sensor MITSUBISHI MONTERO 2000 Service Owners Manual

MITSUBISHI MONTERO 2000 Service Owners Manual MONTERO 2000 MITSUBISHI MITSUBISHI https://www.carmanualsonline.info/img/19/57331/w960_57331-0.png MITSUBISHI MONTERO 2000 Service Owners Manual

Page 357 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-143
OK
Check the harness wire between the
intermediate connector and the
engine-A/T-ECU, and repair if
necessary.NG
Repair
NG
NG
Repair
NG
Repair
(2) NGMeasure at engine-

Page 358 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-144
Code No.24 Vehicle speed sensor systemProbable cause
Range of Check
DEngine: Two seconds after theengine wasstarted
DIdle switch: OFF
DEngine speed: 2,500 r/min or mo

Page 359 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-145
Code No.25 Barometric pressure sensor systemProbable cause
Range of Check
DTwo seconds have passed since the ignition switch is turned ON or the
engine startingproces

Page 360 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>GDI -Troubleshooting <A/T>13A-146
OK
Check the harness between the air
flow sensor and the engine-A/T-ECU,
and repair if necessary.
From the previouspage
OK
Measure at engine

Page 362 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-148
OK
Use an analyzer to measure the
signal waveform at engine-A/T-ECU
connectors D-119 and D-120.
DEngine: Idling
DSelector lever position: P
DVoltage between terminal

Page 363 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-149
OK
Check trouble symptom.
OK
Check trouble symptom.
OK
Check the following connectors:
B-101, B-108, B-112,
B-113, B-116, B-119
NG
Repair
OK
Replace the engine-A/T-EC

Page 365 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-151
Code No.56 Abnormal fuel pressureProbable cause
Range of Check
DIgnition switch: ON
Set Conditions
DThe sensor output voltage is 4.8V or more, or 0.2 V or less for fo

Page 366 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-152
NG
(2) NGCheck the following connector:
B - 111NG
Repair
OK
Measure at intermediate connector
B-110.
DUse test harness (MB991658) to
connect the connector, and
measur

Page 368 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-154
Code No.77 Accelerator pedal position sensor (2nd
channel) systemProbable cause
Range of Check
DAcceleratorpedal positionsensor (1st channel) is normal.
DCommunicatio

Page 369 of 1839

MITSUBISHI MONTERO 2000  Service Owners Manual GDI -Troubleshooting <A/T>13A-155
OK
Measure at throttle valve controller
connector D-11.
DMeasure voltage at the throttle
valve controller connector
terminals.
DIgnition switch: ON
DThe resistance be