transmission oil MITSUBISHI MONTERO 1998 User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 427 of 1501
![MITSUBISHI MONTERO 1998 User Guide CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\](/img/19/57333/w960_57333-426.png "MITSUBISHI MONTERO 1998 User Guide CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\")
CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Backing plate cracked ... A ............ Require replacement.
Broken .................. A ............ Require replacement.
Contaminated with oil ... A ............ Require replacement.
Damper cushion broken ... A ............ Require replacement.
Damper cushion
collapsed .............. A ............ Require replacement.
Damper spring collapsed . A ............ Require replacement.
Damper spring missing .. C ........ ( 1) Require replacement.
Friction material cracked
through ................ B ............ Require replacement.
Friction material flaking
or chunking ............ B ............ Require replacement.
Friction material surface
cracking ............... B ......... No service suggested or
required.
Grooved ................. B ......... No service suggested or
required unless the pressure
plate or flywheel is being
resurfaced or replaced. In this
case, replacement of clutch
disc is required.
Ridged .................. B ......... No service suggested or
required unless the pressure
plate or flywheel is being
resurfaced or replaced. In this
case, replacement of clutch
disc is required.
Splines worn, affecting
performance ............ A ............ Require replacement.
Warped .................. A ............ Require replacement.
Wear exceeds
specifications (where
applicable) ............ B ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
( 1) - Not all clutch discs have springs in all spring
chambers on the disc.
\
\
\
\
\
\
\
CLUTCH FORKS
CLUTCH FORK INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A .. Require repair or replacement.
Cracked ................. B .. Require repair or replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
Page 441 of 1501
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Broken .................. A ............ Require replacement.
Leaking (hydraulic
mount) ................. A ............ Require replacement.
Mounting hole worn,
affecting performance .. A ............ Require replacement.
Mounting hole worn, not
affecting performance .. .. ........ No service suggested or
required.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Rubber deteriorated, not
affecting performance .. .. ........ No service suggested or
required.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
ODOMETER DRIVES (MECHANICAL)
See SPEEDOMETER/ODOMETER DRIVES (MECHANICAL) .
ODOMETER HEADS (MECHANICAL)
See SPEEDOMETER/ODOMETER HEADS (MECHANICAL) .
OIL PANS
See TRANSMISSION PANS .
PANS
See TRANSMISSION PANS .
PILOT HOLES
See DOWEL PINS, GUIDES AND PILOT HOLES .
PRESSURE PLATES
PRESSURE PLATE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Balance weight missing .. C ............ Require replacement.
Broken .................. A ............ Require replacement.
Contact surface
distorted .............. B ............ Require replacement.
Cracks .................. B ............ Require replacement.
Fingers bent ............ A ............ Require replacement.
Hard spots .............. B ............ Require replacement.
Page 457 of 1501
HO2S detects oxygen content in exhaust gas and sends this
information to PCM. PCM uses input signals from HO2S to vary duration
of fuel injection. HO2S heater stabilizes sensor temperature
regardless of exhaust gas temperature to allow for more accurate
exhaust oxygen content readings.
Idle Air Control (IAC) Valve Position Sensor
Sensor is incorporated in IAC motor. Sensor senses IAC motor
plunger position and sends electrical signal to PCM.
Ignition Timing Adjustment Terminal
Used for adjusting base ignition timing. When terminal is
grounded, PCM timing control function is by-passed, allowing base
timing to be adjusted.
Intake Air Temperature (IAT) Sensor
IAT sensor is incorporated into airflow sensor assembly. This
resistor-based sensor measures temperature of incoming air and
supplies air density information to PCM.
Knock Sensor (KS)
KS is located in cylinder block and senses engine vibration
during detonation (knock). KS converts vibration into electrical
signal. PCM retards ignition timing based on this signal.
Manifold Differential Pressure (MDP) Sensor
MDP sensor converts negative air pressure in intake manifold
plenum into voltage signals sent to PCM. PCM monitors Exhaust Gas
Recirculation (EGR) system using these signals.
Park/Neutral Position (PNP) Switch (Automatic Transmission)
PNP switch senses position of transmission select lever,
indicating engine load due to automatic transmission engagement. Based
on this signal, PCM commands IAC motor to increase throttle angle,
maintaining optimum idle speed.
Power Steering Oil Pressure Switch
Switch detects increase in power steering oil pressure. When
power steering oil pressure increases, switch contacts close,
signaling PCM. PCM commands IAC motor, raising idle speed to
compensate for drop in engine RPM due to power steering load.
Throttle Position (TP) Sensor
TP sensor is a variable resistor mounted on throttle body.
PCM uses voltage signal from TP sensor to determine throttle plate
angle.
Vehicle Speed Sensor (VSS)
Mounted on transaxle/transmission, VSS sends a pulsing signal
to PCM for vehicle speed calculation. PCM uses this calculation for
cruise control and fuel cut-off.
Volume Airflow (VAF) Sensor
Incorporated into airflow sensor assembly, VAF sensor
measures intake airflow rate. Intake air flows through tunnel in
airflow sensor assembly. VAF sensor sends frequency signal to PCM. PCM
uses signal to adjust fuel injection rate.
OUTPUT SIGNALS
NOTE: Vehicles are equipped with various combinations of
computer-controlled components. Not all components listed
below are used on every vehicle. To determine component
Page 589 of 1501
CLUTCH PEDAL POSITION SWITCHES
COLD START INJECTORS
CONNECTORS
COOLANT
COOLANT RECOVERY TANKS
COOLING FAN MOTOR MODULES
COOLING FAN MOTOR RELAYS AND MODULES
COOLING FAN MOTOR RESISTORS
COOLING FAN MOTOR SENSORS AND SWITCHES
COOLING FAN MOTOR SWITCHES
COOLING FAN MOTORS
CRANKSHAFT POSITION SENSORS
DECEL VALVES
DEFLECTORS
DIP STICKS AND TUBES
DIP STICK TUBES
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR BOOTS AND SHIELDS
DISTRIBUTOR CAPS
DISTRIBUTOR RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR ROTORS
DISTRIBUTOR SHIELDS
DISTRIBUTORS
EARLY FUEL EVAPORATION VALVES (HEAT RISER ASSEMBLIES)
EGR COOLERS
EGR EXHAUST MANIFOLD PASSAGES
EGR INTAKE AND EXHAUST MANIFOLD PASSAGES
EGR PLATES AND COOLERS
ELECTRONIC SPARK CONTROL MODULES
ELECTRONIC TRANSMISSION CONTROL DEVICES
ELECTRONIC TRANSMISSION FEEDBACK DEVICES
ENGINE COOLANT TEMPERATURE SENSORS
ENGINE COOLING SYSTEMS
ENGINE COVERS (OIL PAN, VALVE COVER, TIMING COVER)
ENGINE OIL
ENGINE OIL CANISTERS
ENGINE OIL COOLERS (EXTERNAL)
ENGINE OIL DRAIN PLUGS AND GASKETS
ENGINE OIL FILTERS AND CANISTERS
ENGINE OIL GASKETS
ENGINE OIL PRESSURE GAUGES (MECHANICAL)
EVAPORATIVE EMISSION (EVAP) CANISTER FILTERS
EVAPORATIVE EMISSION (EVAP) CANISTER PURGE DEVICES
EVAPORATIVE EMISSION (EVAP) CANISTERS
EVAPORATIVE EMISSION (EVAP) FEEDBACK DEVICES
EXHAUST GAS RECIRCULATION DEVICES
EXHAUST GAS RECIRCULATION FEEDBACK DEVICES
EXPANSION PLUGS
FAN CONTROL SENSORS
FUEL
FUEL ACCUMULATORS AND DAMPERS
FUEL AND COLD START INJECTORS
FUEL DAMPERS
FUEL DELIVERY CHECK VALVES
FUEL DISTRIBUTORS (BOSCH CIS)
FUEL FILLER NECKS AND RESTRICTORS
FUEL FILTERS
FUEL INJECTORS
FUEL LEVEL SENDERS7
FUEL PRESSURE REGULATORS
FUEL PUMPS (IN-TANK AND EXTERNAL, ELECTRICAL OR MECHANICAL)
FUEL RAILS
FUEL RESTRICTORS
Page 823 of 1501
INSTRUMENT PANEL
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Instrument Panels
Eclipse, Galant, Mirage, Montero, Montero Sport, 3000GT
DESCRIPTION & OPERATION
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. Do not
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
Instrument cluster includes speedometer, fuel gauge and
temperature gauge. Fuel gauge has a built-in voltage limiter to keep
voltage supply to gauges at 7 volts. Some models may also have an
ammeter, oil pressure gauge, tachometer, voltmeter and/or turbo boost
pressure gauge. Oil pressure gauge uses full battery voltage.
Tachometer operates by pulse feed.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE \
\
\
\
\
\
Component Location
Engine Coolant Temperature (ECT) Sensor
Eclipse, Galant, Montero
& Montero Sport ................. On Thermostat Housing
Mirage ........................ On Rear Of Cylinder Head
3000GT ........... On Cylinder Head, Below Ignition Coil
Input Speed Sensor
Eclipse ........................... On Side Of Transaxle
Output Speed Sensor
Eclipse ........................... On Side Of Transaxle
Vehicle Speed Sensor
Eclipse, Galant,
Mirage & 3000GT ................... On Top Of Transaxle
Montero & Montero Sport ...... On Transmission Tailshaft
\
\
\
\
\
\
TROUBLE SHOOTING
FUEL/TEMPERATURE GAUGE NOT WORKING
Check for blown fuse, faulty voltage limiter and faulty
relay. Ensure sending unit connections are clean and tight. Test
sending unit for correct operation. Tighten connections in instrument
cluster.
SPEEDOMETER NOT WORKING
On mechanical-type speedometers, ensure speedometer cable is
properly connected and correctly routed. If speedometer pointer and/or
odometer still do not work, replace speedometer cable or speedometer
assembly.
On electric-type speedometers, check for faulty vehicle speed
sensor, input/output sensors or faulty circuit. For testing, see
Page 964 of 1501
![MITSUBISHI MONTERO 1998 User Guide
\
\
\
\
\
\
\
\f
Engine Oil Ambient Temperature Less Than](/img/19/57333/w960_57333-963.png "MITSUBISHI MONTERO 1998 User Guide
\
\
\
\
\
\
\
\f
Engine Oil Ambient Temperature Less Than")
\
\
\
\
\
\
\
\f
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0\bF (-18\bC) To 100\bF (38\bC)
\
\
\
\
\
\
\f
Ambient Temperature Above 0\bF SAE 10W-30
(-18\bC) To Over 100\bF (38\bC)
\
\
\
\
\
\
\
\f
Power All Automatic Transmission
Steering Fluid DEXRON II
Fluid
\
\
\
\
\
\
\
\f
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
\f
Transfer Case All API Classification GL-4
SAE 75W-85W Or 75W-90
\
\
\
\
\
\
\
\f
Front Axle All API Classification GL-5
Or Higher (
2)
\
\
\
\
\
\
\
\f
Clutch Fluid All DOT 3 Or DOT 4
\
\
\
\
\
\
\
\f
Hook Lock All Multipurpose Grease
Catch, Door NLGI Grade 2
Lock Strikers
Seat Adjust-
ers, Backdoor
Lock, Parking
Brake Cable
Mechanism
\
\
\
\
\
\
\
\f
Front Wheel All Multipurpose Grease
Bearings NLGI Grade 2 Or
Equivalent
\
\
\
\
\
\
\
\f
Door Hinges, All Engine Oil
Back Door
Hinges
\
\
\
\
\
\
\
\f
A/C All HFC-134a
Refrigerant
\
\
\
\
\
\
\
\f
Manual All API Classification GL-4
Transmission SAE 75W-85W Or 75W-90
\
\
\
\
\
\
\
\f
Automatic All "ATF DEXRON II" Or
Transmission Equivalent
\
\
\
\
\
\
\
\f
Brake Fluid All DOT 3 Or DOT 4
\
\
\
\
\
\
\
\f
Rear Axle All API Classification GL-5
Or Higher (
2)
\
\
\
\
\
\
\
\f
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0\b F (-18\b C).
(
2) - SAE90, 85W-90, 80W-90 may be used in temperatures above
-10\b F (-23\b C). SAE 80W, 80W-90 may be used in temperatures
from -30\b F (-34\b C) to -10\b F (-23\b C). SAE 75W may be used
in temperatures below -30\b F (-34\b C).
\
\
\
\
\
\
\
Page 965 of 1501
![MITSUBISHI MONTERO 1998 User Guide FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\](/img/19/57333/w960_57333-964.png "MITSUBISHI MONTERO 1998 User Guide FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\")
FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\
Item Condition Specification
\
\
\
\
\
\
\
\f
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1)
\
\
\
\
\
\
\f
Oil Filter 0.32 Qts. (0.3L)
\
\
\
\
\
\
\f
Oil Cooler 0.32 Qts. (0.3L)
\
\
\
\
\
\
\
\f
Power Drained 1.1 Qts. (1.0L)
Steering
\
\
\
\
\
\
\
\f
Automatic Drained 8.9 Qts. (8.5L)
Transmission
\
\
\
\
\
\
\
\f
Manual Drained 3.3 Qts. (3.2L)
Transmission
\
\
\
\
\
\
\
\f
Transfer Case Drained 2.6 Qts. (2.5L)
\
\
\
\
\
\
\
\f
Front Axle Drained 1.3 Qts. (1.2L)
\
\
\
\
\
\
\
\f
Rear Axle Drained 3.3 Qts. (3.2L)
\
\
\
\
\
\
\
\f
A/C Drained 27 oz (760 g)
Refrigerant
\
\
\
\
\
\
\
\f
Fuel Tank Capacity 24 gal (92L)
\
\
\
\
\
\
\
\f
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE
\
\
\
\
\
\
Wheel Size Tire Size
15 x 6JJ (Steel or Aluminum) .................. P235/75R15
15 X 7JJ (Aluminum) ........................... P265/70R15
\
\
\
\
\
\
WHEEL TIGHTENING
Page 1046 of 1501
![MITSUBISHI MONTERO 1998 User Guide \b\
\
\
\
\
\
\
Trailer Towing Or Replace Engine Oil](/img/19/57333/w960_57333-1045.png "MITSUBISHI MONTERO 1998 User Guide \b\
\
\
\
\
\
\
Trailer Towing Or Replace Engine Oil")
\b\
\
\
\
\
\
\
Trailer Towing Or Replace Engine Oil 3,000 Mile (4800 KM)
Police, Taxi Or Or 3 Months
Commercial Type \b
\
\
\
\
\
Operation Replace Oil Filter 6,000 Mile (9600 KM)
Or 6 Months
\b
\
\
\
\
\
Replace Spark Plugs 15,000 Mile (24,000 KM)
\b
\
\
\
\
\
Replace Manual 30,000 Mile (48,000 KM)
Transmission
Oil
\b
\
\
\
\
\
Replace Transfer Oil 30,000 Mile (48,000 KM)
\b
\
\
\
\
\
\
\
Extensive Idling Replace Engine Oil 3,000 Mile (4800 KM)
Driving in Stop & Or 3 Months
Stop & Go Traffic
\b
\
\
\
\
\
Replace Oil Filter 6,000 Mile (9600 KM)
Or 6 Months
\b
\
\
\
\
\
\
\
Short-trip Replace Engine Oil 3,000 Mile (4800 KM)
Operation at Or 3 Months
Freezing \b
\
\
\
\
\
Temperatures Replace Oil Filter 6,000 Mile (9600 KM)
(Engine not Or 6 Months
thoroughly warmed)\b
\
\
\
\
\
Replace Spark Plugs 15,000 Mile (24,000 KM)
\b
\
\
\
\
\
\
\
Driving In Replace Air Cleaner 15,000 Mile (24,000 KM)
Sandy Areas Filter
\b
\
\
\
\
\
\
\
Driving In Inspect Disc Brake 6,000 Mile (9,600 KM)
Salty Areas Pads Or 6 Months
\b
\
\
\
\
\
\
\
More than 50 % Replace Engine Oil 3,000 Mile (4800 KM)
Operation in Heavy Or 3 Months
City Traffic Or \b
\
\
\
\
\
At Sustained High Replace Oil Filter 6,000 Mile (9600 KM)
Speeds During Hot Or 6 Months
Weather Above \b
\
\
\
\
\
90 F (32 C) Replace Manual 30,000 Mile (48,000 KM)
Transmission
Oil
\b
\
\
\
\
\
Replace Transfer Oil 30,000 Mile (48,000 KM)
\b
\
\
\
\
\
\
\
Driving On Replace Manual 30,000 Mile (48,000 KM)
Off-Road Transmission
Oil
\b
\
\
\
\
\
Replace Transfer Oil 30,000 Mile (48,000 KM)
\b
\
\
\
\
\
\
\
(
1) - Perform these services at the mileage or number of months
(since the last time), WHICHEVER COMES FIRST.
\f
\
\
\
\
\
\
\
7,500 MILE (12,000 KM) NORMAL SERVICE
7,500 MILE (12,000 KM) NORMAL SERVICE
Page 1049 of 1501
![MITSUBISHI MONTERO 1998 User Guide \b\
\
\
\
\
\
\
Engine Oil Oil Pan](/img/19/57333/w960_57333-1048.png "MITSUBISHI MONTERO 1998 User Guide \b\
\
\
\
\
\
\
Engine Oil Oil Pan")
\b\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
30,000 MILE (48,000 KM) NORMAL SERVICE
30,000 MILE (48,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
SERVICE
\b
\
\
\
\
\
\
\
Ball Joints With Grease Nipple (
6)
\b
\
\
\
\
\
\
\
Propeller Shaft Joints (
6)
\b
\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Fuel Hoses (
3)
\b
\
\
\
\
\
\
\
Drive Belt (For Generator, Water Pump, Power Steering Pump)
\b
\
\
\
\
\
\
\
Manual Transmission Oil
\b
\
\
\
\
\
\
\
Transfer Oil
\b
\
\
\
\
\
\
\
Disc Brake Pads (
4)
\b
\
\
\
\
\
\
\
Brake Hoses (
4)
\b
\
\
\
\
\
\
\
Ball Joint & Steering Linkage Seals (
3)
\b
\
\
\
\
\
\
\
Drive Shaft Boots (
4)
\b
\
\
\
\
\
\
\
Exhaust System (
3)
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
Engine Coolant
\b
\
\
\
\
\
\
\
Automatic Transmission Fluid
\b
\
\
\
\
\
\
\
Rear Axle Oil
\b
\
\
\
\
\
\
\
Air Cleaner Filter
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
Page 1050 of 1501
(3) - Or inspect every 2 years.
(
4) - Or inspect every year.
(
5) - Or change every 2 years.
(
6) - Or lubricate grease every 2 years.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\b
\
\
\
\
\
\
\
Manual All API Classification GL-4
Transmission SAE 75W-85W Or 75W-90
\b
\
\
\
\
\
\
\
Automatic All "ATF DEXRON II" Or
Transmission Equivalent
\b
\
\
\
\
\
\
\
Brake Fluid All DOT 3 Or DOT 4
\b
\
\
\
\
\
\
\
Rear Axle All API Classification GL-5
Or Higher (
2)
\b
\
\
\
\
\
\
\
Transfer Case All API Classification GL-4
SAE 75W-85W Or 75W-90
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
(
2) - SAE90, 85W-90, 80W-90 may be used in temperatures above
-10 F (-23 C). SAE 80W, 80W-90 may be used in temperatures
from -30 F (-34 C) to -10 F (-23 C). SAE 75W may be used
in temperatures below -30 F (-34 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
Engine Drained; With Reserve Tank 10 Qts. (9.5L)
Coolant
\b
\
\
\
\
\
\
\
Automatic Drained 8.9 Qts. (8.5L)
Transmission
\b
\
\
\
\
\
\
\
Manual Drained 3.3 Qts. (3.2L)
Transmission
\b
\
\
\
\
\
\
\
Rear Axle Drained 3.3 Qts. (3.2L)
\b
\
\
\
\
\
\
\
Transfer Case Drained 2.6 Qts. (2.5L)