warning lights MITSUBISHI OUTLANDER SPORT 2012 3.G User Guide

Features and controls
3-167
3
Warning display list (With ignition switch or operation mode is in OFF)
N00558000211
Screen type 1
Screen type 2
Cause
Do this (Reference)

You have forgotten to remove the key
from the ignition switch.
Remove the key.
Refer to “Key reminder system” on
page 3-40.

You have forgotten to turn off the
lights.Refer to “Light auto-cutout function (head-
lights and other lights)” on page 3-191.

The theft-alarm system is operating. Refer to “Theft-alarm system” on page 3-48.

Immobilizer is registered. Refer to “Customer key programming
(Except for vehicles sold in Canada)” on
page 3-6.
Refer to “Customer F.A.S.T.-key program-
ming (Except for vehicles sold in Canada)”
on page 3-32.
BK0140300US.book 167 ページ ２０１１年６月２８日　火曜日　午後５時１８分

3-182 Features and controls
3Indicators
N00519900127
Turn signal indicators/Hazard warning lights
N00520000216
The arrows will flash in time with the corresponding exterior
turn signals when the turn signal lever is used.
Both arrows will flash when the hazard warning flasher switch
is pressed.NOTE
If the indicator flashes faster than usual or if the indicator
stays on without flashing, check for a malfunctioning turn
signal light bulb or turn signal connection.High beam indicator
N00520100086
A blue light comes on when the headlights are on high beam.Front fog light indicator
(if so equipped)
N00520200175
This indicator comes on while the front fog lights are on.Position indicator
N00551300026
This indicator light illuminates while the position lights are on.ECO mode indicator
(if so equipped)
N00568800023
This indicator will be displayed when fuel-efficient driving is
achieved.
Warning lights
N00520300147
Brake warning light
N00520400470
This light comes on when the ignition switch is turned to the
“ON” position (engine off) or the operation mode is put in ON.
When the engine is started, the light should go off a few sec-
onds later. A warning is also displayed in the multi-information
display.
The warning light also illuminates after starting the engine
under the following conditions.

When the parking brake is still applied.

When the brake fluid level is low.

When the brake system circuit is not working properly.
Before driving, be sure that the parking brake is fully released
and brake warning light is off.
BK0140300US.book 182 ページ ２０１１年６月２８日　火曜日　午後５時１８分

Features and controls
3-183
3
Engine malfunction indicator (“SERVICE
ENGINE SOON” or “Check engine light”)
N00520500716
This indicator is a part of the onboard diagnostic (OBD) sys-
tem which monitors the emissions, engine control system or
continuously variable transmission (CVT) control system. If a
problem is detected in one of these systems, this indicator
comes on. When the ignition switch is turned to the “ON” posi-
tion or the operation mode is put in ON, this indicator normally
comes on and goes off after the engine has started.
This indicator will come on if the fuel tank filler cap is not
properly tightened. If this indicator comes on and stays on after
refueling, stop the engine and check that the cap is properly
tightened. (Turn the cap clockwise until you hear clicking
sounds.)
If this indicator does not go off after several seconds or lights
up while driving, have the system checked as soon as possible
at an authorized Mitsubishi Motors dealer or a repair facility of
your choice.
CAUTION
!
If the brake warning light and the Anti-lock braking
system warning light are illuminated at the same
time, the braking force distribution function will not
operate, so the vehicle may be destabilized during
sudden braking under the following conditions.
• When the brake warning light does not go out even
when the parking brake is released.
• When the brake warning light stays on while driv-
ing.
• If the above occurs, avoid sudden braking and
high-speed driving. Park the vehicle in a safe
place, and contact an authorized Mitsubishi
Motors dealer or a repair facility of your choice as
soon as possible.

The vehicle should be brought to a halt in the follow-
ing manner when brake performance is deterio-
rated.
• Confirm that the vehicle slows down when you
press down on the brake pedal harder than usual.
In some cases, the brake pedal may go all the way
to the floor.
• Should the brakes fail, use engine braking to
reduce your speed and slowly apply the parking
brake.
Depress the brake pedal to illuminate the stop
lights to alert the vehicles behind you.
CAUTION
!
Driving for a long time with the engine malfunction
indicator on may cause more damage to the emission
control system. This could also affect fuel economy
and drivability.
If this indicator does not come on when the ignition
switch is turned to the “ON” position or the opera-
tion mode is put in ON, have the system checked at
an authorized Mitsubishi Motors dealer or a repair
facility of your choice.
BK0140300US.book 183 ページ ２０１１年６月２８日　火曜日　午後５時１８分

3-186 Features and controls
3
Charging system warning display
N00558600103
Ty p e 1
Ty p e 2
If there is a fault in the charging system, the warning display
warning is displayed on the information screen in the multi-
information display. The warning light in the instrument cluster
also illuminates.

If the brake warning display, brake warning light,
and the Anti-lock braking system warning light are
illuminated at the same time, the braking force dis-
tribution function will not operate, so the vehicle
may be destabilized during sudden braking. Avoid
sudden braking and high-speed driving. Park the
vehicle in a safe place, and contact an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.
The vehicle should be brought to a halt in the follow-
ing manner when brake performance is deterio-
rated.
• Confirm that the vehicle slows down when you
press down on the brake pedal harder than usual.
In some cases, the brake pedal may go all the way
to the floor.
• Should the brakes fail, use engine braking to
reduce your speed and slowly apply the parking
brake.
Depress the brake pedal to illuminate the stop
lights to alert the vehicles behind you.CAUTION
!
CAUTION
!
If warnings are displayed while the engine is run-
ning, park your vehicle in a safe place as soon as
possible and contact an authorized Mitsubishi
Motors dealer or a repair facility of your choice to
have the system checked.
BK0140300US.book 186 ページ ２０１１年６月２８日　火曜日　午後５時１８分

3-192 Features and controls
3
NOTE
When the engine is started using the key, if the driver’s
door is opened and the key is removed, the headlight
reminder buzzer intermittently emits a high-pitched
sound. If the key is still in the ignition switch the key
reminder buzzer intermittently emits a low-pitched sound.
The buzzer stops when the driver’s door is closed. (A
warning is also displayed in the multi-information dis-
play.)

When the engine is started using the F.A.S.T.-key, if the
driver’s door is opened and the operation mode is put in
OFF, the headlight reminder buzzer intermittently emits a
high-pitched sound. If the operation mode is in any mode
other than OFF, the operation mode on reminder buzzer
intermittently emits a low-pitched sound.
The buzzer stops when the driver’s door is closed. (A
warning is also displayed in the multi-information dis-
play.)
Headlight reminder buzzer
N00549800200
[When using a key to start the engine]
If the driver’s door is opened with the key in the “LOCK” or
“ACC” position or removed from the ignition switch while the
lights are on, the tone will sound to remind you to turn off the
lights.
[When using the F.A.S.T.-key to start the engine]
If the driver’s door is opened with the operation mode is put in
OFF or ACC, or if the operation mode is changed to OFF while
the lights are on, the tone will sound to remind you to turn off
the lights.
In either case, the lights will turn off automatically and so will
the tone. Or you can turn the light switch to the “OFF” position
to stop the tone.
BK0140300US.book 192 ページ ２０１１年６月２８日　火曜日　午後５時１８分

3-198 Features and controls
3Hazard warning flasher switch
N00522700275
If you press the flasher switch, the front and rear turn signals
will flash intermittently, and so will the hazard warning lights.
This is an emergency warning system and should not be used
when the vehicle is in motion, except for emergencies.
If you need to leave your vehicle, the flashers will keep work-
ing after the ignition switch is removed or the operation mode
is put in OFF.NOTE
If the flashers are used for several hours, the battery will
run down. This could make it difficult or impossible to
restart your vehicle.
Front fog light switch
(if so equipped)
N00522800393
The front fog lights illuminate only when the headlights are on
low beam.
Turning the knob in the direction of the “ON” position turns on
the front fog lights as well as the indicator in the instrument
cluster. To turn them off, turn the knob in the direction of the
“OFF” position.
The knob will return to the neutral position when it is released.NOTE
If the headlights are switched to high beam, the front fog
lights will go out; they will illuminate again when the
headlights are switched back to low beam.
BK0140300US.book 198 ページ ２０１１年６月２８日　火曜日　午後５時１８分

6-2 For emergencies
6If the vehicle breaks down
N00836300187
If your vehicle breaks down on the road, move to the shoulder
and turn on the hazard warning flashers. If there is no shoulder,
or the shoulder is not safe, drive in the right lane slowly, with
the hazard lights flashing, until you come to a safe stopping
place. Keep the flashers flashing.If the engine stops/failsIf the engine stops, there will be no power assist to the steering
and brakes, making these difficult to use.

The brake booster will not work, so the brakes will not
grip well. The brake pedal will be harder to press than
usual.

Since there is no power steering assist, the steering wheel
will be hard to turn.When the engine fails at the intersectionGet help from your passengers, bystanders, etc. to push the
vehicle and move it to a safe zone.
Jump-starting the engine
N00836400700
If the engine cannot be started because the battery is weak or
dead, you can start it with the battery from another vehicle
using jumper cables.
1. Take off any metal jewelry such as watch bands or brace-
lets that might make an accidental electrical contact.
2. Position the vehicles close enough together so that the
jumper cables can reach, but be sure the vehicles aren’t
touching each other.
WA R N I N G
!
When using jumper cables to start a vehicle, follow
the procedures and be very cautious.
CAUTION
!
Do not try to start your vehicle by pushing or tow-
ing. Vehicles with automatic transaxles cannot be
started this way. Also, there is more risk of an acci-
dent when a vehicle is being pushed or towed.
CAUTION
!
Check the other vehicle. It must have a 12-volt bat-
tery. If the other system isn’t 12-volt, both systems
can be damaged.
BK0140300US.book 2 ページ ２０１１年６月２８日　火曜日　午後５時１８分

7-42 Vehicle care and maintenance
7
Passenger compartment fuse location tablePassenger compartment fuse location
Sub fuse block Main fuse block
No.
Symbol
Electrical system
Capacity
1 Heater 30 A*
2Stop lights
(Brake lights)15 A
3 Rear fog light 10 A
4 Windshield wiper 30 A
5 Optional 10 A
6 Door locks 20 A
7Radio15 A
8 Control unit relay 7.5 A
9Interior lights
(Dome lights)15 A
10 Hazard warning flasher 15 A
11 Rear window wiper 15 A
12 Gauges 7.5 A
13Cigarette lighter
/Accessory socket15 A
14Ignition
Switch10 A
15 Sunroof 20 A
16 Outside rearview mirrors 10 A
17 All-wheel drive system 10 A
BK0140300US.book 42 ページ ２０１１年６月２８日　火曜日　午後５時１８分

Alphabetical index
1
A
Accessory (installation) 1-7
Active stability control (ASC) 3-105
Air bag 2-43
Air cleaner filter 7-12
Air conditioning
Automatic air conditioning 5-25
,5-35
Important air conditioning operating tips 5-45
Manual air conditioning 5-6
,5-16
Air purifier 5-46
Aluminum wheels 7-75
Antenna
Roof antenna 5-102
Anti-lock braking system 3-99
Arm rest 2-9, 2-11
Assist grip 3-259
Audio 5-46
Error codes 5-95
,5-96
External audio input function 5-91
Handling of compact discs 5-100
Steering wheel audio remote control switch 5-92
Automatic air conditioning 5-25
,5-35
Automatic transaxle
Fluid 9-9
B
Back-up light
Bulb capacity 7-48Replacement 7-65
Ball joint, steering linkage seals and drive shaft boots 7-37
Battery 7-17
Charging system warning light 3-184
Checking battery electrolyte level 7-18
Disconnection and connection 7-22
During cold weather 7-21
Specification 9-8
Bluetooth 2.0 interface 3-210
Bottle holders 3-257
Brake
Fluid 9-9
Brake assist system 3-98
Braking 4-8
Anti-lock braking system 3-99
Hose 7-37
Pad wear alarm 3-96
Parking brake 3-59
Pedal 3-95
Pedal free play 7-33
Power brakes 3-95
Service brake 3-95
Warning lights 3-182
Break-in recommendations 3-2
Bulb capacity 7-48
C
California Perchlorate Materials Requirements 1-9
Capacities 9-9
BK0140300US.book 1 ページ ２０１１年６月２８日　火曜日　午後５時１８分

Alphabetical index
2Card holder 3-243
Cargo area cover 3-258
Cargo loads 4-13
Cargo room light
Bulb capacity 7-50
Catalytic converter 7-3
Cautions on the handling of all-wheel drive vehicles 3-93
Certification label 9-5
Charging system warning light 3-184
Child restraint systems 2-31
Child safety locks for rear door 3-43
Cleaning
Inside of your vehicle 7-70
Outside of your vehicle 7-71
Clock 5-103
Clutch
Pedal free play 7-32
Coat hook 3-259
Consumer information 8-2
Continuously variable transmission (CVT) 3-76
Fluid 7-14
,9-9
Selector lever operation 3-77
Selector lever positions 3-81
Sports mode 3-82
Coolant (engine) 7-10
,9-9
Cruise control 3-109
Cup holder 3-256
D
Daytime running lights
Bulb capacity 7-48
Replacement 7-61
Defogger (rear window) 3-208
Defrosting or defogging (windshield, door windows)
5-14
,5-23
,5-33
,5-43
Dimensions 9-5
Dimmer (high/low beam change) 3-193
Disc brake pads 7-37
Dome light
Bulb capacity 7-50
Doors
Lock 3-38
Power door locks 3-41
Driving during cold weather 4-7
Driving precaution 4-2
Driving, alcohol and drugs 4-3
E
Electric rear window defogger switch 3-208
Electronic immobilizer (Anti-theft starting system) 3-4
,3-31
Electronically controlled 4WD system 3-86
Emission-control system maintenance 7-35
Engine
Compartment 7-6
Coolant 7-10
,9-9
Hood 7-4
BK0140300US.book 2 ページ ２０１１年６月２８日　火曜日　午後５時１８分