bolts MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1417 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Brakes dragging See BRAKES article \
\
\
\
\
\](/img/19/57333/w960_57333-1416.png "MITSUBISHI MONTERO 1998 Service Manual Brakes dragging See BRAKES article \
\
\
\
\
\")
Brakes dragging See BRAKES article \
\
\
\
\
\
\
Instability Low or uneven tire Inflate to proper
pressure pressure
Loose or worn wheel See FRONT SUSPENSION
bearings article
Loose or worn idler arm See FRONT SUSPENSION
bushing article
Loose or worn strut See FRONT SUSPENSION
bushings article
Incorrect front wheel See WHEEL ALIGNMENT
alignment article
Steering gear not See MANUAL STEERING
centered GEARS article
Springs or shock Check and replace if
necessary
Improper cross shaft See MANUAL STEERING
GEARS article
\
\
\
\
\
\
\
POWER STEERING TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC POWER STEERING TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Rattle or Pressure hoses touching Adjust to proper
Chucking Noise engine parts clearance
Loose Pitman shaft Adjust or replace if
necessary
Tie rods ends or Pitman Tighten and check system
arm loose
Rack and pinion mounts Tighten all mounting
loose bolts
Free play in worm and See POWER STEERING GEAR
article
Loose sector shaft or See POWER STEERING GEAR
thrust bearing adjustment
Free play in pot coupling See STEERING COLUMN
article
Page 1421 of 1501
Free play in pot coupling See POWER STEERING PUMP
article
Steering gear coupling See POWER STEERING PUMP
loose on shaft article
Steering disc mounting Tighten or replace if
bolts loose necessary
Coupling loose on worm Tighten or replace if
shaft necessary
Improper sector shaft See POWER STEERING GEAR
adjustment article
Excessive worm piston See POWER STEERING GEAR
side play article
Damaged valve lever See POWER STEERING GEAR
article
Universal joint loose Tighten or replace if
necessary
Defective rotary valve See POWER STEERING GEAR
article
\
\
\
\
\
\
\
No Power When Sticking flow control See POWER STEERING PUMP
Parking valve article
Insufficient pump See POWER STEERING PUMP
pressure output article
Excessive internal pump See POWER STEERING PUMP
leakage article
Excessive internal gear See POWER STEERING PUMP
leakage article
Flange rubs against gear See STEERING COLUMN
adjust plug article
Loose pump belt Adjust or replace if
necessary
Low fluid level Check and add proper
amount of fluid
Engine idle too low Adjust to correct
setting
Steering gear-to-column See STEERING COLUMN
misaligned article
\
\
\
\
\
\
\
No Power, Left turn reaction seal See POWER STEERING GEAR
Left Turn "O" ring worn article
Left turn reaction seal See POWER STEERING GEAR
damaged/missing article
Cylinder head "O" ring See POWER STEERING PUMP
damaged article
\
\
\
\
\
\
\
Page 1424 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Improper gate plate See STEERING COLUMN
adjustment article
\
\
\
\](/img/19/57333/w960_57333-1423.png "MITSUBISHI MONTERO 1998 Service Manual Improper gate plate See STEERING COLUMN
adjustment article
\
\
\
\")
Improper gate plate See STEERING COLUMN
adjustment article
\
\
\
\
\
\
\
Excess Play in Instrument panel bracket Tighten bolts and check
Column bolts loose bracket
Broken weld nut on jacket See STEERING COLUMN
article
Instrument bracket capsule See STEERING COLUMN
sheared article
Column bracket/jacket Tighten bolts and check
bolts loose bracket
\
\
\
\
\
\
\
Steering Locks Release lever mechanism See STEERING COLUMN
in Gear article
\
\
\
\
\
\
\
SUSPENSION TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC SUSPENSION TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Front End Noise Loose or worn wheel See Wheel Bearing
Adjustment in
SUSPENSION
Worn shocks or shock Replace struts or strut
mountings mountings
Worn struts or strut Replace struts or strut
mountings mountings
Loose or worn lower control See SUSPENSION
arm
Loose steering gear-to- See STEERING
frame bolts
Worn control arm bushings See SUSPENSION
Ball joints not lubricated Lubricate ball joints &
see Ball Joint Checking
in SUSPENSION
\
\
\
\
\
\
\
Front Wheel Tires or wheels out of Check tire balance
Shake, Shimmy, balance
or Vibration
Incorrect wheel alignment See WHEEL ALIGNMENT
Drive shaft unbalanced Check drive shaft
balance
Page 1425 of 1501
Loose or worn wheel See WHEEL ALIGNMENT
bearings
Loose or worn tie rod ends See SUSPENSION
Worn upper ball joints See Ball Joint Checking
in SUSPENSION
Worn shock absorbers Replace shock absorbers
Worn strut bushings Replace strut bushings
\
\
\
\
\
\
\
Car Pulls to Mismatched or uneven tires Check tire condition
One Side
Broken or sagging springs See SUSPENSION
Loose or worn strut See SUSPENSION
bushings
Improper wheel alignment See WHEEL ALIGNMENT
Improper rear axle Check rear axle
alignment alignment
Power steering gear See STEERING
unbalanced
Front brakes dragging See BRAKES
\
\
\
\
\
\
\
Abnormal Tire Unbalanced tires Check tire balance &
Wear rotation
Sagging or broken springs See SUSPENSION
Incorrect front end See WHEEL ALIGNMENT
alignment
Faulty shock absorbers Replace chock absorbers
\
\
\
\
\
\
\
Scuffed Tires Toe-In incorrect See WHEEL ALIGNMENT
Suspension arm bent or See appropriate
twisted SUSPENSION article
\
\
\
\
\
\
\
Springs Bottom Bent or broken springs See SUSPENSION
or Sag
Leaking or worn shock Replace shock absorbers
absorbers
Frame misalignment Check frame for damage
\
\
\
\
\
\
\
Spring Noises Loose "U" Bolts See SUSPENSION
Loose or worn bushings See SUSPENSION
Worn or missing interliners See SUSPENSION
\
\
\
\
\
\
\
Shock Absorber Loose shock mountings Check & tighten
Noise mountings
Worn bushings Replace bushings
Page 1426 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Air in system Bleed air from system
Undercoating on shocks Remove undercoating
\
\
\](/img/19/57333/w960_57333-1425.png "MITSUBISHI MONTERO 1998 Service Manual Air in system Bleed air from system
Undercoating on shocks Remove undercoating
\
\
\")
Air in system Bleed air from system
Undercoating on shocks Remove undercoating
\
\
\
\
\
\
\
Car Leans or Loose stabilizer bar See SUSPENSION
Sways on Corners
Faulty shocks or mountings Replace shocks or
mountings
Broken or sagging springs See SUSPENSION
\
\
\
\
\
\
\
Shock Absorbers Worn seals or reservoir See SUSPENSION
Leaking tube crimped
\
\
\
\
\
\
\
Broken Springs Loose "U" bolts See SUSPENSION
Inoperative shock absorbers Replace shock absorbers
\
\
\
\
\
\
\
WHEEL ALIGNMENT TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC WHEEL ALIGNMENT TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Premature Tire Improper tire inflation Check tire pressure
Wear
Front alignment out of See ALIGNMENT SPECS in
tolerance WHEEL ALIGNMENT section
Suspension components worn See SUSPENSION section
Steering system components See STEERING section
worn
Improper standing height See WHEEL ALIGNMENT
Uneven or sagging springs See SUSPENSION section
Bent wheel See WHEEL ALIGNMENT
Improper torsion bar See SUSPENSION section
adjustment
Loose or worn wheel See WHEEL BEARING ADJ.
bearings in SUSPENSION section
Worn or defective shock Replace shock absorbers
Tires out of balance Check tire balance
\
\
\
\
\
\
\
Pulls to One Improper tire inflation Check tire pressure
Side
Brake dragging See BRAKE section
Page 1465 of 1501
WHEEL ALIGNMENT PROCEDURES
CAMBER ADJUSTMENT
Except Montero, Montero Sport & 3000GT
Camber is preset and cannot be adjusted. Check camber. See
appropriate table under WHEEL ALIGNMENT SPECIFICATIONS . If camber is
not within specification, replace damaged or bent parts.
Montero & Montero Sport
1) Check camber. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If camber is not within specification,
remove shock absorber mounting nut and lock nut.
CAUTION: Difference in shim thickness between front and rear must not
exceed 0.16" (4.0 mm). DO NOT use more than 3 shims at
onelocation.
2) Compress shock absorber, and loosen upper arm mounting
bolts and nuts. Adjust camber by increasing or decreasing shims
between upper arm shaft and crossmember. See Fig. 6.
Fig. 6: Adjusting Camber & Caster (Montero Sport Shown; Montero Is
Similar)
Courtesy of Mitsubishi Motor Sales of America.
3000GT
Check camber. See WHEEL ALIGNMENT SPECIFICATIONS (3000GT)
table. If camber is not within specification, loosen eccentric cam
nut. Rotate eccentric cam bolt to obtain correct camber. See Fig. 7.
Each marking represents a change of .12-.25 degree of camber.
Page 1466 of 1501
Fig. 7: Adjusting Camber (3000GT)
Courtesy of Mitsubishi Motor Sales of America.
CASTER ADJUSTMENT
Except Montero & Montero Sport
Check caster. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If caster is not within specification,
replace damaged or bent parts.
Montero & Montero Sport
1) Check caster. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If caster is not within specification,
remove shock absorber mounting nut and lock nut.
CAUTION: Difference in shim thickness between front and rear must not
exceed .16" (4.0 mm). DO NOT use more than 3 shims at one
location.
2) Compress shock absorber, and loosen upper arm mounting
bolts and nuts. Adjust caster by increasing or decreasing shims
between upper arm shaft and crossmember. See Fig. 6.
TOE-IN ADJUSTMENT
Front
Check front toe-in. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If front toe-in is not within
specification, remove clips. Turn tie rods or turnbuckles same amount,
but in opposite directions. Recheck front toe-in.
Rear (Montero & Montero Sport)
Check rear toe-in. See appropriate table under
Page 1467 of 1501
WHEEL ALIGNMENT SPECIFICATIONS. If rear toe-in is not within
specification, replace damaged or bent parts.
Rear (3000GT AWD)
Check rear toe-in. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If rear toe-in is not within
specification, loosen both trailing arm eccentric cam nuts. Turn
trailing arm eccentric cam bolts equal amount to obtain correct rear
toe-in. See Fig. 8.
Rear (Except Montero, Montero Sport & 3000GT AWD)
Check rear toe-in. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If rear toe-in is not within
specification, loosen both assist link eccentric cam nuts. Turn assist
link eccentric cam bolts equal amount to obtain correct rear toe-in.
See Fig. 9 .
Fig. 8: Adjusting Rear Toe-In (3000GT AWD)
Courtesy of Mitsubishi Motor Sales of America.
Page 1475 of 1501
subtracted by the width measured at the front of the tires at about
spindle height. A positive figure would indicate toe-in and a negative
figure would indicate toe-out. If the distance between the front and
rear of the tires is the same, toe measurement would be zero. To
adjust:
1) Measure toe-in with front wheels in straight ahead
position and steering wheel centered. To adjust toe-in, loosen clamps
and turn adjusting sleeve or adjustable end on right and left tie
rods. See Figs. 2 and 5.
2) Turn equally and in opposite directions to maintain
steering wheel in centered position. Face of tie rod end must be
parallel with machined surface of steering rod end to prevent binding.
3) When tightening clamps, make certain that clamp bolts are
positioned so there will be no interference with other parts
throughout the entire travel of linkage.
Fig. 5: Wheel Toe-In (Dimension A Less Dimension B)
TOE-OUT ON TURNS
1) Toe-out on turns (turning radius) is a check for bent or
damaged parts, and not a service adjustment. With caster, camber, and
toe-in properly adjusted, check toe-out with weight of vehicle on
wheels.
2) Use a full floating turntable under each wheel, repeating
test with each wheel positioned for right and left turns. Incorrect
toe-out generally indicates a bent steering arm. Replace arm, if
necessary, and recheck wheel alignment.
Page 1489 of 1501
1) Remove wiper switch from instrument panel and disconnect
wiper switch. Place wiper switch in OFF position. Continuity should
exist between terminals No. 4 and 5. See Fig. 12. Place wiper switch
in ON position. Continuity should exist between terminals No. 5 and 6.
2) Place wiper switch in INT position. Continuity should
exist between terminals No. 4 and 5, and between terminals No. 7 and
8. Depress washer switch. Continuity should exist between terminals
No. 2 and 6. Continuity between terminals No. 1 and 3 should exist in
all positions (light circuit).
REMOVAL & INSTALLATION
FRONT WIPER MOTOR
Removal & Installation
Remove wiper motor bolts. Pull motor out slightly. Disconnect
wiper linkage from motor assembly and remove motor. To install,
reverse removal procedure.
FRONT WIPER SWITCH
NOTE: Front wiper switch is part of combination switch on steering
column. See STEERING COLUMN SWITCHES article.
REAR WIPER MOTOR
Removal & Installation
Remove wiper blade and arm assembly. Remove tailgate trim, 2
bolts and wiper motor. To install, reverse removal procedure. Ensure
grommet is in good condition.
REAR WIPER SWITCH
Removal & Installation
Pry rear wiper switch from instrument panel and disconnect
wiper switch wiring connector. To install switch, reverse removal
procedure.
WIRING DIAGRAMS