CD player MITSUBISHI TRITON 1997 User Guide

CHASSIS ELECTRICAL ± Radio and Tape Player54-74
C-3 No sound from one speaker.
Clean the tape player head and check again.Ye sOK
No
Replace the tape player and check again.Ye sRepair or replace tape player.
No
Remove the connector on the back of the radio and check
the speaker harness for conductance.Ye sIt conducts electricity but is
shorted out.Repair harness.
No
Check the speaker for conductance.Ye sRepair harness.
No
Repair or replace speaker.
C-4 Sound quality is poor, or sound is weak.
Does the player play properly when another tape* is inserted?Ye sOK
No
*:

Ensure that the tape label is not loose, that the tape
itself is not deformed and that the tape is tightly wound.

Tapes of C-120 or greater length often get caught in
the mechanism and should not be used.
Does the player play properly when the tape player head is cleaned?Ye sOK
No
Is proper operation obtained when the tape player is replaced?Ye sRepair or replace tape player.
No
Repair or replace speaker.
C-5 Cassette tape will not be ejected.
The problems covered here are all the result of
the use of a bad tape (deformed or not properly
tightened) or of a malfunction of the tape player
itself. Malfunctions involving the tape becoming
caught in the mechanism and ruining the case arealso possible, and attempting to force the tape out
of the player can cause damage to the mechanism.
The player should be taken to a service dealer
for repair.

CHASSIS ELECTRICAL ± Radio and Tape Player54-76
C-8 Tape gets caught in mechanism*1.
*1
When the tape is caught in the mechanism, the case may
not eject. When this occurs, do not try to force the tape
out as this may damage the tape player mechanism. Take
the cassette to a service dealer for repair.
Does the player play OK if the tape*2 is changed?Ye sTape used is bad.
No
*2
Ensure that the tape label is not loose, that the tape itself
is not deformed and that the tape is tightly wound. Also,
tapes of C-120 or greater length often get caught in the
mechanism and should not be used.
Repair or replace tape player.

CHASSIS ELECTRICAL ± Radio and Tape Player54-77
RADIO AND TAPE PLAYER WITH ANTI-THEFT SYSTEM54400430032

After the power supply to the radio and tape
player has been interrupted for an hour or more,
the anti-theft system will prevent the radio and
tape player from working, even if the powersupply is restored. Problem with the anti-theft
system can be found using the flow chart below.
When the ignition key is in the ACC or ON position and the POWER
button is pressed, does ªCODEº appear on the display?NoCheck and repair the connector or harness.
Ye s
Can the security code be input to the display using the memory
select buttons?NoRepair or replace the radio and tape player.
Ye s
If the BAND button is pressed after security code has been input,
do the radio and tape player then work?Ye sNormal
No
If the security code is not accepted, is ª1 ERRORº displayed for
two seconds and then changes into ªcodeº to wait for the next
input?NoRepair or replace the radio and tape player.
Ye s
If the BAND button are pressed after the security code has been
input again by means of the memory select buttons, do the radio
and tape player then work?Ye sNormal (an incorrect code was input the first time)
No
If the security code is not accepted, is ª2 ERRORº displayed for
two seconds and then changes into ªcodeº to wait for the next
input?NoRepair or replace the radio and tape player.
Ye s
If the BAND button are pressed after the security code has been
input again by means of the memory select buttons, do the radio
and tape player then work?Ye sNormal (an incorrect code was input the second time)
No
If the security code is not accepted, ª3 ERRORº is displayed for
five seconds and then changes into ªOFFº. Then the security code
can not be input any more. To input the security code again, turn
the ignition switch to the ACC or ON position and wait for one
hour when ªOFFº is displayed. After ªOFFº disappears on the display
and changes into ªcodeº, the security code can be input again.