low beam MITSUBISHI OUTLANDER SPORT 2013 3.G Owners Manual

Overview
Outside
N00100601349
Power window P.3-52
Front turn signal lights
P.3-192, 7-48, 7-56 Engine hood P.7-4
Fuel tank filler P.1-4
Outside rearview mirrors
P. 3 - 6 4
Windshield wipers P.3-194
Front fog lights (if so equipped)
P.3-193, 7-48, 7-57 Side turn signal light
P.3-192, 7-48, 7-57
Headlights, low beam
P.3-188, 7-48, 7-50
Headlights, high beam
P.3-188, 7-48, 7-52
Front side-marker and parking lights
P.3-183, 7-48, 7-55
Daytime running lights (if so equipped)
P.3-183, 7-48, 7-60
BK0150700US.book 6 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Features and controls3-177
3
Indicators
N00519900127
Turn signal indicators/Hazard warning lights
N00520000216
The arrows will flash in time with the corresponding exterior
turn signals when the turn signal lever is used.
Both arrows will flash when the hazard warning flasher switch
is pressed.NOTE

If the indicator flashes faster than usual or if the indicator
stays on without flashing, check for a malfunctioning turn
signal light bulb or turn signal connection.High beam indicator
N00520100086
A blue light comes on when the headlights are on high beam.Front fog light indicator
(if so equipped)
N00520200175
This indicator comes on while the front fog lights are on.Position indicator
N00551300026
This indicator light illuminates while the position lights are on.ECO mode indicator
(if so equipped)
N00568800023
This indicator will be displayed when fuel-efficient driving is
achieved.
Wa r n i n g l i g h t s
N00520300147
Brake warning light
N00520400470
This light comes on when the ignition switch is turned to the
“ON” position (engine off) or the operation mode is put in ON.
When the engine is started, the light should go off a few sec-
onds later. A warning is also displayed in the multi-information
display.
The warning light also illuminates after starting the engine
under the following conditions.

When the parking brake is still applied.

When the brake fluid level is low.

When the brake system circuit is not working properly.
Before driving, be sure that the parking brake is fully released
and brake warning light is off.
BK0150700US.book 177 ページ ２０１２年３月２２日　木曜日　午後６時４６分

3-188 Features and controls
3
Dimmer (high/low beam change)
N00549900142
To change the headlights from high beam to low beam and vice
versa, pull the turn signal lever to (1). Switch the headlights to
low beam as a courtesy whenever there are oncoming vehicles,
or when there is traffic moving ahead of you. An illuminated
blue light in the instrument cluster indicates when the head-
lights are on high beam.
Headlight flasher
N00550000185
You can flash the high beams by pulling the lever gently
toward you (2). The lights will go back to normal when you let
go. While the high beam is on, you will see a blue light on the
instrument panel.NOTE
You can flash the high beams by pulling the lever toward
you, even if the light switch is off.

If you turn the lights off with the head lights set to high-
beam illumination, the headlights are automatically
returned to their low-beam setting when the light switch is
next turned to the “ ” position.
BK0150700US.book 188 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Features and controls3-189
3
Welcome light
N00563200064
This function turns on the front side-marker and parking lights
for about 30 seconds after the UNLOCK button (A) on the
remote control transmitter is pressed when the combination
headlights and dimmer switch is in the “OFF” or “AUTO”
position (for vehicles equipped with the automatic light con-
trol). On vehicles equipped with the automatic light control,
the welcome light function will operate only when it is dark
outside the vehicle.NOTE
While the welcome light function is operating, perform
one of the following operations to cancel the function. • Push the LOCK button (B) on the remote control trans-
mitter.
• Turn the combination headlights and dimmer switch to the “ ” or “ ” position.
• Turn the ignition switch to the “ON” position or put the operation mode in ON.

It is possible to modify functions as follows:
• The headlights can be set to come on in the low beam setting.
• The welcome light function can be deactivated.
For details, consult a Mitsubishi Motors dealer.
On vehicles equipped with Mitsubishi Multi-Communica-
tion System, screen operations can be used to make the
adjustment.
Refer to the separate owner’s manual for details.
BK0150700US.book 189 ページ ２０１２年３月２２日　木曜日　午後６時４６分

3-190 Features and controls
3
Coming home light
N00547300100
This function turns on the headlights in the low beam setting
for about 30 seconds after the ignition switch is turned to the
“OFF” position or the operation mode is put in OFF.1. Turn the combination headlights and dimmer switch to the “OFF” or “AUTO” position (for vehicles equipped with
the automatic light control).
2. Turn the ignition switch to the “OFF” position or put the operation mode in OFF. Also, if a key was used to start the
engine, remove the key from the ignition switch.
3. Within 60 seconds of turning the ignition switch to the “OFF” position or putting the operation mode in OFF, pull
the turn signal lever toward you. 4. The headlights will come on in the low beam setting for
about 30 seconds. After the headlights go off, the head-
lights can be turned on again in the low beam setting for
about 30 seconds by pulling the turn signal lever toward
you within 60 seconds of turning the ignition switch to the
“OFF” position or putting the operation mode in OFF. To
turn on the headlights again after 60 seconds of turning
the ignition switch to the “OFF” position or putting the
operation mode in OFF, repeat the process from step 1.
NOTE
While the coming home light function is operating, per-
form one of the following operations to cancel the func-
tion.
• Pull the turn signal lever toward you.
• Turn the combination headlights and dimmer switch to
the “ ” or “ ” position or put the operation mode in
ON.
• Turn the ignition switch to the “ON” position or put the operation mode in ON.

It is possible to modify functions as follows:
• The time that the headlights remain on can be changed.
• The coming home light function can be deactivated.
For details, consult a Mitsubishi Motors dealer.
On vehicles equipped with Mitsubishi Multi-Communica-
tion System, screen operations can be used to make the
adjustment.
Refer to the separate owner’s manual for details.
BK0150700US.book 190 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Features and controls3-191
3
Headlight leveling switch
(if so equipped)
N00537100105
The direction of the headlight beam (the direction in which the
light shines) alters according to the number of people and the
load in the vehicle. Lower the headlight angle if it is too high
due to the number of people and/or the load in the vehicle so
that the headlights’ glare does not distract the drivers of
approaching vehicles. First set the light switch to the “ ”
position, then turn the headlight leveling switch knob to lower
the beam. The greater the number on the headlight leveling
switch knob, the lower the beam will point.
Set the switch to the appropriate position so that the headlight
beam is level with the road.
NOTE

Start adjusting when the knob is at the “0” position (when
the beam is at its highest).

Keep the knob in the “0” position except when using the
knob to lower the headlight beam angle.

Always return the knob to the “0” position when the load
is removed and the people have left the vehicle.
WARNING
!
To avoid distraction while driving, always perform
headlight adjustments before vehicle operation.
BK0150700US.book 191 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Features and controls3-193
3
Hazard warning flasher switch
N00522700275
If you press the flasher switch, the front and rear turn signals
will flash intermittently, and so will the hazard warning lights.
This is an emergency warning system and should not be used
when the vehicle is in motion, except for emergencies.
If you need to leave your vehicle, the flashers will keep work-
ing after the ignition switch is removed or the operation mode
is put in OFF.NOTE

If the flashers are used for several hours, the battery will
run down. This could make it difficult or impossible to
restart your vehicle.
Front fog light switch
(if so equipped)
N00522800393
The front fog lights illuminate only when the headlights are on
low beam.
Turning the knob in the direction of the “ON” position turns on
the front fog lights as well as the indicator in the instrument
cluster. To turn them off, turn the knob in the direction of the
“OFF” position.
The knob will return to the neutral position when it is released.NOTE
If the headlights are switched to high beam, the front fog
lights will go out; they will illuminate again when the
headlights are switched back to low beam.
BK0150700US.book 193 ページ ２０１２年３月２２日　木曜日　午後６時４６分

4-6 Driving safety
4
TiresCheck all the tires for heavy tread wear or uneven wear pat-
terns. Look for stones, nails, glass, or other objects stuck in the
tread. Look for any tread cuts or sidewall cracks. Check the
wheel nuts for tightness, and the tires (including spare tire) for
proper pressure. Replace your tires before they are heavily
worn out.
As your vehicle is equipped with a tire pressure monitoring
system, there is a risk of damage to the tire inflation pressure
sensors when the tire is replaced on the rim. Tire replacement
should, therefore, be performed only by an authorized
Mitsubishi Motors dealer.LightsHave someone watch while you turn all the exterior lights on
and off. Also check the turn signal indicators and high-beam
indicators on the instrument panel.Fluid leaksCheck the ground under the vehicle after parking overnight, for
fuel, water, oil, or other leaks. Make sure all the fluid levels are
correct. Also, if you can smell fuel, you need to find out why
immediately and have it fixed.
Safe driving techniques
N00629200094
Even this vehicle’s safety equipment, and your safest driving,
cannot guarantee that you can avoid an accident or injury.
However, if you give extra attention to the following areas, you
can better protect yourself and your passengers:
Drive defensively. Be aware of traffic, road and weather
conditions. Leave plenty of stopping distance between
your vehicle and the vehicle ahead.

Before changing lanes, check your mirrors and use your
turn-signal light.

While driving, watch the behavior of other drivers, bicy-
clists, and pedestrians.

Always obey applicable laws and regulations. Be a polite
and alert driver. Always leave room for unexpected
events, such as sudden braking.

If you plan to drive in another country, obey their vehicle
registration laws and make sure you will be able to get the
right fuel.
BK0150700US.book 6 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-43
7
Engine compartment fuse location tableEngine compartment fuse location
Behind the fuse block cover
No.
Symbol
Electrical system
Capacity
1 Front fog lights 15 A
2 Engine7.5 A
3 Automatic transaxle 20 A
4 Horn10 A
5 Alternator7.5 A
6 Headlight washer 20 A
7 Air conditioning 10 A
8 ETV/Oil cooler fan
(Twin Clutch SST) 15 A
9 Security horn20 A
10 Wiper deicer15 A
11 — ——
12 Power gate30 A
13 Daytime running lights 10 A
14 Headlight
(high beam) (left) 10 A
15 Headlight
(high beam) (right) 10 A
16 Headlight
(low beam) (left) Discharge 20 A
BK0150700US.book 43 ページ
２０１２年３月２２日　木曜日　午後６時４６分

7-44 Vehicle care and maintenance
7
*: Fusible link
Some fuses may not be installed on your vehicle, depend-
ing on the vehicle model or specifications.

The table above shows the main equipment corresponding
to each fuse.
There are no 7.5 A, 25 A or 30 A spare fuses. If a fuse of one of
these capacities blows, replace it temporarily by borrowing one
of the fuses indicated below.
7.5 A: 10 A spare fuse
25 A: 20 A spare fuse
30 A: 30 A audio amplifier fuse
Replace the borrowed fuse with a fuse that has the correct
capacity as soon as possible.
17 Headlight
(low beam) (right) Discharge 20 A
18 Headlight
(low beam) (left) Halogen 10 A
19 Headlight
(low beam) (right) Halogen 10 A
20 ENG/POWER 10 A
21 Ignition coil 10 A
22 ENG/POWER 20 A
Fuel line heater 25 A
23 Fuel pump 15 A
24 Starter 30 A*
25 — — —
26 Anti-lock braking system 40 A*
27 Anti-lock braking system 30 A*
28 Air conditioning condenser fan
motor 30 A*
29 Radiator fan 40 A*
30 IOD IOD 30 A
31 Audio amplifier 30 ANo.
Symbol
Electrical system
Capacity
32 Diesel30 A
33 — Spare fuse10 A
34 — Spare fuse15 A
35 — Spare fuse20 ANo.
Symbol
Electrical system
Capacity
BK0150700US.book 44 ページ ２０１２年３月２２日　木曜日　午後６時４６分