tire type MITSUBISHI OUTLANDER III 2018 Owner's Manual

How to change a tire
For emergencies 8-11
8
8. Lower the vehicle slowly until the tiretouches the ground, by rotating the wheelnut wrench counterclockwise.9. Tighten the nuts in the order shown in theillustration until each
nut has been tight-
ened to the torque listed here.65 to 80 ft-lb (88 to 108 N•m)
10. Lower the jack all the way and remove it.11. Check the tire inflation pressure. The rec-
ommended tire pressure for your vehicleis listed on the tire
and loading informa-
tion placard attached to the driver’s doorsill as shown in the illustration. Refer to“Tire inflation pressures” on page 9-19.
NOTE
If all 4 aluminum wheels are changed to steelwheels, use tapered nuts.
CAUTIONNever use your foot or a pipe extension toapply added force to the wheel nut wrenchwhen tightening the wheel nuts. If you do so,you can over-tighten the wheel nuts anddamage the wheel, wheel nuts and hub bolts.
CAUTIONDriving with an imprope
rly inflated tire can
cause an accident. If
you have no choice but
to drive with an under-inflated tire, keepyour speed down and avoid sudden steeringor braking, if possible. Inflate the tire to thecorrect pressure as s
oon as possible. Refer to
“Tire inflation pressures” on page 9-19.After changing the tire
and driving the vehi-
cle about 620 miles (1,000 km), retighten thewheel nuts to make sure
that they have not
come loose.If the steering wheel vibrates when drivingafter changing the tire, have the tire checkedfor balance at an authorized MitsubishiMotors dealer or a repair facility of yourchoice.Do not mix one type of tire with another oruse a different size from the one listed. Thiswould cause ea
rly wear and poor handling.
BK0249100US.book 11 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tires
Vehicle care and maintenance 9-15
9
N00939201651
It is important to familiarize yourself with thefollowing terms:Cold tire pressure:• The measured pressure after the vehiclehas been parked for
at least three hours,
or• The measured pressure when the vehicleis driven less than 1 mile (1.6 km) afterhaving been parked for three hours.
Maximum pressure: the maximum per-missible cold tire inflation pressure forthis tire.Recommended inflation pressure: theinflation pressure for optimum tire perfor-mance.Intended outboard sidewall:• The sidewall that
contains a whitewall,
bears white lettering or bears manufac-turer, brand, and/or model name moldingthat is higher or deeper than the samemolding on the other sidewall of the tire,or
• The outward facing si
dewall of an asym-
metrical tire that has a particular sidethat must always face outward whenmounted on a vehicle.
Passenger car tire: a
tire intended for use
on passenger cars, multipurpose passen-ger vehicles, and trucks
that have a gross
vehicle weight rati
ng (GVWR) of 10,000
pounds or less.Light truck (LT) tire: a tire designated byits manufacturer as primarily intended foruse on lightweight truc
ks or multipurpose
passenger vehicles.Tread: portion of a ti
re that comes into
contact with the road.Tread rib: a tread se
ction running circum-
ferentially around a tire.Tread separation: pulling away of thetread from the tire carcass.Carcass: the tire structure, except treadand sidewall rubber wh
ich, when inflated,
bears the load.Sidewall: portion of
a tire between the
tread and bead.Section width: the lin
ear distance between
the exteriors of th
e sidewalls of an
inflated tire, excluding elevations due tolabeling, decoration,
or protective bands.
Bead: the part of the tire that is made ofsteel wires, wrapped or reinforced by plycords and that is shaped to fit the rim.
NOTE
Check each battery terminal for corrosion.You can prevent further corrosion by wash-ing with a solution of
baking soda and water.
Grease the posts and cl
amps after cleaning or
tightening them.Ensure the battery is securely installed andcannot be moved. Also
check each terminal
for tightness.If you will not be driv
ing your vehicle for a
long period of time, re
move the battery and
store it in a place where the battery fluid willnot freeze. The batter
y only should be stored
with a full charge.Before cleaning the battery, tighten all thefiller port caps to keep
dirt and moisture out.
Tires
WA R N I N GDriving with tires that are worn, damagedor improperly infl
ated is dangerous.
These type tire conditions will adverselyaffect vehicle performance.These type tire conditions can also cause atread separation or blowout which mayresult in an accident causing seriousinjury or death.
Tires, including spar
e tire, degrade over
time with age even when they are notbeing used.It is recommended that tires over 6 yearsgenerally be replaced
even if damage is
not obvious.WA R N I N G
BK0249100US.book 15 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tires
Vehicle care and maintenance 9-19
9
N00939301997
Proper tire inflation pre
ssure is essential for
the safe and satisfac
tory operation of your
vehicle. The wrong tire pressure will causeproblems in three major areas:SafetyToo little pressure increases flexing in thetire and can cause tire failure. Too muchpressure can cause a tire to lose its abilityto cushion shock. Objects on the road andpotholes could then ca
use tire damage that
may result in tire failure.EconomyThe wrong tire pressu
re can cause uneven
wear patterns in the tire tread. Theseabnormal wear patter
ns will reduce the
tread life, and the tire will have to bereplaced sooner.Too little pressure also makes it harder forthe tire to roll, and this uses up more fuel.Ride comfort and vehicle stabilityThe superior riding e
xperience built into
your vehicle partly de
pends on the correct
tire pressure. Too much pressure gives anuncomfortable and jarring ride. Too littlepressure feels as if
your vehicle is slow to
respond.Unequal tire pressure
s can make steering
your vehicle uneven
and unpredictable.
The tire pressure for your vehicle under nor-mal driving conditions is listed on the placardattached to the driver’s door sill.(Refer to “Tire and loading information plac-ard” on page 11-3.)The recommended inflation pressures undernormal driving conditions should be used forthe tires listed below.Tire pressures should be checked, andadjusted if necessary, at least once a month.Pressures should be checked more oftenwhenever weather temperatures changeseverely, becaus
e tire pressures change with
outdoor temperatures. The pressures listedare always “cold in
flation pressure”.
Cold inflation pressure is measured after thevehicle has been parked for at least threehours or is driven less than 1 mile (1.6 km)after having been parked for three hours.Cold inflation pressure must not go above themaximum values molded into the tire side-wall. After driving several miles, your tireinflation pressure may increase 2 to 6 psi (14
to 41 kPa) from the cold inflation pressure.Do not let air out of the tires to get back to thespecified cold pressure, or your tires will betoo low.Check your tires each t
ime you refuel. If one
tire looks lower than the others, check thepressure for all of them.You should also take the following safety pre-cautions:Keep your tires inflated to the recom-mended pressures. (See the tire and load-ing information placard attached to thedriver’s door sill.)Stay within the recommended load limits.Make sure that the weight of any load inyour vehicle is evenly distributed.Drive at safe speeds.After filling your tires to the correct pres-sure, check them for damage and airleaks. Be sure to reinstall the caps on thevalve stems.
N00939601479
Tire inflation pressures
Item
Tire size
Front
Rear
Normal tire
P215/70R16P225/55R18
240 KPA, 35 PSI
240 KPA, 35 PSI
Compact spare wheel
T155/90D16T155/80D17
420 KPA, 60
PSI
Replacing tires and wheels
CAUTIONAvoid using different size tires from the onelisted and the combined use of differenttypes of tires, as this can affect drivingsafety.Refer to “Tires and wheels” on page 11-7.
BK0249100US.book 19 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tires9-20 Vehicle care and maintenance
9
N00939700141
The following maintenance steps are recom-mended:Check tire pressures regularly.Have regular maintenance done on thewheel balance and front and rear suspen-sion alignment.Rotate your tires regul
arly as described in
the “Tire rotation” section on page 9-20.
N00939800184
Tread wear indicators are built into the origi-nal equipment tires on
your vehicle to help
you know when your tires should be replaced.
Many states have la
ws requiring that you
replace your tires at this point.These indicators are molded into the bottomof the tread grooves and will appear when thetire tread is worn down to 1/16 inch (1.6mm).When the bands appear next to one another intwo or more places
, replace your tires.
N00939901528
To even out the wear on your tires and makethem last longer, Mitsubishi Motors Corpora-tion recommends that y
ou rotate your tires at
the mileage listed in the “WARRANTY ANDMAINTENANCE MANUAL”.However, the timing for tire rotation mayvary according to your vehicle condition,road surface conditions, and your own per-sonal driving habits. Any time you noticeunusual wear, rotate your tires as soon as pos-sible.When rotating tires,
check for uneven wear,
damage, and wheel alignment. Abnormalwear is usually caused by a wrong tire pres-
On all-wheel drive vehi
cles, always use tires
of the same size, same
type, and same brand,
and which have no wear differences. Usingtires that differ in si
ze, type, brand or the
degree of wear, will in
crease the differential
oil temperature, resul
ting in possible damage
to the driving system. Further, the drive trainwill be subjected to ex
cessive loading, possi-
bly leading to oil leakage, component sei-zure, or other serious problems.Only Mitsubishi Motors Authorized wheelsshould be used, beca
use your vehicle is
equipped with a tire pr
essure monitoring sys-
tem.Use of another type of
wheel risks air leaks
and sensor damage, as
it will not be possible
to install the tire pressure sensor properly.NOTE
On vehicles with Elec
tric parking brake, 16
inches steel wheel cannot be used on yourvehicle because it interfe
res with brake parts.
Additionally, 16 inches aluminum wheelmay not be used on your vehicle dependingon its type, even if a Mitsubishi Motors Gen-uine wheels.Consult an authorized Mitsubishi Motorsdealer before using
wheels that you have.
CAUTION
Tire maintenance Tread wear indicator 1- Location of the tread wear indicator2- Tread wear indicator
NOTE
Tire wear indicators ca
n have different marks
and locations depending
on the tire manufac-
turer.
Tire rotation
BK0249100US.book 20 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tires
Vehicle care and maintenance 9-21
9
sure, wheels that are not aligned properly,wheels that are out-of-balance, or severebraking.Check with an authorized Mitsubishi Motorsdealer or a repair fac
ility of your choice to
find out the reason for uneven tread wear.The first tire rotation is the most importantone. It will allow all your tires to wear evenly.
N00940000320
In some areas of the country, snow tires arerequired for winter driving. If snow tires arerequired in your area, you must choose snowtires of the same size
and type as the original
tires provided with your
vehicle. Snow tires
should also be
installed on all four wheels.
Otherwise your safety
and vehicle handling
can be reduced.Even where laws may permit it, snow tiresshould not be operated
at sustained speeds
over 75 mph (120 km/h).
CAUTIONA compact spare tire can be installed tempo-rarily in place of a tir
e that has been removed
during the tire rotation. However, it must notbe included in the regular tire rotationsequence.
Tires that do not have arrows showing rotation directionTires that have arrows s
howing rotation direction
FrontFront
If the tires have arrows (A) indicating thecorrect direction of rotation, swap the frontand rear tires on the left-hand side of thevehicle and the front and rear tires on theright-hand side of th
e vehicle separately.
Keep each tire on its original side of thevehicle. When installing the tires, make surethe arrows point in the
direction in which the
wheels will turn when the vehicle moves for-ward. Any tire whose
arrow points in the
wrong direction will not
perform to its full
potential.CAUTIONAvoid the combined use of different types oftires. Using different t
ypes of tires can affect
vehicle performance and safety.CAUTIONFront
Snow tires
CAUTIONOnly Mitsubishi Motors Authorized wheelsshould be used, beca
use your vehicle is
equipped with a tire pr
essure monitoring sys-
tem.Use of another type of wheel risks air leaksand sensor damage, as it
will not be possible
to install the tire pressure sensor properly.
BK0249100US.book 21 ページ ２０１７年５月１０日　水曜日　午前８時４９分

General maintenance9-24 Vehicle care and maintenance
9
high heat sources such
as the exhaust mani-
fold.
N00941400187
If the fuel-vapor vent line is clogged or dam-aged, the fuel-vapor mixture will escape, pol-luting the air.Have the system checked at an authorizedMitsubishi Motors dealer at the mileage spec-ified in the “WARRANTY AND MAINTE-NANCE MANUAL”.
N00941501299
The next pages list th
e maintenance service
recommended by Mitsubishi Motors Corpo-ration. In addition to the general maintenancethat needs to be performed at the times listed,
there are other parts which do not usuallyneed regular maintenance.But, if any of these parts stops working prop-erly, your vehicle performance could suffer.Have these items checked if you notice aproblem with them.If you have any questions, see your autho-rized Mitsubishi Motors
dealer for assistance.
N00941600059
Good brakes are essential for safe driving.Check the brake pads for wear. For goodbraking performance, replace the brake padswith the same type pa
ds as the originals.
N00941700076
Brake hoses and tubing should be checkedfor:Severe surface cracking, scuffing or wornspots. If the fabric casing of the hose isshowing through any cracks or worn spotsin the rubber hose cover, the hose shouldbe replaced. The brakes can fail if thehose wears through.Improper installati
on may cause twisting,
or wheel, tire or
chassis interference.
N00941800093
Check the following parts for damage andgrease leaks:Ball joint boots of the suspension andsteering linkageBellows on both ends of the drive shaft
N00942201118
The best way to keep carbon monoxide gasfrom entering inside your
vehicle is to have
the engine exhaust syst
em properly serviced.
Have a competent mechanic inspect the com-plete exhaust system
and nearby body areas
for broken, damaged, deteriorated, or mispo-sitioned parts if you no
tice any of the follow-
ing:A change in the sound of the exhaust sys-temThe smell of exhaust fumes inside thevehicle
WA R N I N GIf you see a fuel leak
or if you smell fuel,
do not run the engine. Any spark (includ-ing from the ignition
), flame or smoking
material could cause an explosion or fire.Call an authorized
Mitsubishi Motors
dealer or a repair fa
cility of your choice
for assistance.
Evaporative emission control system (except evaporative emission canister) General maintenance
Disc brake pads Brake hoses
Ball joint, steering linkage seals, drive shaft boots Exhaust system
WA R N I N GCarbon monoxide gas
from your vehicle’s
exhaust is poisonous. Breathing thesefumes can cause unconsciousness or death.
BK0249100US.book 24 ページ ２０１７年５月１０日　水曜日　午前８時４９分