time MITSUBISHI OUTLANDER 2018 Owner's Manual (in English)

Replacement of light bulbs
Vehicle care and maintenance 9-31
9
4. Use the fuse location diagrams and thematching tables, to check the fuse that isrelated to the problem. If the fuse is notblown, something else must be causingthe problem. Have the system inspectedby your authorized Mitsubishi Motorsdealer or a repair facility of your choice.
5. Insert a new fuse
of the same capacity
securely into the appropriate slot.
N00942901391
Before replacing the bulb, be sure the light isoff. Do not touch the glass part of the newbulb with your bare fingers; the oil from yourskin will stay on the glass and dim or destroythe bulb when it gets hot.
B- Fuse is OKC- Blown fuse
CAUTIONNever use a fuse with a capacity greater thanthe one listed or any s
ubstitute, such as wire,
foil etc. This would
cause the circuit wiring
to heat up and could cause a fire.If the replacement fuse blows again after ashort time, have the electrical systemchecked by an authorized Mitsubishi Motorsdealer or a repair faci
lity of your choice to
find and correct
the cause.
Replacement of light bulbs
CAUTIONBulbs are extremely hot immediately afterbeing turned off.When replacing the bulb, wait for it to coolsufficiently before
touching it. You could
otherwise be burned.
Handle halogen light bul
b with care. The gas
inside a halogen light
bulb is highly pressur-
ized, so dropping, knocki
ng, or scratching a
halogen light bulb can
cause it to shatter.
Never hold the halogen
light bulb with a bare
hand, dirty glove, etc.The oil from your hand could cause the bulbto break the next time the headlights areused.If the glass surface is dirty, clean it withalcohol and let it dry completely beforeinstalling the bulb.CAUTIONDo not install commercially available LED-type bulbs. Commercia
lly available LED-
type bulbs could adversely affect the opera-tion of the vehicle, such as by preventing thelights and other vehicle equipment fromoperating properly.CAUTION
BK0249100US.book 31 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs9-32 Vehicle care and maintenance
9
N00943000132
The bulb should only be replaced with a newbulb with the same rating and type. The typeand rating are listed on the base of the bulb.
N00950302072
NOTE
If you are unsure of how to carry out thework as required, it is recommended thatthese procedures be ca
rried out by an autho-
rized Mitsubishi Motors
dealer or a repair
facility of your choice.Be careful not to scratch the vehicle bodywhen removing a light and lens.When it rains, or wh
en the vehicle has been
washed, the inside of the lens sometimesbecomes temporarily foggy. This is the samephenomenon as when window glass mists upon a humid day, and does not indicate a func-tional problem.When the light is switched on, the heat willremove the fog. However, if water gathersinside the light, please
have it checked by an
authorized Mitsubishi Motors dealer or arepair facility of your choice.
Bulb capacity
Outside Type A: Halogen headlights typeType B: LED headlights typeFrontTy p e ATy p e B
Item
Wa t t-age
ANSI Tr a d e No. or Bulb type
1 - Front turn signal light 21 W PY21W2 - Headlight, high beam 60 W
9005 HB3
3 -
Head-light, low beam
Halogen bulb
55 W H7
LED — —
Daytime running light
——
5 - Front side-marker
light
5 W W5W
6-
Front fog light (if so equipped)
Halogen bulb
19 W H16
LED — —
(if so equipped)
The following lights use an LED instead ofthe bulb.Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when either light need
s to be repaired or
replaced.
BK0249100US.book 32 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs
Vehicle care and maintenance 9-33
9
N00950401731
• Headlight, low be
am (LED type)
• Parking light• Daytime running light• Front fog light (LED type)• Side turn signal light
Item
Wattage
ANSI trade No. or Bulb type
1 - High-mounted
stop light
——
2 - Tail light — —
marker light
——
4 - License plate
light
5 W W5W
5 - Back-up light 16 W W16W
NOTE
Rear
6 - Rear turn sig-
nal light
21 W WY21W
7 - Stop light — —The following lights use an LED instead ofthe bulb. Check with an authorized Mitsubi-shi Motors dealer or a
repair facility of your
choice when either light
needs to be repaired
or replaced.• Rear side-marker light• High-mounted stop light• Tail light• Stop light
Item
Wattage
ANSI trade No. or Bulb type
Inside
Item
Wattage
1 - Cargo room light 8 W2 - Dome light (rear) 8 W3 -
Dome light (front)/Read-ing light
8 W
4 - Downlight –6 - Glove compartment light 1.4 W
NOTE
The following lights us
e an LED instead of
the bulb. Check with an authorized Mitsubi-shi Motors dealer or a repair facility of yourchoice when the light needs to be repaired orreplaced.• Downlight
BK0249100US.book 33 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs9-36 Vehicle care and maintenance
9
N00917301724N00943401423
1. Remove the 12 clips (A, B), and thenremove the cover (C).
2. Turn the socket (D
) counterclockwise to
remove it, then remove the bulb from thesocket by turning it counterclockwisewhile pressing in.3. To install the bulb, perform the removalsteps in reverse.
N00943501189N00943601920
1. Insert a straight
blade (or minus) screw-
driver with a cloth over its tip at the pointsindicated by arrows and pry gently toremove the cover (A).
Parking lights/Daytime running lights
NOTE
The parking lights and daytime runninglights use an LED in
stead of the bulb.
Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
Front turn signal lights
*: Front of the vehicle
Side turn signal lights
(if so
equipped)
NOTE
The side turn signal lights use an LEDinstead of the bulb. Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
Front fog lights (Halogen bulb type)
BK0249100US.book 36 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Cleaning the outside of your vehicle9-42 Vehicle care and maintenance
9
Salt and other chemicals used on winter roadsin some geographical areas can have a detri-mental effect on the vehicle underbody. Youshould flush the underbody with a high pres-sure hose every time you wash the outside ofyour vehicle.Take special care to remove mud or otherdebris which could trap and hold salt andmoisture.After washing your vehicle, wipe off allwaterdrops from the rubber parts around thedoors to prevent the doors from freezing.
N00946000205
Wax your vehicle once or twice a year, orwhen water does not bead up on the paint.Use a soft cloth to put a small amount of waxon the painted surfaces.
After the wax has
dried, polish with
a dry soft cloth.
Do not wax your vehicle in direct sunlight.You should wax when the painted surfacesare cool.
Never spray or splash water on the electricalparts in the engine compartment. This maydamage them. Be careful also when washingthe underbody to ensure that water does notenter the engine compartment.Avoid automatic car washers that use rotat-ing brushes. These br
ushes may scratch the
paint surface a
nd make it dull.
Scratches are more not
iceable on darker col-
ored vehicles.Some hot water wash
ing equipment uses
high pressure and heat
to clean your vehicle.
Because hot water can da
mage plastics parts
and seep inside your ve
hicle, make sure you
do the following when using such equip-ment:• Keep the washing nozzle at least 28 inches(70 cm) away from the vehicle body.• When washing around the door glass, holdthe nozzle at a distance of more than 28inches (70 cm) and at a right angle to theglass surface.
Make sure to do the following when using anautomatic car wash, with help from eitherthis manual or the car wash operator, toavoid damaging your vehicle:• Fold the outside
rearview mirrors.
• Tape or remove the rear wiper arm assem-bly.• If your vehicle is equi
pped with a roof rails,
check with the car wash operator beforeusing the car wash.CAUTION
• If your vehicle is e
quipped with the rain
sensor, place th
e wiper switch lever in the
“OFF” position to deac
tivate the rain sen-
sor.
During cold weather
NOTE
When the door is frozen, opening it by forcemay tear off or crack the rubber gasketinstalled around the door. Pour warm waterto melt the ice. Be
sure to thoroughly wipe
off the water after opening the door. To pre-vent freezing of the
weatherstripping on the
doors, hood, etc., treat
with silicone lubri-
cant.CAUTION
Waxing
CAUTIONWaxes containing high abrasive compoundsshould not be used. Th
ese waxes remove rust
and stain effectively fr
om the paintwork, but
are harmful to the finish of the paint, becausethey also remove
paint/clearcoat.
They are also harmful to other glossy sur-faces such as the grille, trim, moldings, etc.Do not use gasoline, benzine, kerosene orpaint thinners to remove
road tar or other dirt
from the vehicle surface.Do not put wax on the areas having blackmatte coating because
it can cause uneven
discoloration, patches, bl
urs, etc. If these get
wax on them, wipe the wax off right awaywith a soft clot
h and warm water.
BK0249100US.book 42 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Consumer information (For vehicles sold in U.S.A.)10-2 Customer assistance/Re
porting Safety Defects
10
N01047100171
This information is provided in compliancewith the requirements of the National High-way Traffic Safety Ad
ministration, Depart-
ment of Transportation. It provides thepurchasers and/or prospective purchaserswith information on repor
ting safety defects.
DOT quality grades - Al
l passenger vehicle
tires must conform to
Federal Safety Require-
ments in addition to these grades. The spe-cific grade rating in each grade category isshown on the side wall of the tires on yourvehicle. The treadwear grade is a comparative ratingbased on the wear rate of
the tire when tested
under controlled conditions on a specifiedgovernment test course
. For example, a tire
graded 150 would wear one and one-half(11/2) times as well on the government course
as a tire graded 100.
The relative performance
of tires depends upon the actual conditions of
their use, however, and may depart signifi-cantly from the norm due to variations indriving habits, service practices and differ-ences in road characteristics and climate. The traction grades, from highest to lowest,are AA, A, B and C. Those grades representthe tire’s ability to
stop on wet pavement as
measured under controlled conditions onspecified government te
st surfaces of asphalt
and concrete. A tire marked C may have poortraction performance. The temperature grades are A (the highest), Band C, representing the ti
re’s resistance to the
generation of heat and it
s ability to dissipate
heat when tested un
der controlled conditions
on a specified indoor
laboratory test wheel.
Sustained high temperature can cause the
material of the tire to
degenerate and reduce
tire life, and excessive temperature can leadto sudden tire failure. The grade C corre-sponds to a level of performance which allpassenger car tires must meet under the Fed-eral Motor Vehicle Safety Standard No. 109.Grades B and A represent higher levels ofperformance on the labora
tory test wheel than
the minimum required by law.
N01047201498
If you believe that your vehicle has adefect which could cause a crash orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in addi-tion to notifying Mitsubishi MotorsCorporation.
Consumer information (For vehicles sold in U.S.A.) Uniform tire quality grading Treadwear
Traction AA, A, B, C
WA R N I N GThe traction grade assi
gned to this tire is
based on straight-ahead braking tractiontests, and does not include acceleration,cornering, hydroplani
ng, or peak traction
characteristics.
Temperature A, B, C
WA R N I N GThe temperature grade for this tire isestablished for a tire that is properlyinflated and not overloaded. Excessivespeed, underinflation
, or excessive load-
ing, either separately
or in combination,
can cause heat buildup and possible tirefailure.
Reporting Safety Defects
BK0249100US.book 2 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Important facts to know
in case of an accident
10-4 Customer assistance/Re
porting Safety Defects
10
call (671)649-3673 or write to:To contact Triple J Motorscall (670)234-7133 or write to:To contact Pacific Marketing Inc.call 684(699)9140 or write to:
N01047300098
We hope you will never be involved in anaccident, but there is always that potentialdanger. So, please be sure to buckle up anddrive safely. Remain calm.Check for injuries. Report all injuries tothe police, and, if
necessary, call for an
ambulance.Record all the details of the accident. Thiswill provide you with accurate records ofthe accident for discussions with yourinsurance company and other personswho may be acting on your behalf. Understand your repair
estimate before
approving repairs.Choosing the repair shop and the brandsof parts that they use on your vehicle isyour decision.
Ask for genuine Mits
ubishi Motors parts.
Many times, to save
money, your insur-
ance company will recommend imitationparts that do not meet the original specifi-cations of fit, finish, corrosion resistanceor workmanship.
The strength and integrity built into yourMitsubishi vehicle is the result of a specificdesign referred to as
“Energy Management”.
Individual body parts are designed to act asone unit in the event of an accident. Shockwaves are absorbed by protective panels orare channeled around the passenger compart-ment. This important
feature is possible
because high tensile
steel is used in
Mitsubishi panels and structural parts, some-thing that cannot be guaranteed by the manu-facturers of imitation parts. All GenuineMitsubishi body panels
and support brackets
are designed and constructed as importantprotection features in the event of an acci-dent. By replacing body pa
rts with imitations,
your vehicle may no longer meet originalequipment specifications.
Triple J Enterprises, Inc.P.O. Box 6066TAMUNINGGUAM 96931For vehicles sold in Saipan Triple J MotorsP.O. Box 500487SAIPAN, MP96950-0487For vehicles sold in American Samoa Pacific Marketing, Inc.P. O . B o x 6 9 8PA G O PA G O ,AMERICAN SAMOA AS, 96799
Important facts to know in case of an accident In the event of an accident Key information to discuss with your insurance company
Mitsubishi Motors built-in pro-tection
BK0249100US.book 4 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Alphabetical index12-2
12
Fluid
....................................
9-11
, 11-7
Selector lever operation
...................
5-75
Selector le
ver positions
...................
5-79
Sports mode
...................................
5-80
Coolant (engine)
..........................
9-8
, 11-7
Cruise control
...................................
5-103
Cup holder
.......................................
5-242
D
Daytime running lights
Bulb capacity
.................................
9-32
Replacement
..................................
9-36
Defogger (rear window)
....................
5-225
Defrosting or defogging (windshield, door windows)
..................................
7-8
, 7-12
Dimensions
........................................
11-4
Dimmer (high/lo
w beam change)
.......
5-210
Disc brake pads
..................................
9-24
Dome light (front)/Reading lights
.......
5-236
Bulb capacity
.................................
9-33
Dome light (rear)
..............................
5-237
Bulb capacity
.................................
9-33
Doors
Lock
..............................................
5-34
Power door locks
............................
5-36
Driving during cold weather
..................
6-5
Driving precaution
................................
6-2
Driving, alcohol and drugs
.....................
6-2
Dual-zone automatic climate control air conditioner
........................................
7-5
E
ECO mode switch
.............................
5-218
Electric parking brake
..........................
5-54
Electric power steering system (EPS)
....
5-99
Electric rear window
defogger switch
..5-225
Electronic immobilizer (Anti-theft starting system)
.....................................
5-4
, 5-28
Electronically cont
rolled 4WD system
..5-82
Emission-control system maintenance
...
9-23
Engine
Compartment
...................................
9-5
Coolant
...................................
9-8
, 11-7
Hood
...............................................
9-3
Malfunction indicator light
.............
5-204
MIVEC
.................................
5-26
, 5-67
Oil and oil filter
.......................
9-6
, 11-7
Overheating
.....................................
8-4
Serial number
.................................
11-2
Specification
...................................
11-6
Engine hood
........................................
9-3
Engine switch
.....................................
5-18
Exhaust system
...................................
9-24
F
Floor console box
..............................
5-240
Floor mat
.............................................
6-3
Fluid
Automatic transaxle fluid
.......
9-11
, 11-7
Brake fluid
............................
9-13
, 11-7
Continuously variable transmission (CVT)fluid
...................................
9-11
, 11-7
Engine coolant
........................
9-8
, 11-7
Engine oil
...............................
9-6
, 11-7
Rear axle oil
..........................
9-12
, 11-7
Transfer oil
...........................
9-12
, 11-7
Washer fluid
.........................
9-12
, 11-7
Fluid capacities and lubricants
.............
11-7
Forward Collision Miti
gation System (FCM)
5-118Free-hand advanced security transmitter (F.A.S.T.-key)
..................................
5-13
Front fog lights
Bulb capacity
.................................
9-32
Indicators
.....................................
5-202
Replacement
..................................
9-36
Switch
.........................................
5-218
Front side-marker lights
Bulb capacity
.................................
9-32
Replacement
..................................
9-35
Front turn signal light
Bulb capacity
.................................
9-32
Replacement
..................................
9-36
Fuel
Filling the fuel tank
...........................
3-3
Fuel economy
...................................
6-2
BK0249100US.book 2 ページ ２０１７年５月１０日　水曜日　午前８時４９分