battery MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 26 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
ABBREVIATION DEFINITION](/img/19/57333/w960_57333-25.png "MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
ABBREVIATION DEFINITION")
\
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
B/P Backpressure
BAC By-Pass Air Control
BAP Barometric Absolute Pressure Sensor
BARO Barometric
BBDC Before Bottom Dead Center
BCM Body Control Module
BDC Bottom Dead Center
BHP Brake Horsepower
BLK Black
BLU Blue
BMAP Barometric & Manifold Absolute Pressure Sensor
BOO Brake On-Off Switch
BP Barometric Pressure sensor
BPS Barometric Pressure Sensor
BPT Backpressure Transducer
BRN Brown
BTDC Before Top Dead Center
BTU British Thermal Unit
BVSV Bimetallic Vacuum Switching Valve
Baro. Barometric
Batt. Battery
Bbl. Barrel (Example: 4-Bbl.)
Blst. Ballast
Blwr. Blower
Brkr. Breaker
\
\
\
\
\
\
\
\f
"C" ABBREVIATION TABLE
"C" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
C Celsius (Degrees)
C(3) I Computer Controlled Coil Ignition
C(4) Computer Controlled Catalytic Converter
CANP Canister Purge solenoid
CARB California Air Resources Board
CAT Catalytic Converter
CB Circuit Breaker
CBD Closed Bowl Distributor
CBVV Carburetor Bowl Vent Valve
cc Cubic Centimeter
CCC Computer Command Control
CCD Computer Controlled Dwell
CCM Central Control Module
CCO Converter Clutch Override
CCOT Cycling Clutch Orifice Tube
CCW Counterclockwise
CDI Capacitor Discharge Ignition
CEC Computerized Engine Control
CFI Central Fuel Injection
CID Cubic Inch Displacement
CID Cylinder Identification sensor
CIS Continuous Injection System
CIS-E Continuous Injection System-Electronic
CKT Circuit
CLR Clear
CNG Compressed Natural Gas
Page 34 of 1501
TCC Torque Converter Clutch
TCCS Toyota Computer Control System
TDC Top Dead Center
TDCL Total Diagnostic Communication Link
TFI Thick Film Ignition system
TGS Top Gear Switch (cancels SIL in top gear)
THERMAC Thermostatic Air Cleaner
THS Transmission Hydraulic Switch
TP/TPS Throttle Position Sensor
TPI Tuned Port Injection
TPS Throttle Position Sensor/Switch
TS Temperature Sensor
TSB Technical Service Bulletin
TTS Transmission Temperature Switch
TV Thermovalve
TWC Three-Way Catalyst
Temp. Temperature
Trans. Transaxle/Transmission
\
\
\
\
\
\
\
\f
"V" ABBREVIATION TABLE
"V" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
V Valve
VAF Vane Air Flow sensor or circuit
VAPS Variable Assist Power Steering
VAT Vane Air Temperature
VATS Vehicle Anti-Theft System
VBATT Vehicle Battery Voltage
VCC Viscous Converter Clutch
VIN Vehicle Identification Number
VIO Violet
VLR Volt Loop Reserve
VM Vacuum Modulator
VM Vane Meter
VOM Volt-Ohmmeter (Analog)
VPWR Vehicle Power supply voltage (10-14 volts)
VREF Voltage Reference (ECA supplied reference voltage
VRV Vacuum Regulator Valve
VSC Vehicle Speed Control sensor or signal
VSS Vehicle Speed Sensor or signal
VSV Vacuum Switching Valve
Vac. Vacuum
Volt. Voltage
\
\
\
\
\
\
\
\f
"W" ABBREVIATION TABLE
"W" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
W/ With
W/O Without
WAC WOT A/C Cut-off switch or circuit
WAC Wide Open Throttle A/C Switch
WHT White
WOT Wide Open Throttle
YEL Yellow
Page 87 of 1501
settings.
2) Set blower/fan on high speed. Close doors and windows.
Insert thermometer in center vent. Operate system for 20 minutes to
allow system to stabilize. Measure temperature.
3) Discharge air temperature must be 37-44
F (3-7C) at
center vent, with high side and low side pressures within
specification. See A/C SYSTEM SPECIFICATIONS table at beginning of
article.
A/C CONTROL UNIT (ACCU)
1) Locate A/C Control Unit (ACCU) on top of evaporator case
and disconnect 10-pin connector. Inspect connector and wiring for
damage. Turn ignition and A/C on. Set temperature control to maximum
cooling and blower switch to high. Using a DVOM set to appropriate
test function, inspect harness side of connector. See Fig. 3. Go to
next step. If all test readings are as specified, replace ACCU.
2) Terminal No. 1 (Green/Yellow wire) is ACCU output. With
A/C and blower motor on, battery voltage should be present when ACCU
has received signals from pressure and temperature sensors confirming
A/C operation is okay.
3) Terminal No. 3 (Green/Blue wire) is ACCU power supply whe\
n
A/C switch is in A/C mode. With ignition and blower on, and A/C switch
at second level setting, battery voltage should be present.
4) Terminal No. 5 (Green/Red wire) is ACCU power supply when\
A/C switch is in ECONO mode. With ignition and blower on, and A/C
switch at first level setting, battery voltage should be present.
Terminals No. 2 and 7 (Black wire) are ACCU grounds. There should be
zero volts at all times.
5) Turn ignition off. Reconnect 10-pin connector. Turn
ignition on. Turn A/C on. Set temperature control to maximum cooling
and blower switch to high. Backprobe 10-pin connector. Go to next
step. If all test readings are as specified, replace ACCU.
6) Terminal No. 10 (Blue/White wire) is air thermosensor
power supply. With ignition, blower and A/C on, approximately 5.5
volts should be present.
7) Terminal No. 8 (Blue/Yellow wire) is air thermosensor
signal. When temperature of evaporator outlet portion is 77
F (25C),
there should be approximately 3.6 volts present.
8) Terminal No. 4 (White/Blue wire) is air inlet sensor powe\
r
supply. With ignition, blower and A/C on, approximately 5.5 volts
should be present.
9) Terminal No. 9 (Yellow/Green wire) is air inlet sensor
signal. When temperature of evaporator outlet portion is 77
F (25C),
there should be approximately 1.5 volts present.
Fig. 1: Testing ACCU
Courtesy of Mitsubishi Motor Sales of America.
A/C SWITCH
Page 91 of 1501
Switch Continuity Between
Position Terminal No.
OFF .................................................. (1)
Low ......................................... 1 & 8; 3 & 5
Medium-Low .................................. 1 & 8; 5 & 6
Medium-High .............................. 1, 4 & 8; 2 & 5
High ..................................... 1, 4 & 8; 5 & 7
( 1) - Continuity should not exist between any terminals.
\
\
\
\
\
\
DUAL-PRESSURE SWITCH
Disconnect dual-pressure connector, and connect a jumper wire
across harness connector terminals. Connect manifold gauge set to
system, and check operating pressures. Dual-pressure switch will allow
compressor operation when system pressure is within specification.
When high or low pressure side of dual-pressure switch is at operation
pressure (ON), condition is normal if there is continuity between the
respective terminals. If continuity is not present when switch is ON,
replace dual-pressure switch. See PRESSURE SWITCH SPECIFICATIONS
table.
PRESSURE SWITCH SPECIFICATIONS TABLE ( 1)
\
\
\
\
\
\
Application ON Pressure OFF Pressure
psi (kg/cm) psi (kg/cm)
High Pressure ......... 455 (32) .............. 541 (38)
Low Pressure .......... 32 (2.2) .............. 28 (2.0)
( 1) - With ambient temperature at 80
F (27C). \
\
\
\
\
\
COMPRESSOR CLUTCH
Disconnect wiring to compressor clutch. Connect battery
voltage directly to A/C compressor clutch wiring harness terminals. If
click is heard, clutch engagement is okay. If click is not heard,
pulley and armature are not making contact. Repair or replace as
necessary.
RELAYS
4-Terminal Relay
1) Remove relay from relay box located in engine compartment.
Using an ohmmeter, check continuity between relay terminals.
Continuity should exist between terminals No. 2 and 4, but not between
terminals No. 1 and 3. See Fig. 6.
2) Connect battery voltage to terminal No. 2, and ground
terminal No. 4. Ensure continuity now exists between terminals No. 1
and 3. If continuity is not as specified, replace relay.
Page 109 of 1501
component. Failure to do this may result in accidental air
bag deployment and possible personal injury. Refer to
DISABLING & ACTIVATING AIR BAG SYSTEM .
* For about 60 seconds after air bag system is disabled, it
retains enough voltage to deploy air bags. After disabling
system, wait at least 60 seconds before servicing.
* After servicing, always turn ignition on from passenger-side
of vehicle in case of accidental air bag deployment.
* After servicing, check SRS warning light to verify system
operation. See SYSTEM OPERATION CHECK.
* Always wear safety glasses when servicing or handling an
air bag.
* The SRS-ECU must be stored in its original special container
until used for service. It must be stored in a clean, dry
place, away from sources of extreme heat, sparks and high
electrical energy.
* DO NOT expose air bag module and clockspring to temperatures
greater than 200
F (93 C).
* When placing a live air bag module on a bench or other
surface, always face air bag module and trim cover up, away
from surface. This will reduce motion of module if air bag
accidentally deploys.
* After air bag deploys, air bag surface may contain deposits
of sodium hydroxide, which irritates skin. Always wear
safety glasses, rubber gloves and long-sleeved shirt during
clean-up. Wash hands using mild soap and water. Follow
correct clean-up and disposal procedures. Refer to
DISPOSAL PROCEDURES .
* Because of critical system operating requirements, DO NOT
service any SRS components. Repairs are only made by
replacing defective part(s).
* DO NOT allow any electrical source near inflator on the back
of air bag module.
* When carrying a live (undeployed) air bag module, trim cover
must be pointed away from body to minimize injury in case of
accidental air bag deployment.
* DO NOT probe wire harness connector terminals. Instead, use
SRS Check Harness (MB991530).
* DO NOT probe a wire through insulator, as this will damage
it and eventually cause failure due to corrosion.
* When performing electrical tests, prevent accidental
shorting of terminals. Such shorts can damage fuses or
components and may cause a second fault code to set, making
diagnosis of original problem more difficult.
* Never use an analog volt/ohm meter or test light in place of
a Digital Volt/Ohm Meter (DVOM). Use only a DVOM with a
maximum test current of 2 mA (milliamps) at minimum range of
resistance measurement. Also see SPECIAL TOOLS.
* If SRS is not fully functional for any reason, DO NOT drive
vehicle until system is repaired and is fully functional. DO
NOT remove bulbs, modules, sensors or other components, or
in any way disable system from operating normally. If SRS is
not functional, park vehicle until repairs are made.
SPECIAL TOOLS
To avoid air bag deployment when working on SRS, DO NOT use
electrical test equipment such as test lights, battery or A/C-powered
volt/ohmmeter, or any type of electrical equipment other than those
specified by manufacturer. See SRS RECOMMENDED TOOLS table.
SRS RECOMMENDED TOOLS TABLE
\
\
\
\
\
\
Page 110 of 1501
Tool Name Tool Number
For Component Replacement
Steering Wheel Puller ......................... MB990803
For Testing SRS
Digital Volt-Ohm Meter (DVOM) ...................... (1)
Multi-Use Tester II ........................... MB991502
ROM Pack ........................................... ( 2)
SRS Check Harness ............................. MB991613
For Deploying Air Bags
SRS Air Bag Adapter Harness "A" ( 3) ........... MB686560
SRS Air Bag Adapter Harness "B" ( 4) ........... MB628919
( 1) - Maximum current output of DVOM must not exceed 2 mA
(milliamps) when set on minimum range of resistance
measurement.
( 2) - ROM pack is used with multi-use tester.
( 3) - For on-vehicle deployment of driver-side air bag. For
on-vehicle or off-vehicle deployment of passenger-side
air bag.
( 4) - For off-vehicle deployment of driver-side air bag.
\
\
\
\
\
\
DISABLING & ACTIVATING AIR BAG SYSTEM
WARNING: SRS system voltage is maintained for about 60 seconds after
battery cable is disconnected. After disconnecting battery
cable, wait at least 60 seconds before servicing SRS.
Failure to wait may cause accidental air bag deployment and
possible personal injury.
To disable system, turn ignition switch to LOCK position.
Disconnect negative battery cable. Shield cable end. Wait at least 60
seconds before servicing. To activate system, reconnect negative
battery cable.
DISPOSAL PROCEDURES
WARNING: Undeployed air bag must be deployed before disposal.
Disposing of an undeployed air bag may violate federal,
state and/or local laws. This also applies to vehicles that
are to be scrapped. Never sell a used air bag module.
UNDEPLOYED AIR BAG
WARNING: Deploy air bag outdoors and away from people. Air bag
deployment makes a loud noise. NEVER deploy air bag module
with trim cover face down.
NOTE: If replacing a deployed air bag, both front impact sensors
and SRS-ECU must also be replaced. If vehicle is to be
scrapped, perform PROCEDURE 1 (ON-VEHICLE DEPLOYMENT) below.
If vehicle will continue to be operated, perform PROCEDURE 2
(OFF-VEHICLE DEPLOYMENT) below.
Procedure 1 (On-Vehicle Deployment)
1) Before proceeding, follow air bag service precautions. See
SERVICE PRECAUTIONS . Open all doors and windows. Move vehicle to an
isolated area. Disconnect negative battery cable and wrap tape around
cable terminal.
2) Disconnect positive battery cable. Remove battery. Wait at
Page 111 of 1501
![MITSUBISHI MONTERO 1998 Service Manual least 60 seconds before continuing. Remove steering column lower
cover. Disconnect clockspring 2-pin Red connector.
3) Make a harness with two 20-foot (or longer) wires. Connec\
t
wires at on](/img/19/57333/w960_57333-110.png "MITSUBISHI MONTERO 1998 Service Manual least 60 seconds before continuing. Remove steering column lower
cover. Disconnect clockspring 2-pin Red connector.
3) Make a harness with two 20-foot (or longer) wires. Connec\
t
wires at on")
least 60 seconds before continuing. Remove steering column lower
cover. Disconnect clockspring 2-pin Red connector.
3) Make a harness with two 20-foot (or longer) wires. Connec\
t
wires at one end of this harness to SRS Air Bag Adapter Harness "A"
(MB686560). Wrap connections with insulating tape. See Fig. 2.
4) Temporarily connect other end of harness wires together to
prevent unexpected air bag deployment. Connect SRS air bag adapter
harness "A" to clockspring 2-pin Red connector. Run 20-foot wires
outside of vehicle as far away as possible from vehicle.
5) Ensure there are no loose parts in passenger compartment
and no one is within 20 feet of vehicle.
6) Deploy air bag by connecting ends of 20-foot wires to
terminals of a 12-volt battery. If air bags fail to deploy, go to
PROCEDURE 2 below. After deployment, allow air bag modules to cool and
dust to settle for at least 30 minutes before approaching vehicle.
Fig. 2: Connecting Wires To Air Bag Adapter Harness
Courtesy of Mitsubishi Motor Sales of America.
Procedure 2 (Off-Vehicle Deployment)
1) Before proceeding, follow air bag service precautions. See
Page 112 of 1501
SERVICE PRECAUTIONS. Turn ignition switch to LOCK position. Disconnect
negative battery cable. Shield cable end. Disconnect positive battery
cable. Remove battery. Wait at least 60 seconds before continuing.
2) Remove air bag module. Place air bag module on ground at
least 20 feet away from people or objects. Air bag module face (trim
cover) must face upward to prevent movement of air bag module when it
is deployed.
3) Make a harness with two 20-foot (or longer) wires. Connec\
t
wires at one end of this harness to stripped wires of SRS Air Bag
Adapter Harness "B" (MB628919) for driver-side air bag, or SRS Air Bag\
Adapter Harness "A" (MB686560) for passenger-side air bag. See Fig. 2.
4) Wrap connections with insulating tape. Temporarily connect
other end of harness wires together to prevent unexpected air bag
deployment. Connect appropriate adapter harness to air bag module
connector. Place a tire without a rim over the air bag module so rim
hole surrounds air bag module. Stack 3 more tires on top of first
tire. Connect ends of 20-foot wires to terminals of a 12-volt battery.
5) After air bag module deploys, let it cool off and allow
dust to settle for at least 30 minutes before approaching. Tightly
seal deployed air bag module in a strong vinyl bag and dispose of air
bag as you would any other part.
DEPLOYED AIR BAG CLEAN-UP
WARNING: Vehicle interior will contain sodium hydroxide powder, a
by-product of air bag deployment. Since this powder can
irritate skin, eyes, nose and throat, wear safety glasses,
rubber gloves and long-sleeved shirt during clean-up.
1) Avoid breathing powder from air bag deployment. Begin
clean-up by putting tape over air bag exhaust vent to prevent
additional powder from escaping into vehicle interior. Use a vacuum
cleaner to remove any residual powder from A/C-heater outlets and
vehicle interior.
2) Turn blower motor to low for a few minutes and exit
vehicle. Turn blower motor off. Vacuum any other powder expelled from
plenum. Vacuum interior a second time to recover all powder. Avoid
kneeling or sitting on unclean areas. Wrap deployed air bag in heavy
vinyl plastic and dispose of it as you would any other part.
POST-COLLISION INSPECTION
When a vehicle has been involved in a collision, certain
components of the passive restraint system must be inspected or
replaced. See PASSIVE RESTRAINT SYSTEM INSPECTION article in the
GENERAL INFORMATION section for post-collision inspection information.
REMOVAL & INSTALLATION
WARNING: Follow air bag service precautions to prevent accidental air
bag deployment and personal injury. See SERVICE PRECAUTIONS.
Replace faulty SRS components; DO NOT repair or disassemble.
Handle all SRS components carefully.
DRIVER-SIDE AIR BAG MODULE & CLOCKSPRING
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Reactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Ensure front wheels are in straight-ahead position. Remove
lower covers from air bag module. Remove air bag module mounting nut
Page 118 of 1501
INCH Lbs. (N.m)
Air Bag Module Bolt/Nut
Driver-Side ........................................ ( 1)
Passenger-Side ..................................... ( 1)
Clockspring Screw .................................... ( 1)
SRS-ECU (Air Bag Control Unit) Bolt ............. 43 (4.9)
( 1) - Information is not available from manufacturer.
\
\
\
\
\
\
DIAGNOSIS & TESTING
INITIAL SRS DIAGNOSTIC PROCEDURE
WARNING: Follow air bag service precautions to prevent accidental air
bag deployment and personal injury. See SERVICE PRECAUTIONS.
NOTE: Ensure battery is fully charged. If battery voltage is too
low, SRS warning light will come on. When battery voltage is
restored to normal, light will go out. Codes remain stored
for no more than about 7 days. Codes can be stored no more
than 250 times. After servicing, reconnect negative battery
cable. Erase codes using Multi-Use Tester II (MUT-II,
MB991502). Check SRS warning light to verify system
operation. See SYSTEM OPERATION CHECK.
CAUTION: Ensure ignition is off before connecting or disconnecting
scan tool at DLC.
1) Before proceeding, follow service precautions. See
SERVICE PRECAUTIONS . Turn ignition on. If SRS warning light comes on
for about 7 seconds and turns off, SRS is functioning properly at this
time.
2) If SRS warning light does not come on, or comes on and
stays on, turn ignition switch to LOCK position. Connect scan tool to
Data Link Connector (DLC). See Fig. 9. Turn ignition on. Use scan tool
to retrieve code(s).
Fig. 9: Connecting Scan Tool To Data Link Connector (DLC)
Courtesy of Mitsubishi Motor Sales of America.
TROUBLE SYMPTOMS TABLE
\
\
\
\
\
\
Page 119 of 1501
Symptom Inspection Procedure
Communication With All Systems Not Possible ............ 1
Communication With SRS Only Not Possible ............... 2
Ignition Switch On (Engine Stopped)
SRS Warning Light Does Not Come On ............... DTC 43
SRS Warning Light Stays On After 7 Seconds ...... DTC 43
\
\
\
\
\
\
INSPECTION PROCEDURE 1
The cause is probably in power supply system (including
ground circuit of diagnostic line). Check connectors and harness, and
repair if necessary.
INSPECTION PROCEDURE 2
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check continuity between terminal No. 20, 21
and ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122, and repair if necessary. If
connector is okay, check for trouble symptoms. If fault exists, check
harness between SRS-ECU and ground, and repair if necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable. Measure voltage between
terminal No. 13 and 14, and body ground. If voltage at terminals is 9
volts or more, check harness wire between SRS-ECU and Data Link
Connector (DLC), and repair if necessary. If harness wire is okay,
replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION. If voltage is not as specified, check connector C-80, C-
93, C-101, and C-132, and repair if necessary. If connectors are okay,
check for trouble symptoms. If fault exists, check harness between
SRS-ECU and IG1 A or B (ignition switch), and repair if necessary.
Fig. 10: Identifying SRS Check Harness (MB991613) Connectors
Courtesy of Mitsubishi Motor Sales of America.
DTC 11, 12 & 13: FRONT IMPACT SENSOR SYSTEM