engine MITSUBISHI SPYDER 1990 Service Repair Manual

ENGINE Timing Belt
TIMING BELT REMOVAL,,
Caution
If timing belt “B” is to be reused, use
it with an arrow on its flat side indicating the tu rning
direction (to the right).
CounterbalanceINSTALLATION SERVICE POINTS
TIMING BELT INSTALLATION
Install timing belt
by the procedure.
(1) Ensure that crankshaft sprocket “B” timing mark and the
counterbalance shaft sprocket timing mark are align ed.
(2) Fit timing belt
over crankshaft sprocket “B” and the
silent shaft sprocket. Ensure that there is no slac k in
the belt.
BELT TENSION ADJUSTMENT
Adjust the tension of timing belt by the following procedure.
(1) Temporarily fix the timing belt tensioner such that
the center of the tensioner pulley is to the left a nd above
the center of the installation bolt, and temporarily attach
the tensioner pulley so that the flange is toward t he front
of the engine.,
(2) Holding the timing belt “B” up with your
in the direction of the
belt so that the tension side of the belt is taut.
Now tighten
the bolt to fix the tensioner.. ,
Caution
When tightening the ensure that the
pulley shaft does not rotate, with
it to rotate with the bolt can
on the belt.
(3) Press the belt at the shown point by check
belt tension. If not,
S t a n d a r d v a l u e : 5 - 7 m m
. ,
TSB Revision

E N G I N E T i m i n g
Crankshaft
sprocketCrankshaft
Crankshaft
blade Crankshaft
sprocket
I
CRANKSHAFT SENSING BLADE
When installing, make sure the direction is correct
. See figure.
CRANKSHAFT SPROCKET INSTALLATION
Use the special tool to install the crankshaft spro cket and
bolt.
NOTE
Apply the minimum amount of engine oil to the beari ng
Revision

ENGINE
OVERHAUL.
CONTENTS
CRANKSHAFT, FLYWHEEL ANDDRIVE PLATE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
CYLINDER HEAD AND VALVES . . . . . . . . . . . 34
EXHAUST MANIFOLD AND
WATER PUMP. . . . . . . . . . . . . . . . . . . . . . . . . . . .27
FRONT CASE, COUNTERBALANCE SHAFT
AND OIL PAN
. . . . . . . . . . . . . . . . . . . . . . . . . . . .40
FUEL AND EMISSION CONTROL
PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . 2
GENERATOR AND IGNITION SYSTEM . . 11
INTAKE MANIFOLD. . . . . . . . . . . . . . . . . . . . . . .25
PISTON AND CONNECTING . . . .. . .
ROCKER ARMS AND CAMSHAFT . . . . . . . . .29
SEALANTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
SPECIAL TOOLS. . . . . . . . . . . . . . . . . . . . . . . . . . .8
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . .3
TIMING BELT. . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

ENGINE OVERHAUL General Information
GENERAL SPECIFICATIONS
TSB Revision

ENGINE OVERHAUL
Crankshaft, flywheel and drive plate,
Cylinder block
REWORK DIMENSIONS
Cylinder head and valve
Crankshaft, flywheel and drive plate
TORQUE SPECIFICATIONS
Generator and ignition system
I‘
TSB Revision

ENGINE OVERHAUL
.
Cylinder head and valves
14.5
Front case, counterbalance shaft and oil pan
14
Piston and connecting rod
Crankshaft, flywheel and drive plate. .
case
1
,
TSBRevision

ENGINE OVERHAUL
SEALANTS
TSB Revision

ENGINE OVERHAUL Special Tools,
TSB Revision

ENGINE OVERHAUL
TSB Revision

ENGINE OVERHAUL Tools
,
6991654
bolt
TSB Revision