bolts MITSUBISHI MONTERO 1998 Repair Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 997 of 1501
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Drain coolant. Remove air intake
hose. Remove throttle body and gasket with control cables and vacuum
hoses attached.
2) Remove EGR pipe (if equipped). Disconnect power brake
hose. Label and disconnect vacuum hoses and wiring harness connectors
as necessary. Remove intake plenum brackets and mounting bolts. Remove
intake plenum and gasket.
3) Disconnect high pressure fuel hose at fuel rail.
Disconnect fuel return hose. Disconnect vacuum hoses. Disconnect
injector electrical connectors. Remove fuel rail bolts, and lift fuel
rail and injectors from engine. Injectors may be removed after fuel
rail is removed from intake manifold.
Installation
To install, reverse removal procedure. Use NEW insulators and
"O" rings when installing injectors. Install injectors into fuel rail
with a twisting motion. Ensure injectors rotate smoothly when
installing. Refill cooling system.
Removal (Eclipse, Galant, Mirage & Montero Sport 3.0L)
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Disconnect PCV hose and breather
hoses. Disconnect high pressure fuel hose at fuel rail. Disconnect
fuel return hose and vacuum hoses.
2) Disconnect injector electrical connectors. Remove fuel
rail bolts, and lift fuel rail and injectors from engine. Injectors
may be removed after fuel rail is removed from intake manifold.
Installation
To install, reverse removal procedure. Use NEW insulators and
"O" rings when installing injectors. Use lubricant on "O" rings.
Install injectors into fuel rail with a twisting motion. Ensure
injectors rotate smoothly when installing.
Removal (Montero)
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Remove air intake hose. Remove
accelerator cable adjusting bolts. On A/T models, remove throttle
control cable. On all models, remove accelerator cable. Label and
disconnect all vacuum hoses from throttle body and upper intake
manifold (air intake plenum).
2) Remove EGR pipe and gasket. Remove ignition coil (if
necessary). Remove engine oil filler neck bracket. Disconnect PCV
hose. Remove throttle body, leaving coolant hoses connected. Remove
throttle body gasket. Remove front and rear intake plenum brackets.
Remove intake plenum mounting bolts. Remove intake plenum and gasket.
3) Disconnect high pressure fuel hose at fuel rail.
Disconnect fuel return hose. Disconnect vacuum hoses. Disconnect
injector electrical connectors. Remove fuel rail bolts, and lift fuel
rail and injectors from engine. Injectors may be removed after fuel
rail is removed from intake manifold.
Installation
To install, reverse removal procedure. Use NEW insulators and
"O" rings when installing injectors. Use lubricant on "O" rings.
Install injectors into fuel rail using a twisting motion. Ensure
injectors rotate smoothly when installing. Adjust throttle control and
accelerator cables (if necessary). Refill cooling system.
HEATED OXYGEN SENSOR (HO2S)
Removal & Installation
Page 998 of 1501
1) Front HO2S is mounted in exhaust pipe below exhaust
header. Rear HO2S is mounted behind catalytic converter. HO2S is
equipped with a permanent pigtail which must be protected from damage
when HO2S is removed. Ensure HO2S is free of contaminants. Avoid using
cleaning solvents of any type.
2) HO2S may be difficult to remove when engine temperature is
less than 120
F (48 C). If using original sensor, always use anti-
seize compound on threads before installation. New sensor threads are
precoated with anti-seize. Tighten HO2S to specification. See
TORQUE SPECIFICATIONS .
THROTTLE BODY
Removal
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Drain enough coolant to ensure coolant level is below throttle body.
Disconnect air intake hose.
2) Remove accelerator, cruise control and A/T throttle valve
cables (if equipped). Disconnect fuel vapor hose, electrical harness
connector, vacuum hose and coolant hoses. Remove throttle body
retaining bolts.
Disassembly
Remove throttle position sensor. Remove idle air control
motor. Remove throttle bracket and connector bracket (if equipped).
Remove idle position switch and adjusting nut (if equipped).
CAUTION: DO NOT remove throttle valve. DO NOT use cleaning solvents
on throttle position sensor, idle air control motor or idle
position switch.
Cleaning
1) Clean all parts except throttle position sensor, idle air
control motor and idle position switch in solvent.
WARNING: Safety glasses MUST be worn whenever compressed air is used
for parts cleaning.
2) Check vacuum port and passage for clogging. Clean vacuum,
vapor and fuel passages using compressed air.
Reassembly
To reassemble, reverse disassembly procedure.
Installation
To install, reverse removal procedure.
THROTTLE POSITION (TP) SENSOR
Removal & Installation
Throttle Position (TP) sensor is located on throttle body.
Disconnect TP sensor electrical connector. Remove TP sensor screws and
TP sensor. To install, reverse removal procedure. Tighten TP sensor
screws to specification. See TORQUE SPECIFICATIONS. For TP sensor
adjustment procedure, see D - ADJUSTMENTS article.
TURBOCHARGERS
Removal (Eclipse)
1) Disconnect negative battery cable. Drain engine coolant
and oil. On models equipped with A/C, remove condenser fan motor
assembly. Remove front heated oxygen sensor. Remove oil dipstick guide
and "O" ring.
Page 999 of 1501
2) Disconnect air intake hose and vacuum hoses. Remove air
hose and air outlet housing. Remove heat protectors. Disconnect
exhaust pipe. Remove power steering oil pump and bracket. Remove
engine hanger bracket. Disconnect oil inlet pipe.
3) Disconnect engine coolant hoses and tubes from
turbocharger. Remove exhaust manifold nuts and bolts. Remove exhaust
manifold and gaskets. Disconnect oil pressure and return pipes. Remove
turbocharger and exhaust manifold assembly. Separate turbocharger from
exhaust manifold.
Removal (3000GT - Front)
1) Disconnect negative battery cable. Drain engine oil and
coolant. Remove radiator. Disconnect exhaust pipe. Remove air intake
hose, air hoses and air pipe. Remove generator and belt. Remove oil
dipstick guide.
2) Remove heat protector. Disconnect front heated oxygen
sensor connector. Remove oil return pipe. Remove turbocharger support
bracket, and remove turbocharger from exhaust manifold.
Removal (3000GT - Rear)
1) Disconnect battery cables, and remove battery. Drain
engine oil and cooling system. Remove accelerator cable. Remove air
hose, air pipe and heat protectors. Disconnect clutch booster vacuum
hose. Remove air intake hoses and EGR pipe. Disconnect heated oxygen
sensor connectors.
2) Remove oil pipe and EGR valve. Disconnect exhaust fitting,
and remove rear heat protector. Remove oil return pipe. Remove
turbocharger assembly.
Inspection (All Models)
Check turbine and compressor wheels for cracking and other
damage. Ensure turbine and compressor wheels turn smoothly. Check for
oil leakage from turbocharger assembly. Check for proper wastegate
valve operation. See I - SYSTEM/COMPONENT TESTS article.
CAUTION: Apply light coat of oil to inner surface of flared area on
water pipe (flare nut fitting) before connecting to engine.
Installation (All Models)
1) To install, reverse removal procedure. Before oil pipe
flare nut (above turbocharger) is installed, pour clean engine oil
into turbocharger oil pipe installation hole. Ensure oil and air hoses
are properly installed and securely clamped.
2) Use NEW gaskets. Adjust accelerator cable (if necessary).\
Refill engine oil and coolant. Check for oil and coolant leaks.
Tighten all bolts to specification. See TORQUE SPECIFICATIONS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Applications Ft. Lbs. (N.m)
Coolant Pipe-To-Turbocharger Banjo Bolt .......... 31 (42)
EGR Valve ........................................ 16 (22)
Engine Coolant Temperature Sensor ................ 22 (30)
Exhaust Manifold-To-Engine Nuts ............ 18-21 (24-29)
Exhaust Manifold-To-Turbocharger Bolts ..... 40-47 (54-64)
Exhaust Pipe Bolts ......................... 21-36 (29-49)
Fuel Filter Line ................................. 27 (36)
Fuel Tank Drain Plug ....................... 11-18 (15-24)
Fuel Tank Nuts ............................. 15-21 (20-29)
Page 1000 of 1501
Heated Oxygen Sensor
Front .................................... 29-33 (39-44)
Rear ..................................... 15-29 (20-39)
Heat Protector Bolts .................. 8.8-11 (12.0-15.0)
Intake Manifold Plenum Bolt/Nut .................. 13 (18)
Knock Sensor ............................... 15-18 (20-24)
Oil Return Pipe-To-Engine .................. 10-14 (14-19)
Oil Supply Pipe-To-Engine Nut .................... 14 (19)
Oil Supply Pipe-To-Turbocharger Nut .............. 14 (19)
Plenum-To-Intake Manifold Bolts ............ 11-15 (15-20)
Throttle Body .................................... 14 (19)
Turbocharger-To-Exhaust Manifold Bolt/Nut
Step 1 ......................................... 21 (29)
Step 2 ........................ Additional 60-70 Degrees
Water Pipe-To-Turbocharger
Eclipse .................................. 25-36 (34-49)
3000GT ......................................... 22 (30)
INCH Lbs. (N.m)
Camshaft Position Sensor .......................... 80 (9)
Crankshaft Position Sensor ........................ 80 (9)
Distributor Hold-Down Bolt ...................... 106 (12)
Engine Cover ............................. 22-40 (2.5-4.5)
Fuel Pressure Regulator ........................... 80 (9)
Fuel Pump Nuts .................................. 22 (2.5)
Fuel Rail Bolts ....................... 80-106 (9.0-12.0)
TP Sensor Screws ......................... 13-22 (1.5-2.5)
Wastegate Actuator Bolts ............... 80-106 (9.0-12.0)
\
\
\
\
\
\
Page 1039 of 1501
Fig. 11: Identifying Power Window Connector Terminals (3000GT -
Sub-Switch)
Courtesy of Mitsubishi Motor Sales of America
REMOVAL & INSTALLATION
POWER WINDOW MOTOR
Removal & Installation
Remove door trim panel and waterproof shield. Remove glass
retaining screws and glass. See Fig. 12. Remove motor and slider
assembly retaining bolts. Remove motor and slider assembly from door.
To install, reverse removal procedure.
Fig. 12: Removing Power Window Motor & Slider Assembly (Typical)
Courtesy of Mitsubishi Motor Sales of America
WIRING DIAGRAMS
Page 1074 of 1501
SEAT ASSEMBLY
Removal & Installation (Functioning Power Seat)
With ignition on, move seat fully rearward. Remove front seat
anchor covers and remove nuts. Move seat fully forward. Remove rear
seat anchor covers and remove bolts. Turn ignition off. Disconnect
electrical harness connectors. Remove seat assembly. To install,
reverse removal procedure.
Removal & Installation (Malfunctioning Power Seat)
1) Removal of seat assembly front or rear mounting bolt is
not possible due to malfunction of slide motor, slide switch or frozen
slide rails. If seat is stuck in forward position, go to next step. If
seat is stuck in rearward position, go to step 3).
2) Remove rear seat anchor covers and mounting bolts. Remove
adjuster screw nut housing mounting bolt. See Fig. 7. Both adjuster
screw nut housings mount to center of slider frame rail. Insert
screwdriver blade between housing nut and rail. Lift and rotate
housing nut. Slide seat back and remove front anchor nuts. Once seat
is repaired, install housing nut bolts.
3) Lift up front seat cushion cover to expose slide motor.
Remove slide motor mounting bolts. If seat assembly cannot be moved
forward, remove slide motor bracket mounting bolts. Move seat forward
and remove rear anchor bolts. Once seat is repaired, install slide
motor bracket mounting bolts.
Fig. 7: Disconnecting Nut Housing (Typical)
Courtesy of Mitsubishi Motor Sales of America
WIRING DIAGRAMS
Page 1087 of 1501
ARMATURE TEST
Ensure armature is not grounded. Place armature in growler.
Hold a thin steel blade parallel and just above armature while slowly
rotating armature in growler. A shorted armature will cause blade to
vibrate and be attracted to core. Using an ohmmeter, check continuity
between armature coil cores and commutator segments (small diameter
end of armature). Continuity should not exist. Check for continuity
between segments. Continuity should exist. Replace armature as
necessary.
BRUSH HOLDER TEST
Using an ohmmeter, check continuity between brush holder
plate and brush holder. Continuity should not exist. Replace brush
holder as necessary.
REMOVAL & INSTALLATION
NOTE: On Montero with A/T, it may be necessary to disconnect
transmission oil cooler line for starter removal.
Removal & Installation
Disconnect negative battery cable. If necessary, raise
vehicle on hoist. Remove starter mounting bolts and starter. To
install, reverse removal procedure.
OVERHAUL
Check commutator for out-of-round and proper amount of
undercut. Replace or repair armature if not within specification. See
STARTER SPECIFICATIONS table. Ensure brushes are not worn beyond wear
line (outer line closest to commutator contact surface). Check pinion
gap. See PINION GAP MEASUREMENT under BENCH TESTING. See Figs. 5 and
6.
Fig. 5: Exploded View Of Direct Drive Starter (Typical)
Courtesy of Mitsubishi Motor Sales of America
Page 1089 of 1501
![MITSUBISHI MONTERO 1998 Repair Manual STARTER SPECIFICATIONS TABLE \
\
\
\
\
\
Application](/img/19/57333/w960_57333-1088.png "MITSUBISHI MONTERO 1998 Repair Manual STARTER SPECIFICATIONS TABLE \
\
\
\
\
\
Application")
STARTER SPECIFICATIONS TABLE \
\
\
\
\
\
Application In. (mm)
Commutator Maximum Runout ..................... .004 (.10)
Commutator Minimum Diameter
Diamante ................................... 1.23 (31.2)
Eclipse
Direct Drive Type ................................ (1)
Gear Reduction Type ...................... 1.12 (28.4)
Galant ..................................... 1.12 (28.4)
Mirage
Direct Drive Type ........................ 1.22 (31.4)
Gear Reduction Type ...................... 1.12 (28.4)
Montero & Montero Sport .................... 1.13 (28.8)
3000GT ..................................... 1.12 (28.4)
Commutator Undercut Depth ..................... .020 (.51)
Pinion Gap .......................... .020-.079 (.51-2.01)
( 1) - Information is not available from manufacturer at time
of publication.
\
\
\
\
\
\
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
\
Application Ft. Lbs. (N.m)
Starter-To-Block Bolts
Diamante ....................................... 23 (31)
Eclipse
2.0L Non-Turbo ............................... 40 (54)
2.0L Turbo & 2.4L ............................ 22 (30)
Galant ......................................... 22 (30)
Mirage ......................................... 36 (49)
Montero & Montero Sport .................. 19-24 (26-33)
3000GT ......................................... 23 (31)
\
\
\
\
\
\
WIRING DIAGRAMS
Page 1141 of 1501
column switch. To install, reverse removal procedure.
Removal & Installation (Eclipse)
Remove air bag module. See AIR BAG RESTRAINT SYSTEMS article.
Remove horn pad and steering wheel. Remove hood lock release handle.
Remove column pad and upper and lower column covers. See Fig. 6.
Remove A/C-heater system lap cooler duct and foot shower duct. Remove
steering column switch. To install, reverse removal procedure.
Removal & Installation (Galant)
Remove air bag module. See AIR BAG RESTRAINT SYSTEMS article.
Remove steering wheel. Remove column pad. Remove foot duct. Remove
upper and lower steering column covers. See Fig. 11. Remove steering
column switch. To install, reverse removal procedure.
Removal & Installation (Mirage)
Remove air bag module. See AIR BAG RESTRAINT SYSTEMS article.
Remove steering wheel. Remove hood release handle. Remove knee
protector. Remove upper and lower steering column covers. See Fig. 15.
Remove steering column switch. To install, reverse removal procedure.
Removal & Installation (Montero)
Remove air bag module. See AIR BAG RESTRAINT SYSTEMS article.
Remove steering wheel. Remove foot duct. Remove lower instrument panel
cover. Remove upper and lower steering column covers. See Fig. 19.
Remove steering column switch. To install, reverse removal procedure.
Removal & Installation (Montero Sport)
Remove air bag module. See AIR BAG RESTRAINT SYSTEMS article.
Remove steering wheel. Remove instrument panel lower cover. Remove
upper and lower steering column covers. See Fig. 25. Remove steering
column switch. To install, reverse removal procedure.
Removal & Installation (3000GT)
Remove air bag module. See AIR BAG RESTRAINT SYSTEMS article.
Remove steering wheel. Remove knee protector. Remove upper and lower
steering column covers. Remove A/C-heater system lap cooler duct and
foot duct. Remove left or right steering column switch. See Fig. 31.
To install, reverse removal procedure.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
\
Application Ft. Lbs. (N.m)
Steering Wheel Nut
Diamante, Montero, Montero Sport
& 3000GT ...................................... 29 (39)
Eclipse, Galant & Mirage ....................... 30 (41)
INCH Lbs. (N.m)
Air Bag Module Bolts/Nuts
Diamante, Eclipse & Mirage .................... 53 (6.0)
Galant & Montero .............................. 80 (9.0)
Montero Sport ................................. 78 (8.8)
3000GT ....................................... 39 (4.4)
\
\
\
\
\
\
WIRING DIAGRAMS
Page 1152 of 1501
IGNITION SWITCH
Removal & Installation
1) Remove upper and lower steering column covers. Disconnect
harness connector from ignition switch. Using hacksaw, cut slots in
bolt heads of lock assembly. Using screwdriver, remove bolts and lock
assembly.
2) To install, reverse removal procedure. Tighten new bolts
until heads of bolts sheer off.
STEERING COLUMN
WARNING: Failure to follow air bag service precautions may result in
air bag deployment and personal injury. See AIR BAG SERVICE
PRECAUTIONS. Follow all service precautions before
attempting repairs. After component replacement, perform a
system operational check to ensure proper system operation.
CAUTION: Applying excessive pressure or causing impact to steering
shaft during service may cause column to collapse. Before
removing steering column, ensure wheels are in
straight-ahead position. Note steering wheel location for
installation reference.
Removal
1) Remove steering wheel. Remove combination switch and
ignition switch (if necessary). See STEERING WHEEL under
REMOVAL & INSTALLATION .
2) Remove lower instrument panel cover and air duct.
Disconnect all electrical connections. Disconnect brake pedal return
spring (if equipped). Disconnect gearshift control cable.
3) Remove bolts for dust cover at firewall. Remove bolt from
clamp at steering gear. Remove steering column bolts and remove
steering column.
Installation
To install, reverse removal procedure. Apply sealant (3M ATD
8663) to dust cover bolts before installing. Tighten bolts to
specification. See TORQUE SPECIFICATIONS .
OVERHAUL
STEERING COLUMN
WARNING: Failure to follow air bag service precautions may result in
air bag deployment and personal injury. See AIR BAG SERVICE
PRECAUTIONS. Follow all service precautions before
attempting repairs. After component replacement, perform a
system operational check to ensure proper system operation.
NOTE: Vehicle steering column is not repairable. See below for
joint assembly and steering lock removal and installation.
Disassembly
Remove steering column from vehicle. See STEERING COLUMN
under REMOVAL & INSTALLATION . Remove clamp bolt from joint assembly.
See Fig. 1 . Remove assembly. Remove lower boot, upper boot and dust
cover from joint assembly. To remove steering lock, use a hacksaw to
cut bolts at steering lock bracket side. Remove steering lock and
bracket.