lock MITSUBISHI OUTLANDER XL 2013 Owner's Manual

Seat and restraint systems
2-27
2
NOTE
The head restraint height in the third row seats cannot be
adjusted.
For instructions regarding on how to use the third row
seats, refer to “Third row seat (Seating 7 passengers)” on
page 2-16.
Adjustment of the head restraint height (The
front and second row seats)To reduce the risk of injury in an accident, adjust the head
restraint height so that the center of the restraint is at your eye
level when seated. Any person too tall for the restraint to reach
their eye level when seated should raise the restraint to the
highest locked position.

To raise the restraint, pull it straight up.

To lower the restraint, push down on it while pressing the
lock knob (A) in the direction shown by the arrow.

After adjusting the height, push down on the restraint to
make sure it is locked in position.
WA R N I N G
!
Driving without the head restraints in place can
cause you and your passengers serious injury or
death in an accident. To reduce the risk of injury in
an accident, always make sure the head restraints
are installed and properly positioned when the seat
is occupied.
In order to minimize the risk of a neck injury due to
a rear impact, the seatback must be adjusted to the
upright position and the head restraint must be
adjusted to the proper position before vehicle opera-
tion. The driver should never adjust the seat while
the vehicle is in motion.
Never place a cushion or similar device on the seat-
back. This can adversely affect head restraint per-
formance by increasing the distance between your
head and the restraint.
BK0150600US.book 27 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-28 Seat and restraint systems
2
To remove (The front and second row seats)Press the lock knob (A) in the direction shown by the arrows.
Then pull the head restraint up and out of the seatback.To install (The front and second row seats)First check that the head restraint is facing in the right direction
as shown in the previous illustration, and then insert it into the
seatback. Push the head restraint down while pressing the lock
knob (A) until the restraint locks into place.
WA R N I N G
!
To help minimize the risk of neck injury in the event
of an accident, the head restraints must be properly
installed and positioned to proper height before
vehicle operation.
CAUTION
!
Check that the lock knob (A) is extended out as
shown in the illustration. Then pull the head
restraint up to make sure that it is locked in place
and will not come out of the seatback.
BK0150600US.book 28 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-31
2
2. Operate the lever (A) or lock release strap (B) on the sec-
ond row seats to fold down the seatbacks.3. For vehicles with 2nd row seat slide function, the seatback
will fall forward and the entire seat will flip up as it slides
forward.Operating the leverOperating the lock release strap
BK0150600US.book 31 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-33
2
To put the seat back in its normal position1. While supporting the seat with your hand, pull the lock
release strap (A) on the backside of the seat cushion and
keep it pulled as you lower the seat flat.
CAUTION
!
For vehicles equipped with a third row seat, be care-
ful not to catch the feet of any passengers sitting in
the third row seat, when returning the second row
seats to their original position.
BK0150600US.book 33 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-34 Seat and restraint systems
2
2. Push down on the entire seat until it locks into place with
a click.NOTE
You can load luggage with the seatback folded down.3. While pulling on the lock release strap on the back of the
seatback, raise up the seatback.
4. After returning the seatback to its normal position, gently
shake the seat and seatback to make sure they are firmly
secured.
BK0150600US.book 34 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-35
2
5. Raise all the head restraints to the highest position.
Refer to “Head restraints: Adjustment of the head restraint
height” on page 2-26.
Making a flat seat
N00404800156
The entire interior of the vehicle may be used for sleeping
accommodations by removing the head restraints and fully
reclining all the seats when the vehicle is stopped.
WA R N I N G
!
After returning the seat to its normal position, raise
all the head restraints to the highest position. Using
the second row seat with the head restraints
retracted could cause a serious head injury or death
in the event of a collision or sudden breaking.
WA R N I N G
!
Never drive with passengers or cargo on the flat
seat. This is extremely dangerous and can cause
severe or fatal injury or death in an accident or if
heavy braking is required.
CAUTION
!
Adjust the seats only when the vehicle is stopped in a
safe place.
Seat should be adjusted only by adults to avoid acci-
dents.
When sliding the seats, be careful not to catch your
hand or leg.
Do not walk around on top of the seats after they
have been laid flat because the footing is uneven. It
is safest to move about on your hands and knees.
To ensure the seats are locked securely, attempt to
move them back and forth.
Do not jump on or drop heavy objects on the seat-
backs.
BK0150600US.book 35 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-36 Seat and restraint systems
2
1. Remove the head restraints from the front seats and raise
the arm rest on the second row seats.
For vehicles with a cargo area cover, remove the cover.
(Refer to “Head restraints” on page 2-26, “Arm rest” on
page 2-11 and “Cargo area cover” on page 3-288.)

To raise the seatback, firmly place your hand on the
seatback, pull the seatback lock knob up, and raise
the seatback slowly. (Refer to “To adjust the seat-
back” on page 2-8 and page 2-13.) Do not let chil-
dren adjust the seatback.
CAUTION
!
BK0150600US.book 36 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-40 Seat and restraint systems
2
Seat belt instructions
N00406200444
All seats are equipped with a seat belt which uses one com-
bined lap-and-shoulder belt with an emergency locking retrac-
tor.
This system is designed to provide both comfort and safety. It
permits full extension and automatic retraction of the belts dur-
ing normal vehicle operation. A sensing device inside the belt
retractor is designed to lock the retractor in the event of a sud-
den change in the vehicle’s motion.NOTE
For instructions on installing a child restraint system using
a seat belt, refer to “Installing a child restraint system
using the seat belt” on page 2-57.1. Occupants should always sit back in their seats with their
backs against the upright seatback. To reduce the risk of
serious injury or death during deployment of the air bag,
adjust the driver’s seat as far back as possible while main-
taining a position that still enables you to fully apply the
pedals, easily control the steering wheel, and safely oper-
ate the vehicle. The front passenger seat should also be
moved as far back as possible. Refer to “Supplemental
Restraint System (SRS) - air bag” on page 2-61. Also
refer to “To adjust the seat forward or backward” on page
2-7.
BK0150600US.book 40 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-42 Seat and restraint systems
2
3. Pull the seat belt out slowly while holding the latch plate.
Push the latch plate into the buckle until you hear a
“click”. Pull up on the belt to be sure the latch plate is
locked securely in the buckle.NOTE
If the seat belt locks up and cannot be pulled out, pull it
once with force and let it retract all the way.
Then, pull the belt out slowly once again.4. The lap part of the belt must always be worn low and snug
across the hips. Pull up on the shoulder portion of the belt
to take up any slack in the lap belt.
BK0150600US.book 42 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-43
2
NOTE
With the exception of the seat belt for the driver, the seat
belts in all other seating positions are equipped with an
Automatic Locking Retractor (ALR) function. If you pull
the seat belt fully out of the retractor, the retractor will
switch to its ALR child restraint installation function (see
page 2-57).
When the ALR function has been activated, the seat belt
will only retract. If this happens, let the belt fully retract,
then pull the seat belt back out, repeating steps 1 through
4.
5. To release the belt, press the button on the buckle and
allow the belt to retract.
If the belt does not retract smoothly, pull it out and check
for kinks or twists in the webbing. Then make sure it
remains untwisted as it retracts.
Driver’s seat belt reminder/warning light and
display
N00418400313
Warning light
Warning display type 1
Warning display type 2
A tone and warning light are used to remind the driver to fasten
the seat belt.
If the ignition switch is set to the “ON” position without the
driver’s seat belt being fastened, a warning light will come on
and a tone will sound for approximately 6 seconds to remind
you to fasten your seat belt.
If you then drive with the seat belt unfastened for longer than a
minute from when the ignition switch was turned on, the warn-
ing light will come on and blink repeatedly and the tone will
sound intermittently.
The warning light and the tone will stop after approximately 90
seconds.
WA R N I N G
!
Be sure the lap belt portion fits snugly and is worn
as low as possible across the hips, not around the
waist. Failure to follow this instruction will increase
the risk of serious injury or death in the event of an
accident.
Be sure the seat belt webbing is not twisted when
worn. Twisted webbing may adversely affect seat
belt performance.
BK0150600US.book 43 ページ ２０１２年３月３０日　金曜日　午前１０時４３分