A .. Require replacement of bearing
or assembly.
Bearing worn, affecting
performance ............ A .. Require replacement of bearing
or assembly.
Coil shows signs of
overheating ............ 1 .... Suggest replacement of coil.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted,
Page 57 of 1501
Bracket broken, affecting
performance ............ A ............ Require replacement.
Bracket broken, not
affecting performance .. .. ........ No service suggested or
required.
Bracket corroded,
affecting performance .. A .. Require repair or replacement.
Bracket corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Bracket cracked, affecting
performance ............ A .. Require repair or replacement.
Bracket cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket holes elongated,
affecting performance .. A .. Require repair or replacement.
Bracket holes elongated,
not affecting
performance ............ .. ........ No service suggested or
required.
Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Housing broken, affecting
performance ............ A .. Require repair or replacement.
Housing broken, not
affecting performance .. .. ........ No service suggested or
required.
Housing cracked, affecting
performance ............ A .. Require repair or replacement.
Housing cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Inoperative ............. A ........... (1) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Noisy ................... 2 ........... ( 2) Suggest repair or
replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Tubing connection
leaking ................ A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.
( 2) - Compressor noise can also be caused by low oil level,
state of charge, air contamination, or type of
refrigerant.
\
\
\
\
\
\
\
CONDENSER AIR SEALS
CONDENSER AIR SEAL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A . Require repair or replacement.
Missing ................. C ........... Require replacement.
\
\
\
\
\
\
\
CONDENSER FAN MOTORS
Page 73 of 1501
functioning ............ A ... Require repair or replacement
of hardware.
Bearing noisy ........... 2 ............ Suggest replacement.
Bearing seized .......... A .. Require repair or replacement.
Bearing worn ............ 1 ............ Suggest replacement.
Cracked ................. A ............ Require replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Pulley damaged, affecting
belt life .............. A ............ Require replacement.
\
\
\
\
\
\
\
RADIATORS
RADIATOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air flow obstruction .... A ................. Require repair.
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Connection leaking ...... A .. Require repair or replacement.
Corroded ................ 1 .. Suggest repair or replacement.
Drain inoperative ....... A .. Require repair or replacement.
Fins damaged, affecting
performance ............ A .. Require repair or replacement.
Fins damaged, not
affecting performance .. .. ........ No service suggested or
required.
Internal oil cooler
leaking ................ A .. Require repair or replacement.
Internal restrictions ... B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A .. Require repair or replacement.
Tubes damaged, affecting
performance ............ A .. Require repair or replacement.
Tubes damaged, not
affecting performance .. .. ........ No service suggested or
required.
\
\
\
\
\
\
\
RECEIVER-DRIERS
NOTE: For VIRs, see VALVES IN RECEIVER (VIRS) .
RECEIVER-DRIER INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
Page 74 of 1501
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Contaminated, affecting
performance ............ A ............ Require replacement.
Dessicant bag
deteriorated ........... A ........ (1) Require replacement.
Further inspection required.
Dessicant at the end of
its useful life (saturated
with moisture) ......... 1 .. Suggest repair or replacement.
Fusible plug leaking .... A .... Require replacement of plug.
Leaking ................. A ............ Require replacement.
Pressure relief device
leaking ................ A . Require replacement of pressure
relief device.
Restricted .............. A .. Require repair or replacement.
Sight glass no longer
transparent ............ 2 ... Suggest replacement of drier.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Tubing connection
leaking ................ A .. Require repair or replacement.
( 1) - Inspect system to determine effects of dessicant bag
deterioration.
\
\
\
\
\
\
\
REFRIGERANT
NOTE: Refrigerants include any SNAP (Significant New Alternative
Policy)-approved blends.
REFRIGERANT INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Contaminated (other than
refrigerant blends) .... B ........ Require service to remove
contamination.
Different types of
refrigerants in the same
system (other than
refrigerant blends) .... B ................. Require repair.
Overcharged ............. B ................. Require repair.
Refrigerant type
does not match
fittings and label ..... B ................. Require repair.
Undercharged ............ B ................. Require repair.
\
\
\
\
\
\
\
REFRIGERANT OIL
REFRIGERANT OIL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Contaminated ............ 1 .. Require repair or replacement.
Overfilled .............. B ................. Require repair.
Page 79 of 1501
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Wire lead burned ........ A .. Require repair or replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
THERMOSTATS AND HOUSINGS
THERMOSTAT AND HOUSING INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
corroded ................ A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Cracked ................. A ............ Require replacement.
Housing corroded ........ 1 .......... Suggest replacement of
housing.
Inoperative ............. A ........ ( 1) Require replacement.
Installation incorrect .. B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Thermostat missing ...... C .......... Require replacement of
thermostat.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
VACUUM HOSES AND TUBES
VACUUM HOSE AND TUBE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Disconnected ............ A ................. Require repair.
Leaking ................. A .. Require repair or replacement.
Melted .................. A ..... Require repair replacement.
Missing ................. C ............ Require replacement.
Oil-soaked (spongy) ..... 1 ............ Suggest replacement.
Restricted .............. A .. Require repair or replacement.
Page 84 of 1501
A/C-HEATER SYSTEM
1998 Mitsubishi Montero
1998 AIR CONDITIONING & HEAT
Mitsubishi - A/C-Heater System
Montero
* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG RESTRAINT
SYSTEM article.
A/C SYSTEM SPECIFICATIONS
A/C SYSTEM SPECIFICATIONS TABLE \
\
\
\
\
\
Application Specification
Compressor Type ............... Nippondenso 10PA15 10-Cyl.
Compressor Belt Deflection ( 1)
New .......................... 13/64-15/64" (5.1-6.0 mm)
Used ......................... 17/64-19/64" (6.6-7.5 mm)
Compressor Oil Capacity ..................... ( 2) 2.7 ozs.
Refrigerant (R-134a) Capacity ................. 21-23 ozs.
System Operating Pressures ( 4)
High Side ............... 149-213 psi (10.5-15.0 kg/cm
)
Low Side .................... 14-33 psi (1.0-2.3 kg/cm)
( 1) - With 22 lbs. (100 N.m) force applied midway on longest
span of belt.
( 2) - Use ND 8-OIL refrigerant oil.
( 3) - Use SUN PAG 56 refrigerant oil.
( 4) - With ambient temperature at about 80
F (27C). \
\
\
\
\
\
DESCRIPTION
Slight variations exist among manual A/C-heater systems used.
On Montero, a Nippondenso 10-cylinder compressor is used. Cycling of
compressor clutch is controlled by an automatic A/C Control Unit
(ACCU).
Compressors will only operate within normal temperatures and
pressures set for each model. An electric condenser fan operates
whenever A/C system is operating. System components may vary depending
upon model. Systems may include an ACCU, fan switch, evaporator,
temperature sensor, dual-pressure switch, engine coolant temperature
switch, compressor, condenser, receiver-drier and various pipes and
hoses.
OPERATION
A/C CONTROL UNIT (ACCU)
ACCU controls cycling of compressor clutch based on
information received from air thermosensor and air inlet sensor, dual-
pressure switch, A/C switch and A/C engine coolant temperature switch.
ACCU is attached to top of evaporator housing.