catalytic converter MITSUBISHI MONTERO 2000 Service Repair Manual

GDI -Troubleshooting 13A-61
Code No.P0420 Catalyst malfunctionProbable cause
Range of Check
DThe enginespeed is 3,000 r/min or less.
DDuring driving
DDuring air/fuel ratio feedback control
Set Conditions
DThe ratio between the oxygen sensor (rear) and the oxygen sensor (front)
output frequencies reaches 0.8 per 12 seconds on average.DMalfunction of catalyst
DMalfunction of the oxygen sensor (front)
DMalfunction of the oxygen sensor (rear)
DMalfunction of engine-ECU
Check the trouble symptoms.
Check the exhaust manifold. (Are there anycracks?)NG
OK
MUT-
IIData list
59 Oxygen sensor (rear)
DTransmission: 2nd
DDrive with wideopen throttle
OK:
600 - 1,000 mVNGCheck the oxygen sensor (rear) system
(Refer to P.13A-31, INSPECTIONPROCEDURE FOR
DIAGNOSTIC TROUBLE CODE P0136.)
OK
MUT-
IIData list
11 Oxygen sensor (front)
DTransmission: 2nd
OK:
Changeover between 0 - 400 mV and 600 - 1,000
mV occur 15 times in 10 seconds.
OK
Replace the oxygen sensor (rear).
NG
Replace the catalytic converter.
Check the trouble symptoms.
NG
Replace the engine-ECU.
MUT-
IIData list
11 Oxygen sensor (front)
OK:
600 - 1,000 mV when racing suddenly
OK
NGRepair
Check the oxygen sensor (front) system
(Refer to P.13A-28, INSPECTIONPROCEDURE FOR
DIAGNOSTIC TROUBLE CODE P0130.)
Replace the oxygen sensor (front). NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-93
From the previouspage
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-105.)NGCheck the EGR valve system. (Refer to P.13A-60, code No. P0403.)
OK
MUT-
IIActuator test
08 Purge control solenoid valve (Refer to P.13A-110.)NGCheck purge control solenoid valve system. (Refer to P.13A-62,
code No. P0443.)
OK
Check trouble symptom.NGReplace the injector.
Check trouble symptom.
NG
Replace the three-way catalytic converter.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-186
Check the trouble symptoms.NG
From the previouspage
Check the trouble symptoms.
Replace the catalytic converter.
OK
Check the following items in that order.
DCheck the sparkplug
DCheck the compression pressure
DCheck the positive crankcase ventilation system.
NG
Replace the injector.
Inspection procedure 19
Low alternator output voltage (approx.12.3 V)
Probable cause
The cause is probably a malfunction of the alternator or one of the problems
listed at right.DMalfunction of the charging system
DOpen circuit between the alternator G terminal and
the engine-A/T-ECU
DMalfunction of the engine-A/T-ECU
Measure at alternator connector B-59
DConnect the connector.
(Use test harness: MB991519)
DThe voltage between terminal 1
(black clip) and earth
(Engine: Idling)
(Headlamp: OFF to ON)
(Stoplamp: OFF to ON)
(Rear defogger switch: OFF to
ON)
OK:
The voltage increases by
0.2 - 3.5 VNGMeasure at alternator connector B-59
DDisconnect the connector, and
measure at the harness side.
DDisconnect the engine-A/T-ECU
connector
DThe continuity between terminal 1
and earth
OK:
No continuityNGCheck the harness wire between the
alternator and the engine-A/T-ECU,
and repair if necessary.
OK
Check the alternator
(Refer to GROUP16 - Charging
System.)NG
OK
Check the following connectors:
B-41, D-119Repair
OK
Replace the engine-A/T-ECU.
OK
Check the trouble symptoms.
NG
NG
Check the harness wire between the
alternator and the engine-A/T-ECU.Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

15
DRIVE CYCLE
Performing the running test of the car using the following five drive cycle patterns makes it possible to
monitor all the diagnosis codes that are required for operation of the car in order to determine if the
applicable system is operating properly or not.
In other words, doing such a drive allows to regenerate any kind of trouble which involves illuminating the
Engine Warning Lamp (Check Engine Lamp) and to verify the repair procedure has eliminated the trouble
[the Engine Warning Lamp (Check Engine Lamp) is no longer illuminated].
Caution
Two technicians should always be in the vehicle when carrying out a test drive.
NOTE
Check that the diagnosis code is not output before traveling in the Drive cycle pattern. Erase the diagnosis
code if it has been output.
DRIVE CYCLE PATTERN LIST
PROCEDURE MONITOR ITEM DIAGNOSIS CODE
Catalytic converter monitor P04201
Heated oxygen sensor monitor P0130
2 Fuel trim monitor P0170
3 Feed back monitor P0125
4 Other monitor P0136, P0201, P0202, P0203, P0204, P0205,
P0206, P0300, P0301, P0302, P0303, P0304,
P0305, P0306, P0325
NOTE
The vehicle speed sensor (P0500) and the power steering fluid pressure switch (P0551) are used to
determine if the system is operating properly or not through use of the Data List function of the MUT-II.
2001 PAJERO/MONTERO WAGON Workshop Manual 6G74
GDI - Troubleshooting

www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

INTAKE AND EXHAUST -Exhaust Pipe and Main Muffler<4M4>15-26
Exhaust main muffler and rear
floor heat protector removal steps

1. Exhaust main muffler
6. Hanger
7. Hanger bracket
8. Hanger bracket
11. Rear floor heat protector
Tail exhaust pipe and rear floor
heat protector removal steps

2. Tail exhaust pipe
7. Hanger
9. Hanger bracket
10. Hanger bracket
12. Rear floor heat protector
Center exhaust pipe removal steps

3. Center exhaust pipe
13. Hanger
14. Hanger bracketExhaust main muffler removal steps

4. Exhaust main muffler
13. Hanger
14. Hanger bracket
Front exhaust pipe and dash heat
protector removal steps
DUnder cover
5. Front exhaust pipe
15. Exhaust support bracket
16. Dash heat protector
Front floor heat protector removal
steps
17. Catalytic converter
18. Front floor heat protector
19. Seal ring


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

INTAKE AND EXHAUST -Exhaust Pipe and Main Muffler <4D5>15-15
Exhaust main muffler and rear
floor heat protector removal steps

1. Exhaust main muffler
6. Hanger
7. Hanger bracket
8. Hanger bracket
11. Rear floor heat protector
Tail exhaust pipe and rear floor
heat protector removal steps

2. Tail exhaust pipe
6. Hanger
9. Hanger bracket
10. Hanger bracket
12. Rear floor heat protector
Center exhaust pipe removal steps

3. Center exhaust pipe
13. Hanger
14. Hanger bracketExhaust main muffler removal steps

4. Exhaust main muffler
13. Hanger
14. Hanger bracket
Front exhaust pipe and dash heat
protector removal steps
DUnder cover
5. Front exhaust pipe
15. Exhaust support bracket
16. Dash heat protector
Front floor heat protector removal
steps
17. Catalytic converter
18. Front floor heat protector
19. Seal ring


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

17-2
EVAPORATIVE EMISSION CONTROL
SYSTEM 36..............................
General Information 36......................
System Diagram 36.........................
Component Location 36......................
Purge Control System Check 37..............
Purge Port Vacuum Check 37................
Purge Control Solenoid Valve Check 38.......
EXHAUST GAS RECIRCULATION (EGR)
SYSTEM 39..............................
General Information 39......................
Operation 39................................
System Diagram 39.........................
Component Location 39......................
Exhaust Gas Recirculation (EGR) Control
System Check 40...........................
EGR Valve (Stepper Motor) Check 40........
EGR VALVE 42...........................
CANISTER 43............................
CATALYTIC CONVERTER 44..............
General Information 44......................
EMISSION CONTROL SYSTEM
<4D5> 45.............................
GENERAL INFORMATION 45..............
SERVICE SPECIFICATIONS 45............
SEALANT 45.............................
SPECIAL TOOL 45.......................
EXHAUST GAS RECIRCULATION (EGR)
SYSTEM 46..............................
General Information 46......................
System Diagram 46.........................
Component Location 46......................
Function Check 47..........................
EGR Solenoid Valve Operation Check 47.....
EGR Solenoid Valve Resistance Check 48....
Lever Position Sensor (LPS) Adjustment 48...
Engine Speed Sensor Check 49..............
Engine Coolant Temperature Sensor
Check 49...................................
CHECK AT THE GLOW & EGR CONTROL
UNIT 51..................................
EMISSION CONTROL SYSTEM
<4M4-VEHICLES WITH EGR> 52........
GENERAL INFORMATION 52..............
SERVICE SPECIFICATIONS 52............
EXHAUST GAS RECIRCULATION (EGR)
SYSTEM 53..............................
General Information 53......................
System Diagram 53.........................
Component Location 53......................
Function Check 54..........................
EGR Solenoid Valve Operation Check 54.....
EGR Solenoid Valve Resistance Check 55....
Accelerator Pedal Position Sensor (APS),
Engine Coolant Temperature Sensor, Intake
Air Temperature Sensor, Fuel Temperature
Sensor Check 55............................
Check at Engine-ECU 55....................
CATALYTIC CONVERTER 55..............
General Information 55......................


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ENGINE AND EMISSION CONTROL -Emission Control System <6G7>17-31
EMISSION CONTROL SYSTEM <6G7>
GENERAL INFORMATION
The emission control system consists of the following subsystems:
DCrankcase emission control system
DEvaporative emission control system
DExhaust emission control system
ItemsNameSpecification
Crankcase emission
control systemPositive crankcase ventilation (PCV) valveVariable flow type
(Purpose: HC reduction)
Evaporative emission
control systemCanister
Purge control solenoid valveEquipped
Duty cycle type solenoid valve
(Purpose: HC reduction)
Exhaust emission
control systemAir-fuel ratio control device - GDI systemOxygen sensor feedback type
(Purpose: CO, HC, NOx reduction)
Exhaust gas recirculation system
DEGR valveEquipped
Stepper motor type
(Purpose: NOx reduction)
Catalytic converterMonolith type
(Purpose: CO, HC, NOx reduction)
EMISSION CONTROL DEVICE REFERENCE TABLE
Related partsCrankcase
emission
control
systemEvaporative
emission
control
systemAir/fuel
ratio
control
systemCatalytic
converterExhaust
gas
recirculation
systemReference
page
PCV valve´17-35
Purge control solenoid valve´17-38
GDI system component´´GROUP
13A
Catalytic converter´17-44
EGR valve´17-40


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

17-1
ENGINE AND
EMISSION
CONTROL
CONTENTS
ENGINE CONTROL SYSTEM 2........
GENERAL 2...............................
Outline of Change 2.........................
EMISSION CONTROL SYSTEM
<4D5-STEPIII>
2 .....................................
GENERAL 2...............................
Outline of Changes 2........................
GENERAL INFORMATION 2................
SERVICE SPECIFICATIONS 2..............
EXHAUST GAS RECIRCULATION (EGR)
SYSTEM 3................................EGR VALVE AND EGR COOLER 6.........
CATALYTIC CONVERTER 8................
EMISSION CONTROL SYSTEM <4M4>
9 .....................................
GENERAL 9...............................
Outline of Change 9.........................
SERVICE SPECIFICATIONS 9..............
EXHAUST GAS RECIRCULATION (EGR)
SYSTEM 9................................
EGR VALVE AND EGR COOLER 11........


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ENGINE AND EMISSION CONTROL -EngineControlSystem/EmissionControl
System <4D5-Step III>17-2
ENGINE CONTROL SYSTEM
GENERAL
OUTLINE OF CHANGE
Electronic-controlled throttle valve system has been used instead of a conventional cable-type accelerator
mechanism <4D5>.
Its service procedure is the same as for previous models with 6G7 or 4M4 engine.
EMISSION CONTROL SYSTEM <4D5-STEP
III>
GENERAL
OUTLINE OF CHANGES
Some service procedures have been established as the following changes have been made due to the
compliance with the Emission Regulation Step III.
DAn electronic-controlled EGR valve and EGR cooler have been used.
DA catalytic converter has been added.
GENERAL INFORMATION
The electronically-controlled EGR system reduces
the level of exhaust gases (NO
x).
ItemsNameSpecification
Exhaust emission
control systemExhaust gas recirculation system
DEGR valve
DEGR solenoid valve No.1
DEGR solenoid valve No.2
DEGR valve position sensorElectronically-controlled EGR system
Single type
ON-OFF solenoid valve
ON-OFF solenoid valve
Variable resistor type
SERVICE SPECIFICATIONS
ItemsStandard value
EGR solenoid valve Nos. 1 and 2 resistance (at 20_C)Ω36 - 44


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk