ECU MITSUBISHI OUTLANDER III 2018 User Guide

Seat belts4-20 Seat and restraint systems
4
3. Grasp the latch plate and slide it up thewebbing so that it ea
sily pulls across your
body. 4. Pull the seat belt out slowly while holdingthe latch plate. Push the latch plate intothe buckle until you hear a “click”. Pullup on the belt to be su
re the latch plate is
locked securely in the buckle.
5. The lap part of the belt must always beworn low and snug across the hips. Pullup on the shoulder portion of the belt totake up any slack
in the lap belt.
NOTE
If the seat belt lock
s up and cannot be pulled
out, pull it once with fo
rce and let it retract
all the way. Then, pull the belt out
slowly once again.
NOTE
With the exception of the seat belt for thedriver, the seat belts in
all other seating posi-
tions are equipped with an Automatic Lock-ing Retractor (ALR) function. If you pull theseat belt fully out of th
e retractor, the retrac-
tor will switch to its ALR child restraintinstallation function (see page 4-32).When the ALR function has been activated,the seat belt will only re
tract. If this happens,
let the belt fully retract, then pull the seatbelt back out, repeating steps 1 through 4.WA R N I N GBe sure the lap belt portion fits snugly andis worn as low as possible across the hips,not around the waist. Failure to follow thisinstruction will increase the risk of seriousinjury or death in the
event of an accident.
Be sure the seat belt webbing is nottwisted when worn. Twisted webbing mayadversely affect seat belt performance.
BK0249100US.book 20 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belts
Seat and restraint systems 4-23
4
N00418401394
A tone and warning light are used to remindthe driver to fasten the seat belt.If the ignition switch is turned to the “ON”without the driver’s seat belt being fastened, a
warning light will co
me on and a tone will
sound for approximately
6 seconds to remind
you to fasten your seat belt.If the vehicle is driven with the seat belt stillunfastened, the warning light will blink andthe tone will sound inte
rmittently until the
seat belt is fastened. At the same time, “FAS-TEN SEAT BELT” is displayed on the infor-mation screen in the multi informationdisplay (Type 1 only).
N00418301247
The front passenger seat
belt warning light is
located in the instrument panel.When the ignition switch is turned to the“ON” position or the operation mode is put inON, this indicator
normally comes on and
goes off a few seconds later.The light comes on when a person sits on thefront passenger seat bu
t does not fasten the
seat belt. It goes off when the seat belt is sub-sequently fastened.
Driver’s seat belt reminder/warning light and display Type 1Type 2
WA R N I N GIn order to reduce the risk of seriousinjury or death in an
accident, always fas-
ten your own seat belt
. Do not allow any-
one to ride in your ve
hicle unless he or she
is also seated and fastening a seat belt.Children should additi
onally be restrained
in a secure child restraint system.NOTE
If the seat belt subse
quently remains unfas-
tened, the warning li
ght and the tone will
issue further warnings
each time the vehicle
starts moving from a stop.
Front passenger seat belt warn-ing light
BK0249100US.book 23 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belts4-24 Seat and restraint systems
4
N00406301354
The seat belt shoulder
anchor height can be
adjusted. To move the anchor down, press thelock knob (A) and slide the anchor down tothe desired position. To move the anchor up,slide the anchor up to the desired position.
N00406501112
When seat belts for the second row outboardseating position and for the third row are notused, the seat belts can be stored.
WA R N I N GWhen a child booster se
at is used on the
front passenger seat, the front passengerseat belt warning ligh
t will not come on, if
the seat belt is not fastened when thebooster seat is used
. Confirm that the
child is wearing the
seat belt properly.
Do not install any acce
ssory or sticker that
makes the light difficult to see.
Adjustable seat belt shoulder anchor (front seats) Anchor down Anchor up
WA R N I N GAlways adjust the shou
lder belt anchor so
that the shoulder belt
is positioned across
the center of your shoulder without touch-ing your neck. The sh
oulder belt should
not be able to fall off your shoulder. Fail-ure to follow this instruction can adverselyaffect seat belt performance and increasethe risk of serious in
jury or death in the
event of an accident.Adjust the shoulder be
lt anchor only when
the vehicle is not in motion.Make sure the anchor is securely locked inposition after adjusting it.
Storing the second row (out-board seating positions) and third row seat belts
BK0249100US.book 24 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems4-30 Seat and restraint systems
4
N00418801167
The outboard seating pos
itions in the second
row seat of your vehicle are equipped withlower anchors for attaching child restraintsystems compatible with the LATCH system.
N00418901201
Your vehicle has 3 at
tachment points on the
backside of the second
row seats. These are
for securing a child restraint system tetherstrap to each of the 3 rear seating positions inyour vehicle.
N00419000198N00419101301
1. In order to securely
fasten the tether strap,
remove the head restraint from the loca-tion where you wish to install the childrestraint system.2. Open the gap a little between the seatcushion (A) and the seatback (B) withyour hand to locate the lower anchors (C).
Installing a child restraint sys-tem using the LATCH (Lower Anchors and Tethers for chil-dren) system Lower anchor locations
NOTE
The symbols on the seatback show the loca-tion of the lower anchor points.
Tether anchor locations
Examples of child restraint sys-tems compatible with the LATCH system A- Rear-facing child restraint systemB- Front-facing child restraint systemC- Child restraint system lower anchor
connectors
D- Tether strap
(These are only examples.)
Using the LATCH system
BK0249100US.book 30 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-31
4
3. For easier access, the seatback may berecline rearward.Push the anchor connectors (D) on thechild restraint system into the loweranchors (C) in accordance with theinstructions provided by the child restraintsystem’s manufacturer.After it is security fastened, adjust theseatback to 4 steps forward from mostreclined position.Remember, the lower anchors (C) pro-vided with your vehi
cle are designed to
secure suitable child restraint systemscompatible with the LATCH system inthe outboard positions of the secondrow seats only. The anchor connectorsare NOT designed to secure a suitablechild restraint system in the middleseating position of the second row seat.
4. Latch the tether strap hook (E) of the childrestraint system to the tether anchor bar(F) and tighten the tether strap so it issecurely fastened.5. Push and pull the chil
d restraint system in
all directions to ensure it is firmlysecured.
A- Vehicle seat cushionB- Vehicle seatbackC- Lower anchor
D- Connector
NOTE
In order to secure a child restraint systemcompatible with the LATCH system, use thelower anchor points in the outboard positionsof the second row seat. It is not necessary touse the vehicle’s seat
belt. The vehicle’s seat
belt, however, MUST be
used to secure a
child restraint system in the middle seatingposition of the second row seat.WA R N I N GIf there is any foreign material in oraround the lower an
chors, remove it
before installing the child restraint sys-tem. Also, make sure the seat belt is awayfrom, not looped through or otherwiseinterfering with, the child restraint sys-tem. If foreign matter is not removedand/or the seat belt
interferes with the
child restraint system, the child restraintsystem will not be secured properly, coulddetach and move forw
ard in the event of
sudden braking or an
accident, and could
result in injury to the child or other vehi-cle occupants.When the vehicle is
moving, do not adjust
the seat where the child restraint system isinstalled.
NOTE
If it is difficult to
latch the tether strap hook,
turn the hook sideways.WA R N I N GChild restraint system tether anchors aredesigned only to with
stand loads from cor-
rectly fitted child restraint systems. Underno circumstances are they to be used foradult seat belts, harnesses, for attachingother items, or equipment to the vehicle.
BK0249100US.book 31 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems4-32 Seat and restraint systems
4
N00407301553
With the exception of the driver, the seat beltin all other seating pos
itions can be converted
from normal Emergency Locking Retractor(ELR) mode, to Automatic Locking Retractor(ALR) mode. This mean
s that when you pull
the seat belt fully out of the retractor, theretractor will switch to its ALR child restraint
installation function.
Always use the ALR
child restraint installation function when youinstall a child restraint system using the seatbelt.Children 12 years old and under shouldalways be restrained in the rear seat, when-ever possible, although the front passengerseat belt can also be converted to ALR mode.
1. Place the child restraint system on the seatwhere you wish to install it.To help assure proper fitting of the childrestraint system, alwa
ys remove the head
restraint.When installing the front-facing childrestraint system on the second row seat,adjust the angle of the second row seat-back to the most upright position.
When using a child restraint in a rearseating position, always review theinstructions provided with that restraintto make sure it is compatible with thisvehicle and to understand how to properlyinstall it.Child restraints, incl
uding booster seats,
come in different sizes and configurations.Depending on where you
place these child
restraints, and depending on their size andconfiguration, you may not be able toaccess or properly use one or more adja-cent seat belt assemblies. If this occurs,the adjacent seating po
sition or positions
should not be used. Failure to use a seatbelt or improper use of a seat belt canresult in serious inju
ry or death should a
crash occur.
Installing a child restraint sys-tem using the seat belt (with emergency/auto
matic locking
mechanism)
WA R N I N G
WA R N I N GWhen you install a child restraint systemusing the seat belt, al
ways make sure the
retractor has been switched to the ALRchild restraint installation function. TheALR function will keep the child restraintsystem tightly secured to the seat.Failure to convert the retractor to theALR function may allow the childrestraint system to move forward duringsudden braking
or an accide
nt, resulting
in serious injury or
death to the child or
other occupants.
When using a child restraint in a rearseating position, al
ways review the
instructions provided with that restraintto make sure it is compatible with thisvehicle and to understand how to properlyinstall it.Child restraints, including booster seats,come in different sizes and configurations.Depending on where you
place these child
restraints, and depending on their size andconfiguration, you may not be able toaccess or properly use one or more adja-cent seat belt assemblies. If this occurs,the adjacent seating po
sition or positions
should not be used. Failure to use a seatbelt or improper use of a seat belt canresult in serious inju
ry or death should a
crash occur.
Installation
WA R N I N G
BK0249100US.book 32 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-33
4
2. Route the seat belt through the childrestraint system acco
rding to the instruc-
tions provided by the child restraint sys-tem’s manufacturer. Then insert the seatbelt latch plate into
the buckle. Make sure
you hear a “click” when you insert thelatch plate into the buckle.
3. To activate the ALR child restraint instal-lation function, slowly pull the shoulderpart of the belt all the way out of theretractor until it stops. Then let the beltfeed back into the retractor.4. After the belt has retracted, tug on it.If the belt is in the ALR function, you willnot be able to pull it out. If the webbingcan be pulled out from retractor, the ALRfunction has not been activated and youwill need to repeat steps 3 and 4.
5. After confirming that the belt is locked,grab the shoulder part of the belt near thebuckle and pull up to remove any slackfrom the lap part of the belt allowing theslack to feed into the retractor. Remember,if the lap belt portion is not tight, the childrestraint system
will not be secure. It may
help to put your weight on the childrestraint system and/or push on its seat-back while pulling up on the belt (Seeillustration).
If your child restraint system requires the useof a tether strap, fasten the tether strap inaccordance with the following procedures.
BK0249100US.book 33 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Maintenance and inspection of seat belts4-34 Seat and restraint systems
4
6. Latch the tether strap hook (A) of thechild restraint system to the tether anchorbar (B) and tighten the tether strap so it issecurely fastened.
7. Before putting your child in the restraint,push and pull the restraint in all directionsto be sure it is firmly secure. Do thisbefore each use. If the child restraint sys-tem is not firmly s
ecure, repeat steps 1
through 6.8. To remove a child restraint system fromthe vehicle and deac
tivate the ALR mode,
remove the child from the restraint.Unlatch the buckle. Th
en remove the belt
from the restraint and let the belt fullyretract.9. Reinstall the head restraint.Refer to “Head restraints” on page 4-11.
N00407601628
Children who have outgrown a child restraintsystem should be seated in the rear seat andwear the seat belt. If the shoulder belt crossestheir face or neck, and/
or the lap belt crosses
their stomach, a commercially availablebooster seat must be used to raise the child sothat the shoulder belt
crosses their shoulder
and the lap belt remains positioned lowacross their hips. The booster seat should fitthe vehicle seat and ha
ve a label certifying
compliance with Federal Motor VehicleSafety Standards or Mo
tor Vehicle Restraint
Systems and Booster Se
ats Safety Regula-
tions.
N00407001390
Regularly check your seat belt buckles andtheir release mechanisms for positive engage-ment and release of the latch plate. Check theretractors for automatic locking when in theAutomatic Locking Retractor function.The entire seat belt assembly should bereplaced if the webbing shows any obvious
NOTE
If it is difficult to la
tch the tether strap hook,
turn the hook sideways.WA R N I N GChild restraint system tether anchors aredesigned only to with
stand loads from cor-
rectly fitted child restraint systems. Underno circumstances are they to be used foradult seat belts, harnesses, for attachingother items, or equipment to the vehicle.
Children who have outgrown child restraint systems
WA R N I N GAny child who is too small to properlywear a seat belt
must be properly
restrained in an appropriate childrestraint system, to reduce their risk ofserious injury or de
ath in an
accident.
A child should never be
left unattended in,
or unsupervised around, your vehicle.When you leave the ve
hicle, always take
the child out as well.Children can die from heat stroke if left ortrapped inside the vehicle, especially onhot days.Keep your vehicle locked when not in use.Keep your vehicle keys away from chil-dren.
Maintenance and inspection of seat belts
BK0249100US.book 34 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Supplemental Restraint System (SRS) - airbag
Seat and restraint systems 4-35
4
cuts, tears, increase in thickness in any sec-tion of the webbing from broken fibers, orsevere fading from sunlig
ht. All of these con-
ditions indicate a weakening of the belt,which may adversely affe
ct seat belt perfor-
mance in an accident.
N00407701889
This vehicle is equippe
d with a Supplemental
Restraint System (SRS), which includes air-bags for the driver and passengers.The SRS front airbags are designed to supple-ment the primary protection of the driver andfront passenger seat belt systems by provid-ing those occupants w
ith protection against
head and chest injuries
in certain moderate to
severe frontal collisi
ons. The SRS front air-
bags, together with sensors at the front of thevehicle and sensors attached to the frontseats, form an advanced airbag system.The SRS driver’s knee airbag is designed tosupplement the primary protection of thedriver’s seat belt system. It can reduce theforward movement of the driver’s lower legsand provide increased
overall body protection
in certain moderate to
severe frontal colli-
sions.The SRS side airbags and the curtain airbagsare also designed to supp
lement the seat belts.
The SRS side airbags provide the driver andfront passenger with pr
otection against chest
injuries by deploying the bag on the sideimpacted in moderate
to severe side impact
collisions. The SRS curtain airbags provide
the driver and the passengers on the front seatand the second row outboard seats with pro-tection against head injuries by deploying thecurtain airbag on the si
de impacted in moder-
ate to severe side imp
act collisions and by
deploying both curtain
airbags when a roll-
over is detected. The curtain airbags are alsodesigned to help reduce the risk of completeand partial ejection fro
m the vehicle through
side windows in both side impact and roll-over type accidents.The SRS airbags are NOT a substitute for useof the seat belts. For maximum protection inall types of accident
s, seat belts must
ALWAYS be worn by everyone who drives orrides in this vehicle
(with infants and small
children in an appropriate child restraint sys-tem in the rear seat, and older children buck-led in the rear seat). Refer to “Child restraintsystems” on page 4-27.
WA R N I N GDo not attempt to repair or replace anypart of the seat belt assemblies. This workshould be done
by an authorized
Mitsubishi Motors dealer. Failure to havean authorized Mits
ubishi Motors dealer
perform the work could reduce the effec-tiveness of the belts and could result in aserious injury or de
ath in an accident.
Never use an organic solvent to clean theseat belt webbing. Do not attempt tobleach or re-dye th
e seat belt webbing.
These may weaken the
seat belt webbing,
increasing risk of in
jury or death in an
accident.Clean seat belt webbing only with mildsoap or detergent solution and rinse itwith lukewarm water, and dry the seatbelt webbing completely before retractingit.
Supplemental Restraint Sys-tem (SRS) - airbag
BK0249100US.book 35 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Supplemental Restraint System (SRS) - airbag4-40 Seat and restraint systems
4
bag control unit controls deployment of thepassenger’s front airbag in accordance withthe information it receives from this system.The passenger’s front airbag will not deployin an impact when the system senses no occu-pant on the front passenger’s seat or a child ina child restraint system. In this case, the pas-senger airbag off indi
cator will come on.
Refer to “Passenger’s ai
rbag off indicator” on
page 4-40.If there is a problem involving the passen-ger’s seat occupant cl
assification sensor sys-
tem, the SRS warning light in the instrumentpanel will come on. Refer to “SRS warninglight/display” on page 4-41.
N00418101346
The passenger’s airbag off indicator islocated in the instrument panel.The indicator normally comes on when theignition switch is turned to the “ON” positionor the operation mode is put in ON, and goesout a few seconds later.
In the following situ-
ations, the indicator will stay on to show thatthe passenger front airb
ag is not operational.
The front passenger’s seat is not occupied.
WA R N I N GIf any of the follow
ing conditions occur,
you should immediatel
y have your vehicle
inspected by an au
thorized Mitsubishi
Motors dealer as soon as possible:• The SRS warning light does not initiallycome on when the ignition switch or theoperation mode is under the followingconditions.[Except for vehicles equipped with theF. A . S . T. - k e y ]The ignition switch is in the “ON” or“START” position.[Vehicles equipped with the F.A.S.T.-key]The operation mode is in ON.• The SRS warning light does not go outafter several seconds.
• The SRS warning li
ght comes on while
you are driving.
To ensure that the passenger’s seat occu-pant classification sensor system can sensecorrectly, observe the following instruc-tions. Failure to follow these instructionscan adversely affect
the performance of
the passenger’s airbag system.• Adjust the seat to the correct position,and sit well back
against the seatback.
Refer to “Front seats” on page 4-4.• Do not recline the seatback more thannecessary.• Never have more th
an one person (adult
or child) sitting on the seat.• Do not place anything between the seatand the floor console.• When attaching a child restraint system,secure it firmly.• Do not place luggage or other objects onthe seat.• Do not use a seat cover or a cushion.• Do not modify or re
place the seat and
seat belt.• Do not place luggage or other objectsunder the seat.• Do not place and use
an electronic device
such as a computer on the seat.• Do not place heavy obje
cts on the seat or
stick pins, needles, or other objects intoit.• Do not remove the seat cushion skin.WA R N I N G
• If any liquid is spilled on the seat, wipe itand dry the seat immediately.
If the vehicle is involved in a severeimpact, have the SRS sensors inspected byan authorized
Mitsubishi Motors dealer as
soon as possible.
Passenger’s airbag off indicator
WA R N I N G
BK0249100US.book 40 ページ ２０１７年５月１０日　水曜日　午前８時４９分