oil capacities MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 37 of 1501
Only NEW, moisture-free refrigerant oil should be used in the
air conditioning system. This oil is highly refined and dehydrated so
moisture content is less than 10 parts per million. The oil container
must be tightly closed at all times when not in use, or moisture from
the air will be absorbed into the refrigerant oil.
SERVICING PRECAUTIONS
DISCHARGING SYSTEM
Discharge A/C system, using approved refrigerant
recovery/recycling equipment that meets SAE J2210 requirements. Always
follow recovery/recycling equipment manufacturer's instructions. After
refrigerant recovery process is completed, replace any refrigerant oil
removed with the same amount of NEW refrigerant oil.
DISCONNECTING LINES & FITTINGS
After system is discharged, carefully clean area around all
fittings to be opened. Always use 2 wrenches when tightening or
loosening fittings. Some refrigerant lines are connected with a
coupling. Special tools may be required to disconnect lines. Cap or
plug all openings as soon as lines are removed. DO NOT remove shipping
caps from replacement components until ready to install.
CONNECTING LINES & FITTINGS
NOTE: Ensure all replacement component connections match
connections of system being worked on.
Always use a NEW gasket or "O" ring when connecting lines or
fittings. Coat "O" ring with NEW refrigerant oil and ensure it is not
twisted during installation. Always use two wrenches to prevent damage
to lines and fittings.
PLACING SYSTEM IN OPERATION
After component service or replacement has been completed and
all connections have been made, thoroughly evacuate system with a
vacuum pump. Charge system with proper amount of refrigerant and
perform leak test. See REFRIGERANT OIL & REFRIGERANT SPECIFICATIONS
table for system capacities. Ensure there are no leaks at any fitting
that has been opened. After system has been leak tested, check system
performance.
NIPPONDENSO 10-CYL.
Eclipse 2.0L Non-Turbo & Montero
Replacement compressor is shipped with NEW refrigerant oil.
Drain, measure and discard refrigerant oil from old compressor. Drain
NEW refrigerant oil from replacement compressor equal to difference
between amount drained from old compressor and amount shipped in
replacement compressor. If any other components are replaced, add NEW
refrigerant oil as specified. See COMPONENT REFRIGERANT OIL CAPACITIES
(MITSUBISHI - NIPPONDENSO 10-CYL.) table.
COMPONENT REFRIGERANT OIL CAPACITIES TABLE (NIPPONDENSO)
\
\
\
\
\
\
Component Ounces
Compressor ( 1)
Page 38 of 1501
Eclipse 2.0L Non-Turbo ............................. 3.4
Montero ............................................ 4.1
Condenser ............................................ 1.4
Evaporator ........................................... 1.4
Receiver-Drier ....................................... 0.3
Suction Hose ......................................... 0.3
(1) - If replacement compressor is shipped without
refrigerant oil, add same amount of NEW refrigerant
oil to replacement compressor that was drained from
old compressor.
\
\
\
\
\
\
SANDEN SCROLL
Diamante, Eclipse 2.0L Turbo & 2.4L, Galant, Mirage, Montero
Sport and 3000GT
Replacement compressor is shipped with NEW refrigerant oil.
Drain, measure and discard refrigerant oil from old compressor. Drain
NEW refrigerant oil from replacement compressor equal to difference
between amount drained from old compressor and amount shipped in
replacement compressor. If any other components are replaced, add NEW
refrigerant oil as specified. See COMPONENT REFRIGERANT OIL CAPACITIES
(SANDEN SCROLL) table.
COMPONENT REFRIGERANT OIL CAPACITIES TABLE (SANDEN SCROLL)
\
\
\
\
\
\
Component Ounces
Compressor ( 1)
Diamante, Eclipse 2.0L Turbo & 2.4L & Galant ... 5.7-6.4
Mirage ............................................. 4.4
3000GT ............................................. 5.4
Condenser
Diamante, Eclipse 2.0L Turbo & 2.4L,
Galant, Mirage & 3000GT ............................ 0.5
Evaporator
Diamante, Eclipse 2.0L Turbo & 2.4L,
Galant, Mirage & 3000GT ............................ 2.0
Receiver-Drier
Diamante, Eclipse 2.0L Turbo & 2.4L,
Galant, Mirage & 3000GT ............................ 0.3
Refrigerant Lines
Diamante, Eclipse 2.0L Turbo & 2.4L,
Galant, Mirage & 3000GT ............................ 0.3
( 1) - If replacement compressor is shipped without
refrigerant oil, add same amount of NEW refrigerant
oil to replacement compressor that was drained from
old compressor.
\
\
\
\
\
\
Page 965 of 1501
![MITSUBISHI MONTERO 1998 Service Manual FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\](/img/19/57333/w960_57333-964.png "MITSUBISHI MONTERO 1998 Service Manual FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\")
FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\
Item Condition Specification
\
\
\
\
\
\
\
\f
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1)
\
\
\
\
\
\
\f
Oil Filter 0.32 Qts. (0.3L)
\
\
\
\
\
\
\f
Oil Cooler 0.32 Qts. (0.3L)
\
\
\
\
\
\
\
\f
Power Drained 1.1 Qts. (1.0L)
Steering
\
\
\
\
\
\
\
\f
Automatic Drained 8.9 Qts. (8.5L)
Transmission
\
\
\
\
\
\
\
\f
Manual Drained 3.3 Qts. (3.2L)
Transmission
\
\
\
\
\
\
\
\f
Transfer Case Drained 2.6 Qts. (2.5L)
\
\
\
\
\
\
\
\f
Front Axle Drained 1.3 Qts. (1.2L)
\
\
\
\
\
\
\
\f
Rear Axle Drained 3.3 Qts. (3.2L)
\
\
\
\
\
\
\
\f
A/C Drained 27 oz (760 g)
Refrigerant
\
\
\
\
\
\
\
\f
Fuel Tank Capacity 24 gal (92L)
\
\
\
\
\
\
\
\f
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE
\
\
\
\
\
\
Wheel Size Tire Size
15 x 6JJ (Steel or Aluminum) .................. P235/75R15
15 X 7JJ (Aluminum) ........................... P265/70R15
\
\
\
\
\
\
WHEEL TIGHTENING
Page 1047 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
REPLACE](/img/19/57333/w960_57333-1046.png "MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
REPLACE")
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
15,000 MILE (24,000 KM) NORMAL SERVICE
15,000 MILE (24,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Disc Brake Pads (
3)
\b
\
\
\
\
\
\
\
Brake Hoses (
3)
\b
\
\
\
\
\
\
\
Drive Shaft Boots (
3)
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
(
3) - Or inspect every year.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
Page 1048 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \b\
\
\
\
\
\
\
Material Condition](/img/19/57333/w960_57333-1047.png "MITSUBISHI MONTERO 1998 Service Manual \b\
\
\
\
\
\
\
Material Condition")
\b\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
Brake Fluid All DOT 3 Or DOT 4
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
22,500 MILE (36,000 KM) NORMAL SERVICE
22,500 MILE (36,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
Page 1049 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \b\
\
\
\
\
\
\
Engine Oil Oil Pan](/img/19/57333/w960_57333-1048.png "MITSUBISHI MONTERO 1998 Service Manual \b\
\
\
\
\
\
\
Engine Oil Oil Pan")
\b\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
30,000 MILE (48,000 KM) NORMAL SERVICE
30,000 MILE (48,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
SERVICE
\b
\
\
\
\
\
\
\
Ball Joints With Grease Nipple (
6)
\b
\
\
\
\
\
\
\
Propeller Shaft Joints (
6)
\b
\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Fuel Hoses (
3)
\b
\
\
\
\
\
\
\
Drive Belt (For Generator, Water Pump, Power Steering Pump)
\b
\
\
\
\
\
\
\
Manual Transmission Oil
\b
\
\
\
\
\
\
\
Transfer Oil
\b
\
\
\
\
\
\
\
Disc Brake Pads (
4)
\b
\
\
\
\
\
\
\
Brake Hoses (
4)
\b
\
\
\
\
\
\
\
Ball Joint & Steering Linkage Seals (
3)
\b
\
\
\
\
\
\
\
Drive Shaft Boots (
4)
\b
\
\
\
\
\
\
\
Exhaust System (
3)
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
Engine Coolant
\b
\
\
\
\
\
\
\
Automatic Transmission Fluid
\b
\
\
\
\
\
\
\
Rear Axle Oil
\b
\
\
\
\
\
\
\
Air Cleaner Filter
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
Page 1050 of 1501
(3) - Or inspect every 2 years.
(
4) - Or inspect every year.
(
5) - Or change every 2 years.
(
6) - Or lubricate grease every 2 years.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\b
\
\
\
\
\
\
\
Manual All API Classification GL-4
Transmission SAE 75W-85W Or 75W-90
\b
\
\
\
\
\
\
\
Automatic All "ATF DEXRON II" Or
Transmission Equivalent
\b
\
\
\
\
\
\
\
Brake Fluid All DOT 3 Or DOT 4
\b
\
\
\
\
\
\
\
Rear Axle All API Classification GL-5
Or Higher (
2)
\b
\
\
\
\
\
\
\
Transfer Case All API Classification GL-4
SAE 75W-85W Or 75W-90
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
(
2) - SAE90, 85W-90, 80W-90 may be used in temperatures above
-10 F (-23 C). SAE 80W, 80W-90 may be used in temperatures
from -30 F (-34 C) to -10 F (-23 C). SAE 75W may be used
in temperatures below -30 F (-34 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
Engine Drained; With Reserve Tank 10 Qts. (9.5L)
Coolant
\b
\
\
\
\
\
\
\
Automatic Drained 8.9 Qts. (8.5L)
Transmission
\b
\
\
\
\
\
\
\
Manual Drained 3.3 Qts. (3.2L)
Transmission
\b
\
\
\
\
\
\
\
Rear Axle Drained 3.3 Qts. (3.2L)
\b
\
\
\
\
\
\
\
Transfer Case Drained 2.6 Qts. (2.5L)
Page 1051 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \b\
\
\
\
\
\
\
(
1) - Capacities are recommended or calcul](/img/19/57333/w960_57333-1050.png "MITSUBISHI MONTERO 1998 Service Manual \b\
\
\
\
\
\
\
(
1) - Capacities are recommended or calcul")
\b\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
37,500 MILE (60,000 KM) NORMAL SERVICE
37,500 MILE (60,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
45,000 MILE (72,000 KM) NORMAL SERVICE
45,000 MILE (72,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Disc Brake Pads (
3)
\b
\
\
\
\
\
\
\
Page 1052 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Brake Hoses (3)
\b
\
\
\
\
\
\](/img/19/57333/w960_57333-1051.png "MITSUBISHI MONTERO 1998 Service Manual Brake Hoses (3)
\b
\
\
\
\
\
\")
Brake Hoses (3)
\b
\
\
\
\
\
\
\
Drive Shaft Boots (
3)
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
(
3) - Or inspect every year.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
Brake Fluid All DOT 3 Or DOT 4
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
52,500 MILE (84,000 KM) NORMAL SERVICE
52,500 MILE (84,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
\b
\
\
\
\
\
\
\
Page 1053 of 1501
![MITSUBISHI MONTERO 1998 Service Manual LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\](/img/19/57333/w960_57333-1052.png "MITSUBISHI MONTERO 1998 Service Manual LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\")
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
60,000 MILE (96,000 KM) NORMAL SERVICE
60,000 MILE (96,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
SERVICE
\b
\
\
\
\
\
\
\
Ball Joints With Grease Nipple (
6)
\b
\
\
\
\
\
\
\
Propeller Shaft Joints (
6)
\b
\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Fuel Hoses (
3)
\b
\
\
\
\
\
\
\
Fuel System (Tank, Pipe Line, Connection & Fuel Tank Filler
Tube Cap) (
3)
\b
\
\
\
\
\
\
\
Evaporative Emission Control System (Except Evaporative
Emission Canister) (
7)
\b
\
\
\
\
\
\
\
Drive Belt (For Generator, Water Pump, Power Steering Pump)
\b
\
\
\
\
\
\
\
Manual Transmission Oil
\b
\
\
\
\
\
\
\
Transfer Oil
\b
\
\
\
\
\
\
\
Disc Brake Pads (
4)
\b
\
\
\
\
\
\
\
Brake Hoses (
4)
\b
\
\
\
\
\
\
\
Ball Joint & Steering Linkage Seals (
3)