stop start MITSUBISHI MONTERO 2000 Service User Guide

GDI -Troubleshooting 13A-205
Terminal
No.Normal condition Check condition (Engine condition) Check item
18Condenser fan relayCondenser fan not operatingSystem voltage
Condenser fan operating0 - 3 V or more
19Air flow sensor resetEngine: Idling0-1V
signal
Engine speed: 3,000 r/min6-9V
20A/C relayDEngine: Idling
DA/C switch: OFF to ON (Compressor operating)System voltage or
changes momentarily 6
V or more to 0 - 3 V
21Fuel pump relayIgnition switch: ONSystem voltage
Engine: Idling0-3V
22Engine warning lampIgnition switch: OFF to ONSystem voltage
23GDI ECO indication
lampIgnition switch: OFF to ON0 - 3 V (system voltage
after five seconds)
Rev the engine suddenly.System voltage
34Purge control solenoidDEngine coolantEngine: stoppedSystem voltage
valvetemperature: 80 -
95_C
DIgnition switch:
ON
Engine: After starting, in-
crease the engine speed
up to 3,500 r/minThe voltage drops
41Power supplyIgnition switch: ONSystem voltage
47
43Engine ignition signalEngine speed: 3,000 r/min0.3 - 3.0 V
44Engine coolant tem-
perature sensorIgnition switch: ONWhen engine coolant tem-
perature is 0_C3.2 - 3.8 V
When engine coolant tem-
perature is 20_C2.3 - 2.9 V
When engine coolant tem-
perature is 40_C1.3 - 1.9 V
When engine coolant tem-
perature is 80_C0.3 - 0.9 V
45Crank angle sensorEngine: Cranking0.4 - 4.0 V
Engine: Idling1.5 - 2.5 V
46Power supply voltage
applied to accelerator
pedal position sensor
(1st channel)Ignition switch: ON4.5 - 5.5 V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting13A-6
Item
No.Refer-
ence
page Inspec-
tion pro-
cedure
No. Normal condition Inspection contents Inspection
item
81LLearned
valueEngine: Warm, 2,500 r/min without any load
(during closed loop lambda control)- 10 - 10 %Code
No.
P017013A-34*
82LClosed loop
controlEngine: Warm, 2,500 r/min without any load
(during closed loop lambda control)- 25 - 25 %Code
No.
P017013A-34*
87LEngine loadEngine: After having
warmed upIdling (more than 4
minutes later after
the engine has
started)20 - 40 %--
2,500 r/min10 - 30 %
8ALThrottle
position
sensor(1st
DEngine: After hav-
ing warmed up
DIgnitionswitch:ON
Release the
accelerator pedal.0 - 20 %Code
No.
P0120
13A-25*
sensor(1st
channel)
(throttle
valve angle)DIgnition switch:ON
(Engine: stopped)Depress the
accelerator pedal.Increase in
proportion to the
pedal strokeP0120
Depress the
accelerator pedal
fully.80 - 100 %
NOTE
L: will not displayed if service data is selected on the check mode.
*: Refer to the 2001 PAJERO Workshop Manual (Pub.No. PWJE0001)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

DIESEL FUEL <4M4> -General/Service Specifications/Troubleshooting13C-2
GENERAL
OUTLINE OF CHANGES
Some service procedures have been established as the following changes have been made due to the
compliance with the Emission Regulation StepIII.
DThe intake manifold cover and injection pump cover have been reshaped.
DThe throttle body assembly has been changed.
DThe EGR valve assembly has been changed.
SERVICE SPECIFICATIONS
ItemStandard value
Throttle body assembly resistanceΩat - 10 - 50_C12 - 20
at 50 - 100_C12 - 23
TROUBLESHOOTING
FAIL-SAFE, BACKUP FUNCTIONS
When abnormalities in the major sensors are detected by diagnosis functions, pre-set control logic operates
to maintain a safe driving condition for the vehicle.
Diagnosis itemControl features in malfunction
Accelerator pedal position sensorDAccelerator pedal released (idle switch ON)
Acceleration opening degree = 0 %
DAccelerator pedal applied (idle switch OFF)
Engine controlled at low speed
Acceleration opening degree = 40 % , 28 %
DVoid cruise control
Idle switchDVoid idling speed control
DVoid cruise control
Engine speed sensorDEngine controlled at low speed
DVoid cruise control
Boost air temperature sensorMaintain the intake air temperature at 50_C
Vehicle speed sensorDVoid idling speed control
DVoid cruise control
DWith accelerator pedal released (when idle switch is on)
Accelerator opening angle = 0 %
DWith accelerator pedal depressed (when idle switch is off)
Accelerator opening angle = Fixed at 40 % (M/T), 28 % (A/T)
Engine coolant temperature sensorMaintain the engine coolant temperature at 80_C (engine running), 0_C
(engine stopped or just started)
Control sleeve position sensorDWith accelerator pedal released (when idle switch is on)
Engine speed = 800 r/min
DWith accelerator pedal depressed (when idle switch is off)
Engine speed = 2,000 r/min
DVoid cruise control
Timer piston position sensorDOpen control by means of engine speed
DVoid cruise control
Barometric pressure sensor (ECU built-in)Keep the barometric pressure at 101 kPa


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

MITSUBISHI SC-Troubleshooting13E-12
INSPECTION CHART FOR TROUBLE SYMPTOMS
Trouble SymptomInspection
procedure
No.Reference
page
Communication with MUT-II is not possible.113E-12
Communication with MUT-II and the SC-ECU is not possible.213E-13
The SC warning lamp does not illuminate when the ignition key is turned to ON (engine
stopped).313E-14
The SC warning lamp remains illuminated after the engine has started.413E-14
INSPECTION PROCEDURES FOR TROUBLE SYMPTOMS
Inspection procedure 1
Communication with MUT-
IIis not possible.
Probable cause
The cause is probably a malfunction of the diagnosis connector power supply
circuit or earth circuit.DMalfunction of diagnosis connector
DMalfunction of harness or connector
NGCheck the following connectors:
D-27, D-211, D-210, D-23
NG
Repair
OK
Check the trouble symptoms.
NG
Check the harness wire between battery and diagnosis
connector, and repair if necessary.
OK
NG
NG
Repair
OK
Check the trouble symptoms.
NG
Check the harness wire between diagnosis connector and
earth, and repair if necessary.
OK
NG
Replace the MUT-
II.
Measure at diagnosis connecter D-23.
DVoltage between 16 and body earth
OK:
System voltage
Check the following connector:
D-23Measure at diagnosis connecter D-23.
DContinuity between terminals 4, 5 and body earth
OK:
Continuity
Check the trouble symptoms.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

MITSUBISHI SC-Troubleshooting13E-14
Inspection procedure 3
The SC warning lamp does not illuminate when the
ignition key is turned to ON (engine stopped).
Probable cause
When the ignition switch is turned on, the SC-ECU starts to communicate with
the engine-ECU or engine-A/T-ECU. Then the SC-ECU will illuminate the SC
warning lamp if the engine speed is 350 rpm or less. If the SC warning lamp
does not illuminate, the case is probably an open circuit in the SC warning lamp
power supply circuit, a blow lamp bulb or an open circuit between the SC
warning lamp and the SC-ECU.DBlown fuse
DBlown SC warning lamp bulb
DMalfunction of harness or connector
DMalfunction of combination meter
DMalfunction of the SC-ECU
NG
Replace the combination meter.
NG
Repair
OK
NG
Check for a blown bulb.Replace the SC
warning lamp bulb.
OK
NG
Repair
OK
Check the trouble symptoms.
Multi - purpose fuse No. 6 checkNGRefer to Basic Manual GROUP 00 – Inspection service Points
for Blown Fuse.
NG
Check the harness wire.
DBetween the ignition switch and the combination meter
DBetween the combination meter and the SC-ECU
OK
OK
Replace the SC-ECU
Check the following connector:
E-107
NG
RepairCheck the trouble symptoms.OK
NG
Check the following connectors:
D-208, D-210 ,
D-213 , D-01, E-10, E-122, E-120
Measure at the SC-ECU connector E-120.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DWarning lamp condition when terminal 45 is shorted to
body earth
OK:
Illuminates
Inspection procedure 4
The SC warning lamp remains illuminated after the
engine has started.
Probable cause
The cause is probably a short-circuit in the SC warning lamp illumination circuit.DMalfunction of combination meter
DMalfunction of harness (short-circuit)
DMalfunction of the SC-ECU
NOTE
This trouble symptom is limited to cases where communication with the MUT-II is possible(SC-ECU power
supply is normal) and the diagnosis code is a normal diagnosis code.
When the SC-ECU connector E-120 are disconnected and the
ignition switch is turned to the ON position, does the SC
warning lamp remain illuminated?YES
NO
Replace the SC-ECU.Replace the combination meter.
NG
Repair
OK
Check the harness wire between the combination meter and
the SC-ECU


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-6
No.Inspection pro-
cedure if there is
an abnormality Diag-
nosis
code
No. Check item Judgment value Test/operation Pre-test/opera-
tion conditions
3Ignition switch:
START
Engine: StoppedStarting test at P or N
positionStarting should be
possibleStarting pos-
sible/not
possible-Starting not
possible
4Driving after en-
gine has warmed
upDrive for 15 minutes
or more until the A/T
fluid temperature
rises to 70 - 80_
C.Data list No.15
Gradually rises to 70
-80_
CA/T fluid tem-
perature
sensor15A/T fluid temper-
ature sensor sys-
tem
5Engine: Idling
Selector lever
position: NBrake pedal (re-test)
(1) Depressed
(2) ReleasedData List No. 26
(1) ON
(2) OFFStop lamp
switch26Stop lamp switch
system
A/C switch
(1) ON
(2) OFFData List No. 65
(1) ON
(2) OFFDual pres-
sure switch-Dual pressure
switch system
Accelerator pedal
(1) Fully closed
(2) ApplyData List No. 21
(1) The engine
speed displayed
on the tachome-
ter is identical to
the engine
speed displayed
on MUT-II.
(2) Gradually in-
creases from (1)Crank angle
sensor
<6G7>
Engine
speed sen-
sor
<4M4>21Crank angle sen-
sor system
<6G7>
Engine speed
sensor system
<4M4>
Data List
No.73 <6G7>
No.76 <4M4>
(2) Data changes.Communica-
tion with en-
gine-ECU51Serial commu-
nication system
Selector lever posi-
tionNo abnormal shock
during shiftingMalfunction
when start--Engine stalls dur-
ing shifting
(1) N to D
(2) N to RWithin 2 seconds of
time laging off-N-to-D shocks,
large time lag
-N-to-R shocks,
large time lag
-N-to-D, N-to-R
shocks, large
time lag
Driving not
possible-Does not move
forward
-Does not reverse
-Does not move
(forward or re-
verse)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-68
Ter-
minal
No.Standard value Inspection conditions Check item
54Input communication withEngine: IdlingOther than 0 V
engine-ECUSelector lever position: D
55Inhibitor switch PIgnition switch: ON
Selector lever position: PSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
56Inhibitor switch NIgnition switch: ON
Selector lever position: NSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
57Select switchIgnition switch: ON
Selector lever operation: Sports modeSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
58Downshift switchIgnition switch: ON
Selector lever position: Downshifted in Sports mode
and lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
59Stop lamp switchIgnition switch: ON
Brake pedal DepressedSystem voltage
Ignition switch: ON
Brake pedal Released0V
62DIR solenoid valveEngine: Idling
Shift range: ParkSystem voltage
Engine: Idling
Shift range: 2nd7-9V
65Wide open throttle switchAccelerator pedal: Released4.5 - 5.5 V
Accelerator pedal: DepressedLess than 0.4 V
66Inhibitor switch RIgnition switch: ON
Selector lever position: RSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
67Inhibitor switch DIgnition switch: ON
Selector lever position: DSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
68Upshift switchIgnition switch: ON
Selector lever position: Upshifted in Sports mode and
lever heldSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
69Vehicle speed sensorWhen stopped0V
When starting to drive forward slowly.0 V and 5 V alter-
nates
71A/T control relayIgnition switch: OFF0V
Ignition switch: ON10 - 12 V
72EarthIgnition switch: ON0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

BASIC BRAKE SYSTEM -Troubleshooting35A-13
Code No.79 Pressure switch system (open or short
circuit)Probable cause
This code is output if the pressure switch circuit is short, ABS-ECU internal circuit
is defective, or the hydraulic brake booster (HBB) pressure switch or master cylinder
and hydraulic unit assembly is defective.DMalfunction of connector or harness
DMalfunction of the ABS-ECU
DMalfunction of the HBB (pressure switch or master
cylinder and hydraulic unit assembly)
NG
Repair
NG
OKRepair NG
OK
Check trouble symptom.
Check the following connectors:
B-17, B-18, E-106, E-107
Check the harness wire:
DBetween the HBB and the ABS-ECU
DBetween the HBB and the earthNG
Check trouble symptom.
Replace the ABS-ECU. (Refer to GROUP 35B.)
NG
OKCheck the pressure switch. (Refer to P.35A-23.)Replace the master cylinder and hydraulic unit assembly.
INSPECTION CHART FOR TROUBLE SYMPTOMS
Trouble symptomInspection
procedure
No.Reference page
The brake warning lamp does not illuminate when the ignition switch is turned ON
(engine stopped).135A-14
The brake warning lamp remains illuminated after the engine is started.235A-15
The HBB buzzer does not sound when the hydraulic brake booster (HBB) is
defective. (However, the brake warning lamp is illuminated.)335A-15
The HBB buzzer does not stop sounding.435A-16
Communication with MUT-II
is not possible.Refer to GROUP 35B.
Communication with MUT-II
and the ABS-ECU is not possible.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ABS <4WD> -Troubleshooting35B-18
INSPECTION CHART FOR TROUBLE SYMPTOMS
Trouble SymptomInspection
procedure
No.Reference
page
Communication with MUT-II is not possible.135B-18
Communication with MUT-II and the ABS-ECU is not possible.235B-19
The ABS warning lamp does not illuminate when the ignition key is turned to ON (engine
stopped).335B-20
The ABS warning lamp remains illuminated after the engine has started.435B-20
The brake warning lamp does not illuminate when the ignition switch is turned ON (engine
stopped).Refer to GROUP 35A.
The brake warning lamp remains illuminated after the engine has started.
Abnormal brake operation535B-21
Caution
(1) Because the ABS may also operate at times when sudden braking is not being carried out,
such as when driving on low frictional coefficient roads, when turning at high speed or during
high - speed overtaking, check with the customer that the problems are not occurring when
driving under conditions such as these.
(2) When the ABS is operating, changes in the brake pedal feel (vibration and difficulty depressing
the pedal) may occur. This happens because the hydraulic pressure inside the brake line is
continually changing in order to stop the wheels from locking up, and is not a malfunction.
INSPECTION PROCEDURES FOR TROUBLE SYMPTOMS
Inspection procedure 1
Communication with MUT-II
is not possible.
Probable cause
The cause is probably a malfunction of the diagnosis connector power supply
circuit or earth circuit.DMalfunction of diagnosis connector
DMalfunction of harness or connector
NGCheck the following connectors:D-23, D-27, D-210, D-211
NG
Repair
OK
Check the trouble symptoms.
NG
Check the harness wire, and repair if necessary.
DBetween battery and diagnosis connector
OK
NG
NG
Repair
OK
Check the trouble symptoms.
NG
Check the harness wire, and repair if necessary.
DBetween diagnosis connector and earth
OK
NG
Replace the MUT-
II.
Measure at diagnosis connecter D-23.
DVoltage between 16 and body earth
OK:System voltage
Check the following connector:D-23
Measure at diagnosis connecter D-23.
DContinuity between terminals 4, 5 and body earth
OK:Continuity
Check the trouble symptoms.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ABS <4WD> -Troubleshooting35B-20
Inspection procedure 3
The ABS warning lamp does not illuminate when the
ignition key is turned to ON (engine stopped).
Probable cause
When power is first supplied to the ABS-ECU, the ABS-ECU turns the ABS-ECU
valve relay from off to on, off and back to onagain aspart of its initial check.
Accordingly, if the ABS warninglampdoes not illuminate, the cause is probably
an opencircuit in the ABS warninglamppower supply circuit, a blownlamp bulb
or an opencircuit between the ABS warninglamp and theABS-ECU.DBlown fuse
DBlown ABS warninglamp bulb
DMalfunction of ABS valve relay
DMalfunction of harness or connector
DMalfunction of combination meter
DMalfunction of the ABS-ECU
NG
Replace the combination meter.
NG
Repair
OK
NG
Check for a blown bulb.Replace the ABS
warning lamp bulb.
OK
NG
Repair
OK
Check the trouble symptoms.
Multi - purpose fuse No. 6 checkNGRefer to GROUP 00 – Inspection service Points for Blown
Fuse.
NG
Check the harness wire.
DBetween ignition switch and combination meter
DBetween the combination meter and the ABS-ECU
OK
OK
After replacing the ABS-ECU, carry out the following check.
DCheck the harness wire between the ABS warning lamp,
ABS valve relay and earth.
Check the following connector:E-107
NG
RepairCheck the trouble symptoms.OK
NG
Check the following connectors:D-01, D-208, D-210
, D-213 , E-10, E-107
Measure at the ABS-ECU connector E-107.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DWarning lamp conditionwhen terminal 50 is shorted to
body earth
OK:Illuminates
Inspection procedure 4
The ABS warning lamp remains illuminated after the
engine has started.
Probable cause
The cause is probably a short-circuit in the ABS warninglamp illuminationcircuit.DMalfunction of combination meter
DMalfunction of harness (short-circuit)
DMalfunction of the ABS-ECU
NOTE
This trouble symptom is limited to cases where communication with the MUT-II is possible(ABS-ECU
power supply is normal) and the diagnosis code is a normal diagnosis code.
When the ABS valve relay connector B-21X and the
ABS-ECU connector E-107 are disconnected and the ignition
switch is turned to the ON position, does the ABS warning
lamp remain illuminated?YES
NO
Replace the ABS-ECU.
Replace the combination meter.
NG
Repair
OK
Check the harness wire.
DBetween the ABS warning lamp, the ABS-ECU and the
ABS valve relay


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk