lock MITSUBISHI TRITON 1997 User Guide

2
8
D is assem bly s te p s
 In sp ectio n b efo re d is a sse m bly
( R efe r to P . 2 6-4 2.)
1 . C ove r
2 . B earin g c a p
 A
3. D if f e re ntia l c a se a sse m bly
4 . S id e b earin g s p ace r
5 . S id e b earin g o ute r r a ce
 B
6. S id e b earin g in ner r a ce
 C
7. D riv e g ear
 D
8. Lock p in
9 . P in io n s h aft
1 0. P in io n g ear
1 1 . P in io n w ash er
1 2. S id e g ear
1 3. S id e g ear s p ace r
1 4. D if f e re ntia l c a se
 E
15. S elf - lo ckin g n ut
1 6. W ash er
 F
17. D riv e p in io n a sse m bly 1
8. D riv e p in io n
1 9. D riv e p in io n fr o nt s h im ( fo r p in io n
h eig ht a dju stm ent)
 G
20. D riv e p in io n fr o nt b earin g in ner
r a ce
2 1. D riv e p in io n s p ace r
2 2. D riv e p in io n r e ar s h im ( fo r tu rn in g
t o rq ue a dju stm ent)
2 3. C om panio n fla nge
2 4. O il s e al
2 5. D riv e p in io n r e ar b earin g in ner r a ce
 H
26. D riv e p in io n r e ar b earin g o ute r
r a ce
 I
27. D riv e p in io n fr o nt b earin g o ute r
r a ce
2 8. O il s e al
2 9. G ear c a rrie r
3 0. P lu g c o ve r
3 1. Vent p lu g

REAR AXLE ± General Information27-2
GENERAL INFORMATION27100010118

The rear axle is a banjo-type semi-floating type.
The axle shaft bearings are: *Single taper
bearings for vehicles without ABS or rear
differential lock. *Double-taper bearings for
vehicles with ABS or rear differential lock. ABS
rotor is press-fitted to the axle shaft retainer
ring.
Differential gear has 4 different types. A
torque-responsive mechanical-type limited slip
differential has a high performance against
driving on unstable surfaces such as muddy
roads.

Driveability on sand or muddy road has been
improved, and rear differential lock, which is
useful for emergency , has been used.
REAR AXLE
ItemVehicles without rear differential lockVehicles with rear differential lock
Axle housing typeBanjo typeBanjo type
Axle
shaft
Support methodSemi-floating typeSemi-floating type
shaft
Shaft O.D. (Bearing part x
Centre x Length) mm40.0 x 34.5 x 744.540.0 x 34.5 x 723.5 (LH)
40.0 x 34.5 x 761.0 (RH)
Bearing typeSingle taper (double taper)*Double taper
Bearing (O.D. x I.D.) mm80.0 x 40.080.0 x 40.0
NOTE
*: Vehicles with ABS.
DIFFERENTIAL
<2WD>
Item4G634D56
Drive gear typeHypoid gearHypoid gear
Reduction ratio4.6364.222
Limited slip differential typeTorque sensitivity type mechanicalTorque sensitivity type mechanical
Differential gear type
(type x quantity)
Side gearStraight bevel gear x 2Straight bevel gear x 2
(ty e x quantity)
Pinion gearStraight bevel gear x 2 [Straight bevel
gear x 4]Straight bevel gear x 2 [Straight bevel
gear x 4]
Number of teethSide gear5138
Drive pinion119
Side gear1414
Pinion gear1010
Bearing (O.D. x I.D.)
mm
Side80.0 x 45.280.0 x 45.2
mm
Front68.3 x 30.268.3 x 30.2
Rear76.2 x 36.576.2 x 36.5
NOTE
[ ]: Vehicles with limited slip differential

REAR AXLE ± Service Specifications27-4
SERVICE SPECIFICATIONS27100030121
ItemStandard valueLimit
Rear axle total backlash mm±5
Axle shaft axial play mmVehicles without ABS or rear differential lock0.05 ± 0.20±
Vehicles with ABS or rear differential lock0 ± 0.25±
Limited slip differential
p
reload Nm
Using special tool13 or more±
reload Nm
Without using special tool25 or more±
Axle shaft retainer
press-fitting force NVehicles without ABS or rear differential lockInitial press-fitting force
49,000 or more±
Final press-fitting force
78,000±
Vehicles with ABS or rear differential lockInitial press-fitting force
49,000 or more±
Final press-fitting force
98,000 ± 108,000±
Clearance between axle shaft retainer and snap ring mm0 ± 0.166±
Rear differential lock air pump pressure kPa25 ± 40±
Drive gear backlash mm2WD0.08 ± 0.13±
4WD0.13 ± 0.18±
Drive gear runout mm±0.05
Differential gear backlash mm2WD0 ± 0.250.2
4WD0 ± 0.0760.2
Limited slip differential
starting torque Nm
When a new clutch plate is used39 ± 74±
starting torque Nm
When re-installing current clutch plate25 ± 74±
Drive pinion
turning torque NmWithout oil sealWhen replacing
(with anti-rust agent)0.6 ± 0.9±
When replacing or reusing
(with gear oil applied)0.4 ± 0.5±
With oil sealWhen replacing
(with anti-rust agent)0.8 ± 1.1±
When replacing or
reusing (with gear oil applied)0.6 ± 0.7±

REAR AXLE ± Service Specifications/Lubricants/Sealants27-5
ItemStandard valueLimit
Horizontal difference between friction plate and friction disc thickness mm0 ± 0.05±
Clearance between friction plate and friction disc mm0.06 ± 0.20±
Clearance in side gear axial direction mm0.05 ± 0.20±
Difference between left and right dimensions from back thrust face of pressure
ring to end of thrust washer mm0 ± 0.05±
Friction plate and friction disc warping (flatness) mm±0.08
Friction plate and friction disc wear
(difference in the thickness of the friction surface and the projections) mm±0.1
LUBRICANTS27100040049
ItemSpecified lubricantsQuantity
Rear differential gear oil
Conventional differential:
Hypoid gear oil
API classification GL-5 or higher SAE viscosity No. 90,
80 W

Limited slipdifferential:
2WD1.6


Limited sli differential:
Hypoid gear oil
MITSUBISHI Genuine Gear Oil Part No. 8149630 EX
CASTROL HYPOY LS (GL-5, SAE 90), SHELL-LSD
(GL-5, SAE 80W-90) or equivalent4WD2.6

SEALANTS27100050042
ItemsSpecified sealantsRemarks
Bearing case3M ATD Part No. 8661 or equivalentSemi-drying sealant
Dust cover
Axle housing (differential carrier mounting part)
Drive gear and differential case mounting part3M Stud Locking 4170 or equivalentAnaerobic sealant

1
8 <
C onven tio nal d if fe re n tia l>
< L im it e d s lip d if fe re n tia l>
1
7
25 2
7 3
2
0
21 2
2 23 24
2
9
11
1
2
13 1
4
1
2 1
5
6
7
16
65 2
1
2
5
6
1
5
5
614
13
10
9
11
12
8 7
1 9
2
1
3
3 0
2 8
2 6
4 4
D is assem bly s te p s
 In sp ectio n b efo re d is a sse m bly
( P .2 7-3 0.)
1 . Lock p la te
 A
2. S id e b earin g n ut
3 . B earin g c a p
 B
4. D if f e re ntia l c a se a sse m bly
5 . S id e b earin g o ute r r a ce
 C
6. S id e b earin g in ner r a ce
 D
7. D riv e g ear
 E
8. Lock p in
9 . P in io n s h aft
1 0. Thru st b lo ck < V ehic le s w it h out A BS>
1 1 . P in io n g ear
1 2. P in io n w ash er
1 3. S id e g ear
1 4. S id e g ear th ru st s p ace r
1 5. D if f e re ntia l c a se 1
6. Lim it e d s lip d if f e re ntia l c a se a sse m bly
 F
17. S elf - lo ckin g n ut
1 8. W ash er
 G
19. D riv e p in io n a sse m bly
2 0. D riv e p in io n fr o nt s h im ( F or a dju stin g
p re lo ad o f d riv e p in io n)
2 1. D riv e p in io n s p ace r
 H
22. D riv e p in io n r e ar b earin g in ner r a ce
2 3. D riv e p in io n r e ar s h im ( F or a dju stin g
d riv e p in io n h eig ht)
2 4. D riv e p in io n
2 5. C om panio n fla nge
 I
26. O il s e al
 I
27. D riv e p in io n fr o nt b earin g in ner r a ce
 I
28. D riv e p in io n fr o nt b earin g o ute r r a ce
 J
29. D riv e p in io n r e ar b earin g o ute r r a ce
3 0. D if f e re ntia l c a rrie r

ABS <2WD> ± Troubleshooting35B-7
INSPECTION PROCEDURE FOR DIAGNOSIS CODES
Code No. 11, 12, 13, 14 Wheel speed sensor open circuit
or short circuitProbable cause
Code No. 21, 22, 23, 24 Wheel speed sensor abnormal
The ABS-ECU determines that an open circuit or short circuit occurs in more than
one line of wheel speed sensors.
Malfunction of wheel speed sensor

Malfunction of wiring harness or connector

Malfunction of ABS-ECU
These codes are output at the following times:

When an open circuit cannot be found, but more than one wheel speed sensor
does not output any signal during driving at 8 km/h or higher.

When a chipped or plugged-up rotor tooth, etc. is detected.

When the sensor output drops and anti-lock control is continuously carried out
due to a defective sensor or a warped rotor.
Malfunction of wheel speed sensor

Malfunction of rotor

Malfunction of wheel bearing

Malfunction of wiring harness or connector

Malfunction of ABS-ECU
NG
Replace the ABS-ECU.
OK
Check trouble symptoms.
OK
Check the following connector.
C-62NG
RepairOK
Wheel bearing check. (Refer to GROUP
26 and 27 ± On-vehicle Service.)
OK
Rotor check. (Refer to P.35B-40.)NGReplace the rotor.
OK
Wheel speed sensor output voltage
check. (Refer to P.35B-24.)NGWheel speed sensor check. (Refer to
P.35B-39.)NGReplace the wheel speed sensor.
OK
Measure at the ABS-ECU connectors
C-62

Disconnect the connector and
measure from the harness side.

Resistance values between 10 ± 23,
7 ± 20, 8 ± 21 and 9 ± 22.
OK: 1.2 ± 1.4 kWNGCheck the following connectors.
A-01, A-07, F-01, F-16, D-01 and C-02NG
Repair
Wheel speed sensor installation check.NG
Repair
OK
Check trouble symptoms.NGCheck the harness wire between each
wheel speed sensor and ABS-ECU, and
repair if necessary.

ABS <2WD> ± Troubleshooting35B-14
INSPECTION CHART FOR TROUBLE SYMPTOMS35201140142
Get an understanding of the trouble symptoms and check according to the inspection procedure chart.
Trouble symptomsInspection
procedure No.Reference
page
Communication with MUT-II
is notpossible
Communication with all systems is not possible.135B-15
is not ossible.
Communication with ABS only is not possible.235B-15
When the ignition key is turned to ªONº (engine stopped), the ABS warning lamp does
not illuminate.335B-16
After the engine starts, the ABS warning lamp remains illuminated.435B-16
When the ignition key is turned to ªSTARTº, the ABS warning lamp does not illuminate.535B-17
After the ignition key is turned to ªONº, the ABS warning lamp blinks twice, and when
turned to ªSTARTº, it illuminates. When returned to ªONº, the lamp flashes once, and
then switches off.635B-17
Faulty ABS operationUnequal braking power on both sides735B-18
Insufficient braking power
ABS operates under normal braking conditions
ABS operates before vehicle stops under normal
braking conditions
Large brake pedal vibration (Caution 2.)±±
Caution
1. If steering movements are made when driving at high speed, or when driving on road surfaces
with low frictional resistance, or when passing over bumps, the ABS may operate even though
sudden braking is not being applied. Because of this, when getting information from the customer,
check if the problem occurred while driving under such conditions as these.
2. During ABS operation, the brake pedal may vibrate or may not be able to be depressed. Such
phenomena are due to intermittent changes in hydraulic pressure inside the brake line to prevent
the wheels from locking and is not an abnormality.

ABS <4WD> ± Troubleshooting35C-6
INSPECTION CHART FOR DIAGNOSIS CODES35201130163
Inspect according to the inspection chart that is appropriate for the malfunction code.
Diagnosis
code No.Inspection itemDiagnosis contentReference page
11Front right wheel speed sensorOpen or short circuitRefer to GROUP 35B ± Troubleshooting.
12Front left wheel speed sensor
13Rear right wheel speed sensor
14Rear left wheel speed sensor
15Wheel speed sensorAbnormal output signalRefer to GROUP 35B ± Troubleshooting.
16Power supply systemRefer to GROUP 35B ± Troubleshooting.
21Front right wheel speed sensorAbnormalRefer to GROUP 35B ± Troubleshooting.
22Front left wheel speed sensor
23Rear right wheel speed sensor
24Rear left wheel speed sensor
25Free wheel engage switch35C-7
264WD position detection switch35C-8
27Rear differential lock detection switch35C-9
32G-sensor system35C-10
33Stop lamp switch systemRefer to GROUP 35B ± Troubleshooting.
41Front right solenoid valveRefer to GROUP 35B ± Troubleshooting.
42Front left solenoid valve
43Rear solenoid valve
51Valve relayRefer to GROUP 35B ± Troubleshooting.
53Motor relay, motorRefer to GROUP 35B ± Troubleshooting.
63ABS-ECURefer to GROUP 35B ± ABS-ECU.
(Replace the ABS-ECU )
64
(Re lace the ABS-ECU.)

ABS <4WD> ± Troubleshooting35C-9
Code No. 27 Rear differential lock detection switch
Probable cause
The ABS-ECU determines that an open circuit occurs in rear differential detection
switch system.
Malfunction of wiring harness or connector

Malfunction of rear differential lock-ECU

Malfunction of ABS-ECU
Does the 4WD indicator lamp (rear dif-
ferential lamp) operate normally?NoRear differential lock-ECU check.NGReplace the rear differential lock-ECU.
Ye s
Measure at the ABS-ECU connector
C-64.

Disconnect the connector and
measure at the harness side.

Ignition switch: ON

Rear differential lock switch: OFF

Voltage between 46 and body earth
OK:System voltageNGCheck the following connectors.
C-88, C-86, C-02 and C-64NG
Repair
OK
Check trouble symptom.NGCheck the harness between rear differ-
ential detection switch and the ABS-
ECU, and repair if necessary.
OK
Check the following connector.
C-64NG
Repair
OK
Check trouble symptoms.NGReplace the ABS-ECU.
Code No. 27 Rear differential lock detection switch
Probable cause
For vehicles without rear differential lock, battery positive voltage is applied to the
ABS-ECU terminal No. 46.
This code is output when this line is interrupted.
Malfunction of wiring harness or connector

Malfunction of ABS-ECU
Is the fuse No. 7 normal?NoReplace the fuse after eliminating the
cause of the blowout.
Ye s
Measure at the ABS-ECU connector
C-64.

Disconnect the connector and
measure at the harness side.

Ignition switch ON

Voltage between 46 and body earth
OK:System voltageNGCheck the following connectors.
C-88, C-86, C-02 and C-64NG
Repair
OK
Check trouble symptoms.NGCheck the harness between fuse No.
7 inside the junction block and the ABS-
ECU, and repair if necessary.
OK
Check the following connector.
C-64NG
Repair
OK
Check trouble symptoms.NGReplace the ABS-ECU.

ABS <4WD> ± Troubleshooting35C-11
DATA LIST REFERENCE TABLE35201150107
The following items can be read by the MUT-II from the ABS-ECU input data.
1. When the system is normal
Item No.Check itemChecking requirementsNormal value
11Front-right wheel speed sensorPerform a test runVehicle speeds
displayed on the12Front-left wheel speed sensor
dis layed on the
speedometer
and MUTIIare13Rear-right wheel speed sensorand MUT-II are
identical.
14Rear-left wheel speed sensor
16ABS-ECU power supply
voltageIgnition switch power supply voltage and valve
monitor voltage9 ± 16 V
25Free wheel engage switchEngage 4WDON
Engage 2WDOFF
264WD detection switchPlace the transfer lever at 4H.ON
Place the transfer lever at 2H.OFF
27Rear differential lock detection
switch
Turn on the switch.ON
switch
Turn off the switch.OFF
32G-sensor output voltageStop the vehicle.2.4 ± 2.6 V
Perform a test run.Display value
fluctuates with a
mean value of
2.5 V.
33Stop lamp switchDepress the brake pedal.ON
Release the brake pedal.OFF
2. When the ABS-ECU shut off ABS operation.
When the diagnosis system stops the ABS-ECU, the MUT-II display data will be unreliable.
ACTUATOR TEST INSPECTION TABLE35201160056
Refer to GROUP 35B ± Troubleshooting.