Maintenance MITSUBISHI PAJERO IV 2011 Owner's Guide

Bulb capacity
E01003200014
When replacing a
bulb, use a new bulb with the
same wattage and colour.
Outside E01003302631
Front1- Headlamps, high-beam: 65 W (H9)
2- Front fog lamps*: 55 W (H11)
3-
Headlamps,

low beam with discharge lamp:
35 W (D2S)
Headlamps, low beam without discharge
lamp: 55 W (H11)
4- Position lamps: 5 W (W5W)
5- Front turn-signal lamps: 21 W (WY21W) Codes in parentheses indicate bulb types. CAUTION
l
On vehicles with discharge headlamps, do
not attempt to

disassemble or repair dis-
charge headlamps, and do not attempt to
replace their bulbs. A high voltage is
present in the power circuit and in the
bulbs and bulb terminals. To avoid the
risk of an electric shock, contact a
MITSUBISHI MOTORS Authorized
Service Point whenever repair or replace-
ment is necessary.
3-door models 5-door models
Rear
6- High-mounted stop
lamp
(bulb type)*: 16 W
(W16W)
7- Licence plate lamps: 5 W (W5W)
8- Rear fog lamp: 21 W (W21W)
9- Tail lamps*: 5 W (W5W)
10- Rear turn-signal lamps*: 21 W (WY21W)
11- Rear turn-signal lamps*: 21 W (WY21W) 12- Stop and tail lamps*: 21/5 W (W21/5W)
Stop lamps*: 21/5 W (W21/5W)
13- Reversing lamps: 21 W (W21W) Codes in parentheses indicate bulb types.
NOTE l On
vehicles

with LED type high-mounted
stop lamp, do not attempt to repair or replace
it.
For repair and replacement, contact a
MITSUBISHI MOTORS Authorized Service
Point.
Inside E01003401244 1- Luggage compartment lamp: 8 W
2- Door courtesy lamps: 3.4 W
3-
Vanity mirror lamps*:

3 W
4- Room & map lamps: 8 W
5- Rear personal lamps: 8 W
6- Glove box lamp: 1.4 W Maintenance
8-24
8

OBKE12E1

Headlamps
E01003501199
Replacement of high-beam 1. Remove the bulb
and connector assembly
(A) by turning it anticlockwise. 2. Depress the tab (B) on the harness connector
and pull

the harness connector (C) to remove
it. 3. To
install the bulb, perform the removal
steps in reverse. Replacement of low beam (except for vehicles
with discharge headlamps)
1.Remove the bulb

and connector assembly
(A) by turning it anticlockwise. 2. Depress the tab (B) on the harness connector
and pull

the harness connector (C) to remove
it. 3. To install the bulb, perform the removal
steps in reverse. CAUTION
l
Handle halogen lamp
bulbs with care.
The gas inside halogen lamp bulbs is high-
ly pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the
bulb to break the next time the head-
lamps are operated. If the glass surface is
dirty, it must be cleaned with alcohol,
paint thinner, etc., and refit it after dry-
ing it thoroughly. Position lamps
E01003700471
1. Turn the bulb socket anticlockwise to re-
move it. Maintenance
8-25 8

OBKE12E1

2. Remove the bulb from the socket by pulling
out. 3. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps E01003800733
1. Turn
the
bulb socket anticlockwise to re-
move it.
2. Remove

the bulb from the socket by pulling
out. 3. To install the bulb, perform the removal
steps in reverse.
Front fog lamps* E01004001553
1. Remove the

5 clips (A, C) and screw (B) by
following procedures

then turn up the cover
(D). 2. Depress the tab (E) on the harness connector
(F) and

pull the harness connector to remove
it. 3. Remove the entire socket and bulb assembly
(G) by turning it anticlockwise. CAUTION
l
Handle halogen
lamp
bulbs with care.
The gas inside halogen lamp bulbs is high-
ly pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the
bulb to break the next time the fog lamps
are operated. If the glass surface is dirty,
it must be cleaned with alcohol, paint thin-
ner, etc., and refit it after drying thorough-
ly. Maintenance
8-26
8

OBKE12E1

4. To install the bulb, perform the removal
steps in reverse.
NOTE l When
refitting
the clips (H and I) of the cov-
er, push the pin (J). Rear combination lamps
E01004200659
On corner side 1.Remove the screws that hold the lamp unit.
2. Slide

the lamp unit out sideways to remove it.
Left side
Right side 3. Remove the socket and bulb assemblies by
turning them
anticlockwise. Remove the
bulb by pulling it out.
3-door models 5-door models A- Rear turn-signal lamp*
B- Stop and tail lamp* Stop lamp*
C- Reversing lamp
4.

To install the bulb, perform the removalsteps in reverse.
On bumper* 1. Remove the lens mounting screws. Maintenance
8-27 8

OBKE12E1

2. Remove the socket and bulb assembly togeth-
er by turning it anticlockwise, and then re-
move the bulb by pulling it out. D- Rear turn-signal lamp
E- Tail lamp
3. To install the

bulb, perform the removal
steps in reverse.
Rear fog lamp E01004100371
1. Open the spare wheel garnish (A). (Refer to
“To remove the spare wheel” on page 6-10). 2. Remove the socket and bulb assembly (B) by
turning it
anticlockwise, and then remove the
bulb by pulling it out. 3. To install the bulb, perform the removal
steps in reverse.
High-mounted stop lamp (bulb type)* E01004500535
1. Insert
a

straight blade (or minus) screwdriver
with a

cloth over at the edge of the cover and
pry gently to remove the cover. 2. Remove the socket and bulb assembly togeth-
er by
turning it anticlockwise, and then re-
move the bulb by pulling it out. 3. To install the bulb, perform the removal
steps in reverse.
Licence plate lamps E01004600709
1. Remove
the

lens mounting screws and re-
move the socket and bulb assembly. Maintenance
8-28
8

OBKE12E1

2. Remove the socket and bulb assembly (A) to-
gether by turning it anticlockwise and then re-
move the bulb by pulling it out. 3. To install the bulb, perform the removal
steps in reverse. NOTE
l When
installing the
lens, make sure the direc-
tion of the lens is installed as shown in the il-
lustration. *: Right side of the vehicle
Room & map lamps E01004700524
1. Insert a straight blade (or minus) screwdriver
with a

cloth over its tip into the lens and pry
gently to remove it. 2. Remove the bulb from the lamp holder.3. To install the bulb, perform the removal
steps in reverse.
NOTE l When installing

the lens, align the tab on the
lens with the hole on the vehicle side. Rear personal lamps
E01005200252
When replacing a bulb, keep the interior lamp
switch in the “ ” (OFF) position. Maintenance
8-29 8

OBKE12E1

1. Insert a straight blade (or minus) screwdriver
with a cloth over its tip into the notch of the
lens and pry gently to remove it. 2. Remove the bulb from the lamp holder.
3. To install
the

bulb, perform the removal
steps in reverse.
NOTE l When installing the lens, align the tab on the
lens with the hole on the vehicle side. Luggage compartment lamp
E01005300439
1. Insert a straight

blade (or minus) screwdriver
with a cloth over its tip into the notch of the
lens and pry gently to remove the lens. 2. Remove the bulb from the lamp holder.
3. To
install the

bulb, perform the removal
steps in reverse. NOTE
l When
installing the

lens, align the tabs on
the lens with the holes on the vehicle side. Door courtesy lamps
E01005400339
1. Insert a straight blade (or minus) screwdriver
with a

cloth over its tip into the edge of the
lens, pry gently to remove the lens.
Front Maintenance
8-30
8

OBKE12E1

Rear2. Remove the bulb from the lamp holder.
3. To install
the

bulb, perform the removal
steps in reverse.
NOTE l When installing the lens, align the 2 tabs on
the lens with the notches on the vehicle side. Glove box lamp
E01006100232
1. Pull out the bulb. 2. To
install the bulb, perform the removal
steps in reverse.
Vanity mirror lamps* E01006200262
1. Insert
a

straight blade (or minus) screwdriver
with a

cloth over its tip into the notch of the
lens and pry gently to remove it. 2. Remove the bulb from the lamp holder.
3. To install the

bulb, perform the removal
steps in reverse. Maintenance
8-31 8

OBKE12E1

Fuel consumption
E01101100661
3-door models Model Combined Urban conditions Extra-urban conditions
CO
2 (g/km) Fuel consumption
(L/100 km) CO
2 (g/km) Fuel consumption
(L/100 km) CO
2 (g/km) Fuel consumption
(L/100 km) 3200 models M/T
*1
207 7.8251 9.5181 6.9 M/T
*2
221 8.4271 10.3 1937.3 A/T
*1
216 8.2263 10.0 1897.2 A/T
*2
239 9.0286 10.8 2128.0 A/T
*3
220 8.4262 10.0 1967.43800 models
32213.4 42017.6 26711.2
*1 : Vehicles except for Russia, Ukraine and Kazakhstan
*2 : Vehicles for Russia, Ukraine and Kazakhstan
*3 : Vehicles with only the front seat NOTE
l The values shown above apply to a vehicle on which optional equipment has not been fitted.
l The results given do not express or imply any guarantee of the fuel consumption of the particular vehicle.
The
vehicle itself
has not been tested and there are inevitably differences between individual vehicles of the same model. In addition, this vehicle may incor-
porate particular modifications. Furthermore, the driver’s style and road and traffic conditions, as well as the extent to which the vehicle has been driven and
the standard of maintenance, will all affect its fuel consumption. Specifications
9-13 9

OBKE12E1

5-door models
Model Combined Urban conditions Extra-urban conditions
CO
2 (g/km) Fuel consumption
(L/100 km) CO
2 (g/km) Fuel consumption
(L/100 km) CO
2 (g/km) Fuel consumption
(L/100 km) 3000 models M/T
287 12.2 37215.8 23710.0 A/T
288 12.2 37515.9 23710.03200 models M/T
*1
213 8.1254 9.6189 7.2 M/T
*2
221 8.427110.3 1937.3 A/T
*1
224 8.526710.1 1997.5 A/T
*2
239 9.028610.8 2128.0 A/T
*3
228 8.626610.1 2067.83800 models
32413.5 42317.7 26811.2
*1 : Vehicles except for Russia, Ukraine and Kazakhstan
*2 : Vehicles for Russia, Ukraine and Kazakhstan
*3 : Vehicles with only the front seat NOTE
l The values shown above apply to a vehicle on which optional equipment has not been fitted.
l The results given do not express or imply any guarantee of the fuel consumption of the particular vehicle.
The
vehicle itself
has not been tested and there are inevitably differences between individual vehicles of the same model. In addition, this vehicle may incor-
porate particular modifications. Furthermore, the driver’s style and road and traffic conditions, as well as the extent to which the vehicle has been driven and
the standard of maintenance, will all affect its fuel consumption. Specifications
9-14
9

OBKE12E1