wheel MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 28 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\b\
\
\
\
\
\
EAC Electric Assist Choke](/img/19/57333/w960_57333-27.png "MITSUBISHI MONTERO 1998 Service Manual \
\b\
\
\
\
\
\
EAC Electric Assist Choke")
\
\b\
\
\
\
\
\
EAC Electric Assist Choke
EACV Electric Air Control Valve
EBCM Electronic Brake Control Module
ECA Electronic Control Assembly
ECAT Electronically Controlled Automatic Transaxle
ECM Electronic Control Module
ECT Engine Coolant Temperature Sensor
ECU Electronic Control Unit or Engine Control Unit
EDF Electric Drive Fan relay assembly
EDIS Electronic Distributorless Ignition System
EEC Electronic Engine Control
EECS Evaporative Emission Control System
EEPROM Electronically Erasable PROM
EFE Early Fuel Evaporation
EFI Electronic Fuel Injection
EGO Exhaust Gas Oxygen sensor (see HEGO)
EGR Exhaust Gas Recirculation system
EGRC EGR Control solenoid or system
EGRV EGR Vent solenoid or system
EMR Emission Maintenance Reminder Module
ESA Electronic Spark Advance
ESC Electronic Spark Control
EST Electronic Spark Timing
ETR Emergency Tensioning Retractor
EVAP Fuel Evaporative System
EVIC Electronic Vehicle Information Center
EVO Electronic Variable Orifice
EVP EGR Valve Position Sensor
EVR EGR Valve Regulator
EVRV Electronic Vacuum Regulator Valve
Elect. Electronic
Eng. Engine
Evap. Evaporative
Exc. Except
\
\
\
\
\
\
\
\f
"F" ABBREVIATION TABLE
"F" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
F Fahrenheit (Degrees)
F/B Fuse Block
FBC Feedback Carburetor
FI Fuel Injector or Fuel Injection
FICD Fast Idle Control Device
FIPL Fuel Injector Pump Lever
FP Fuel Pump
FPM Fuel Pump Monitor
FPR-VSV Fuel Pressure Regulator Vacuum Switching Valve
FWD Front Wheel Drive
Fed. Federal
Ft. Lbs. Foot Pounds
\
\
\
\
\
\
\
\f
"G" ABBREVIATION TABLE
"G" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
Page 33 of 1501
RVB Rear Vacuum Break
RWAL Rear Wheel Anti-Lock Brake
RWD Rear Wheel Drive
Recirc. Recirculate or Recirculation
Reg. Regulator
Rly. Relay
\
\
\
\
\
\
\
\f
"S" ABBREVIATION TABLE
"S" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
SAW Spark Angle Word
SBC Single Bed Converter
SBEC Single Board Engine Controller
SC Super Charged
SCC Spark Control Computer
SCS Air Suction Control Solenoid
SDM Supplemental Restraint System Diagnostic Module
SDU SRS Diagnostic Unit
SEN Sensor
SES Service Engine Soon
SFI Sequential (Port) Fuel Injection
SIG RTN Signal Return circuit
SIL Shift Indicator Light
SIR Supplemental Inflatable Restraint
SMEC Single Module Engine Controller
SOHC Single Overhead Cam
SOL or Sol. Solenoid
SPFI Sequential Port Fuel Injection
SPK Spark Control
SPOUT Spark Output Signal
SRS Supplemental Restraint System (Air Bag)
SS 3/4-4/3 Shift Solenoid circuit
SSI Solid State Ignition
STAR Self-Test Automatic Readout
STI Self Test Input circuit
STO Self-Test Output
SUB-O2 Sub Oxygen Sensor
Sen. or Sens. Sensor
Sol. Solenoid
Sprchg. Supercharger
Strg. Steering
Susp. Suspension
Sw. Switch
Sys. System
\
\
\
\
\
\
\
\f
"T" ABBREVIATION TABLE
"T" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
T.V. Throttle Valve
TAB Thermactor Air By-Pass
TAC Thermostatic Air Cleaner
TAD Thermactor Air Diverter
TAN Tan
TBI Throttle Body Injection
Page 44 of 1501
* A/C-HEATER SYSTEM UNIFORM INSPECTION GUIDELINES *
1998 Mitsubishi Montero
GENERAL INFORMATION
A/C-Heater System Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
Motorist Assurance Program (MAP)
OVERVIEW
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Heating, Ventilation and Air Conditioning
ACCUMULATORS
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
AIR CONDITIONING FITTINGS
AIR CONDITIONING HOSES
AIR CONDITIONING METAL LINES, HOSES AND FITTING ASSEMBLIES
AIR CONTROL DOORS
AIR DAMS (EXTERNAL)
AIR DISTRIBUTION SYSTEM
BELTS
BLEND DOORS
BLOWER FANS (BLOWER WHEEL OR SQUIRREL CAGE)
BLOWER MOTORS
BLOWER RESISTORS
BLOWER SWITCHES
CABIN AIR FILTERS
CIRCUIT BREAKERS
COMPRESSOR CLUTCH ASSEMBLIES
COMPRESSORS
CONDENSER AIR SEALS
CONDENSER FAN MOTORS
CONDENSERS
CONNECTORS
CONTROL CABLES
CONTROL HEADS (FUNCTION SELECTORS)
CONTROL LINKAGES
CONTROL MODULES
COOLANT
COOLING FAN BLADES
COOLING FAN CLUTCHES
COOLING FAN MOTORS
EVAPORATOR DRAIN TUBES
EVAPORATOR PRESSURE REGULATORS (EPRS)
EVAPORATORS
EXPANSION VALVES
FUNCTION SELECTORS
FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS
FUSIBLE LINKS
GASKETS
HEATER CASES
HEATER CONTROL VALVES
HEATER CORES
Page 46 of 1501
are continually republished. In addition to these, standards for Drive
Train and Transmissions have recently been promulgated. Participating
shops utilize these Uniform Inspection & Communication Standards as
part of the inspection process and for communicating their findings to
their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
Page 53 of 1501
Worn so it contacts
bottom of pulley ....... A ............ Require replacement.
(1) - Determine cause of incorrect alignment and require repair.
( 2) - Determine cause of noise and suggest repair.
\
\
\
\
\
\
\
BLEND DOORS
See PLENUMS.
BLOWER FANS (BLOWER WHEEL OR SQUIRREL CAGE)
BLOWER FAN (BLOWER WHEEL OR SQUIRREL CAGE) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Application incorrect ... B .. Require repair or replacement.
Broken .................. A ............ Require replacement.
Cracked ................. A ............. Require replacement
Distorted ............... A ............ Require replacement.
Fins missing ............ C ............ Require replacement.
Hub separated ........... A ............ Require replacement.
Inoperative ............. A ........ ( 1) Require replacement.
Mounting loose .......... A .. Require repair or replacement.
Noisy ................... 2 ............ Suggest replacement.
Out of balance .......... A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
BLOWER MOTORS
BLOWER MOTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted,
affecting performance .. A ........... ( 1) Require repair or
replacement.
Connector melted, not
Page 104 of 1501
Other Means Of Identification
Refrigerant R-134a, when viewed through a sight glass, may
have a "milky" appearance due to the mixture of refrigerant and
lubricating oil. As the refrigerant and oil DO NOT exhibit a "clear"
sight glass on a properly charged A/C system, most R-134a systems have
no sight glass.
REFRIGERANT OILS
NOTE: Use ONLY the specified oil for the appropriate system or A/C
compressor. Always check vehicle underhood A/C specification
label or A/C compressor label before adding refrigerant oil
to A/C compressor/system. See Figs. 2 and 3. Always use
refrigerant oil specified on vehicle underhood A/C
specification label if different from the following list.
Refrigerant R-12 based systems use mineral oil, while R-134a
systems use Polyalkylene Glycol (PAG) oils. Using a mineral oil based
lubricant with R-134a will result in A/C compressor failure due to
lack of proper lubrication. The following R-134a refrigerant oils are
currently specified:
Use DENSO/ND-Oil 8 refrigerant oil on Nippondenso
compressors. Use SUN PAG 56 refrigerant oil on Sanden compressors.
NOTE: PAG oils absorb moisture very rapidly, 2.3-5.6 percent by
weight, as compared to a mineral oil absorption rate of
0.005 percent by weight.
SERVICE EQUIPMENT
A/C systems using R-134a refrigerant and PAG lubricants
cannot use R-12 refrigerant or mineral oil lubricants. R-134a
refrigerant is NOT compatible or interchangeable with R-12
refrigerant. Separate sets of hoses, manifold gauge sets and
recovery/recycling equipment are required to service the different
systems. This is necessary to avoid cross-contaminating and damaging
A/C system. A single set of A/C service equipment cannot be cleaned
thoroughly enough to be used with both types of refrigerant.
All equipment used to service A/C systems using R-134a must
be U.L. listed and certified to meet SAE standard J2210. The service
hoses on the manifold gauge set must have manual (turn wheel) or
automatic back-flow valves at the service port connector ends. This
will prevent refrigerant from being released into the atmosphere.
For identification purposes, R-134a service hoses must have a
Black stripe along its length and be clearly labeled SAE J2196/R-134a.
The low pressure test hose is Blue with a Black stripe. The high
pressure test hose is Red with a Black stripe, and the center test
hose is Yellow with a Black stripe.
R-134a manifold gauge sets can be identified by one or all of
the following: Labeled FOR USE WITH R-134a on set, labeled HFC-134a or
R-134a on gauge face, or by a Light Blue color on gauge face. In
addition, pressure/temperature scales on R-134a gauge sets are
different from R-12 manifold gauge sets.
SYSTEM SERVICE VALVES
SCHRADER-TYPE VALVES
NOTE: Although similar in construction and operation to a tire
valve, NEVER replace a Schrader-type valve with a tire valve.
Page 108 of 1501
When ignition switch is turned to ON or START position, SRS
warning light on instrument panel should come on for about 7 seconds
and then go off. This indicates SRS-ECU has determined SRS is
functioning properly. If SRS warning light flashes, stays on all the
time, or does not come on, a fault exists in SRS. See
DIAGNOSIS & TESTING.
FRONT IMPACT SENSORS
Sensors are inertia switches that verify direction and
severity of impact. If impact is great enough, switch contacts close,
completing an electrical circuit. Front impact sensors are located
under front fenders. See Fig. 1.
AIR BAG MODULE(S)
An inflator assembly in the air bag module produces nitrogen
gas to fill air bag. See Fig. 1. When a small amount of current from
SRS-ECU is applied, ignitor starts a thermal reaction, which spreads
to a pellet-filled canister that produces nitrogen gas. Gas pressure
builds and discharges from inflator through a diffuser and screen
assembly, forcing trim cover to burst along its seams until air bag is
fully inflated. When air bag is fully inflated, gas escapes through
vents on sides of air bag.
SRS AIR BAG CONTROL UNIT (ECU)
SRS-ECU (with integral safing and analog impact sensor) is
located behind front floor console assembly. See Fig. 1. If a system
fault occurs, SRS-ECU memory stores a diagnostic trouble code (DTC).
DATA LINK CONNECTOR (DLC)
DLC is located under left side of dash. See Fig. 1. DLC is
used to access SRS self-diagnostics through Mitsubishi Multi-Use
Tester II (MUT-II) (MB991502).
CLOCKSPRING
Clockspring connects driver-side air bag module to steering
column wiring, forming SRS circuit. See Fig. 1. Clockspring is a flat,
ribbon-like cable that winds and unwinds when steering wheel is
turned. Because of clockspring's constant movement, it is the most
fragile part in the system.
SYSTEM OPERATION CHECK
WARNING: After servicing, always turn ignition on from passenger-side
of vehicle in case of accidental air bag deployment.
Turn ignition switch to ON position. SRS warning light on
instrument panel should come on for about 7 seconds and then turn off.
This indicates SRS is functioning properly. If SRS warning light does
not come on, stays on, or comes on while driving, SRS is
malfunctioning and needs repair. See DIAGNOSIS & TESTING.
SERVICE PRECAUTIONS
Observe the following precautions when working with SRS:
* Disable SRS before servicing any SRS or steering column
Page 110 of 1501
Tool Name Tool Number
For Component Replacement
Steering Wheel Puller ......................... MB990803
For Testing SRS
Digital Volt-Ohm Meter (DVOM) ...................... (1)
Multi-Use Tester II ........................... MB991502
ROM Pack ........................................... ( 2)
SRS Check Harness ............................. MB991613
For Deploying Air Bags
SRS Air Bag Adapter Harness "A" ( 3) ........... MB686560
SRS Air Bag Adapter Harness "B" ( 4) ........... MB628919
( 1) - Maximum current output of DVOM must not exceed 2 mA
(milliamps) when set on minimum range of resistance
measurement.
( 2) - ROM pack is used with multi-use tester.
( 3) - For on-vehicle deployment of driver-side air bag. For
on-vehicle or off-vehicle deployment of passenger-side
air bag.
( 4) - For off-vehicle deployment of driver-side air bag.
\
\
\
\
\
\
DISABLING & ACTIVATING AIR BAG SYSTEM
WARNING: SRS system voltage is maintained for about 60 seconds after
battery cable is disconnected. After disconnecting battery
cable, wait at least 60 seconds before servicing SRS.
Failure to wait may cause accidental air bag deployment and
possible personal injury.
To disable system, turn ignition switch to LOCK position.
Disconnect negative battery cable. Shield cable end. Wait at least 60
seconds before servicing. To activate system, reconnect negative
battery cable.
DISPOSAL PROCEDURES
WARNING: Undeployed air bag must be deployed before disposal.
Disposing of an undeployed air bag may violate federal,
state and/or local laws. This also applies to vehicles that
are to be scrapped. Never sell a used air bag module.
UNDEPLOYED AIR BAG
WARNING: Deploy air bag outdoors and away from people. Air bag
deployment makes a loud noise. NEVER deploy air bag module
with trim cover face down.
NOTE: If replacing a deployed air bag, both front impact sensors
and SRS-ECU must also be replaced. If vehicle is to be
scrapped, perform PROCEDURE 1 (ON-VEHICLE DEPLOYMENT) below.
If vehicle will continue to be operated, perform PROCEDURE 2
(OFF-VEHICLE DEPLOYMENT) below.
Procedure 1 (On-Vehicle Deployment)
1) Before proceeding, follow air bag service precautions. See
SERVICE PRECAUTIONS . Open all doors and windows. Move vehicle to an
isolated area. Disconnect negative battery cable and wrap tape around
cable terminal.
2) Disconnect positive battery cable. Remove battery. Wait at
Page 112 of 1501
SERVICE PRECAUTIONS. Turn ignition switch to LOCK position. Disconnect
negative battery cable. Shield cable end. Disconnect positive battery
cable. Remove battery. Wait at least 60 seconds before continuing.
2) Remove air bag module. Place air bag module on ground at
least 20 feet away from people or objects. Air bag module face (trim
cover) must face upward to prevent movement of air bag module when it
is deployed.
3) Make a harness with two 20-foot (or longer) wires. Connec\
t
wires at one end of this harness to stripped wires of SRS Air Bag
Adapter Harness "B" (MB628919) for driver-side air bag, or SRS Air Bag\
Adapter Harness "A" (MB686560) for passenger-side air bag. See Fig. 2.
4) Wrap connections with insulating tape. Temporarily connect
other end of harness wires together to prevent unexpected air bag
deployment. Connect appropriate adapter harness to air bag module
connector. Place a tire without a rim over the air bag module so rim
hole surrounds air bag module. Stack 3 more tires on top of first
tire. Connect ends of 20-foot wires to terminals of a 12-volt battery.
5) After air bag module deploys, let it cool off and allow
dust to settle for at least 30 minutes before approaching. Tightly
seal deployed air bag module in a strong vinyl bag and dispose of air
bag as you would any other part.
DEPLOYED AIR BAG CLEAN-UP
WARNING: Vehicle interior will contain sodium hydroxide powder, a
by-product of air bag deployment. Since this powder can
irritate skin, eyes, nose and throat, wear safety glasses,
rubber gloves and long-sleeved shirt during clean-up.
1) Avoid breathing powder from air bag deployment. Begin
clean-up by putting tape over air bag exhaust vent to prevent
additional powder from escaping into vehicle interior. Use a vacuum
cleaner to remove any residual powder from A/C-heater outlets and
vehicle interior.
2) Turn blower motor to low for a few minutes and exit
vehicle. Turn blower motor off. Vacuum any other powder expelled from
plenum. Vacuum interior a second time to recover all powder. Avoid
kneeling or sitting on unclean areas. Wrap deployed air bag in heavy
vinyl plastic and dispose of it as you would any other part.
POST-COLLISION INSPECTION
When a vehicle has been involved in a collision, certain
components of the passive restraint system must be inspected or
replaced. See PASSIVE RESTRAINT SYSTEM INSPECTION article in the
GENERAL INFORMATION section for post-collision inspection information.
REMOVAL & INSTALLATION
WARNING: Follow air bag service precautions to prevent accidental air
bag deployment and personal injury. See SERVICE PRECAUTIONS.
Replace faulty SRS components; DO NOT repair or disassemble.
Handle all SRS components carefully.
DRIVER-SIDE AIR BAG MODULE & CLOCKSPRING
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Reactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Ensure front wheels are in straight-ahead position. Remove
lower covers from air bag module. Remove air bag module mounting nut
Page 113 of 1501
and screws. See Fig. 3. Lift air bag module for access to clockspring
connector at air bag module and disconnect clockspring connector. See
Fig. 4 . Remove air bag module.
3) Place air bag module on flat surface with trim cover
facing up. Remove steering wheel with Steering Wheel Puller
(MB990803). Remove lower column cover. Disconnect clockspring lower
connectors. Remove clockspring mounting screws. Remove clockspring.
See Fig. 3 .
Fig. 3: Removing Driver-Side Air Bag & Clockspring
Courtesy of Mitsubishi Motor Sales of America.
Fig. 4: Disconnecting Clockspring Connector From Air Bag Module
Courtesy of Mitsubishi Motor Sales of America.
WARNING: If front wheels are not in straight-ahead position or
clockspring mating marks are not aligned before installing