oil temperature MITSUBISHI TRITON 1997 User Guide

SRS ± SRS Diagnosis Unit (SDU)/Air Bag Module and Clock Spring52B-28
INSPECTION52400220093

Check the SDU and brackets for dents, cracks or
deformation.

Check connector for damage, and terminals for
deformation.
Caution
If a dent, crack, deformation or rust is discovered,
replace the SDU with a new one.
NOTE
For checking of the SDU other than described above,
refer to the section concerning troubleshooting. (Refer
to P.52B-6.)
AIR BAG MODULE AND CLOCK SPRING52400240143
Caution
1. Disconnect the battery (±) terminal and wait
for 60 seconds or more before starting work.
Furthermore, the disconnected battery
terminal should be covered with tape to
insulate it. (Refer to P.52B-3, No.4.)
2. Never attempt to disassemble or repair the
air bag modules or clock spring.
If faulty, replace it.
3. Do not drop the air bag modules or clock
spring or allow contact with water, grease
or oil.
Replace it if a dent, crack, deformation or
rust is detected.4. The air bag modules should be stored on
a flat surface and placed so that the pad
surface is facing upward.
Do not place anything on top of it.
5. Do not expose the air bag modules to
temperatures over 93C.
6. After deployment of an air bag, replace the
clock spring with a new one.
7. Wear gloves and safety glasses when
handling air bags that have already
deployed.
8. An undeployed air bag module should only
be disposed of in accordance with the
procedures (Refer to P.52B-34.)

± General Information HEATER, AIR CONDITIONER
AND VENTILATION55-3
GENERAL INFORMATION55200010121
The heater system uses a two-way-flow full-air-mix
system that features high performance and low
operating noise, and includes an independent face
air blowing function and a cool air bypass function.The A/C system is basically the same as the
conventional system, but a new refrigerant system
has been adopted as a response to restrictions
on the use of chlorofluorocarbons.
ItemsSpecifications
Heater unitTypeTwo-way-flow full-air-mix system
Heater control assemblyDial type
CompressorModelInclined-plate type
Dual pressure switch
kPa
High-pressure switchON
OFF: 2,648, OF
F ON: 2,059
kPa
Low-pressure switchON
OFF: 177, OFF
ON: 186
Refrigerant and quantity gR-134a (HFC-134a), Approx. 550 ± 600
SAFETY PRECAUTIONS
Because R-134a refrigerant is a hydrofluorocarbon
(HFC) which contains hydrogen atoms in place of
chlorine atoms, it will not cause damage to the
ozone layer.
Refrigerant R-134a is transparent and colourless
in both the liquid and vapour state. Since it has
a boiling point of ± 29.8
C, at atmospheric pressure,
it will be a vapour at all normal temperatures and
pressures. The vapour is heavier than air,
non-flammable, and nonexplosive. The following
precautions must be observed when handling
R-134a.Caution
Wear safety goggles when servicing the
refrigeration system.
R-134a evaporates so rapidly at normal
atmospheric pressures and temperatures that it
tends to freeze anything it contacts. For this reason,
extreme care must be taken to prevent any liquid
refrigerant from contacting the skin and especially
the eyes. Always wear safety goggles when
servicing the refrigeration part of the A/C system.
Keep a bottle of sterile mineral oil handy when
working on the refrigeration system. Should any
liquid refrigerant get into the eyes, use a few drops
of mineral oil to wash them out. R-134a is rapidly
absorbed by the oil. Next splash the eyes with
plenty of cold water. Call your doctor immediately
even though irritation has ceased after treatment.

2
INSPECTION
· Check the SRS-ECU and brackets for dents, cracks or
deformation.
· Check connectors and lock lever for damage, and
terminals for deformation
Caution
If a dent, crack, deformation or rust is discovered,
replace the SRS-ECU with a new one.
NOTE
For checking of the SRS-ECU other than described
above, refer to the section concerning troubleshooting.
(Refer to P.52B-5.)
AIR BAG MODULES AND CLOCK SPRING
Caution
1. Disconnect the battery (-) terminal and wait
for 60 seconds or more before starting
work. Furthermore, the disconnected
battery terminal should be covered with
tape to insulate it. (Refer to P.52B-3)
2. Never attempt to disassemble or repair the
air bag modules or clock spring.
If faulty, replace it.
3. do not drop the air bag modules or clock
spring or allow contact with water, grease
or oil.
Replace it if a dent, crack, deformation or
rust is detected.4. The air bag modules should be stored on a
flat surface and placed so that the pad
surface is facing upward.
Do not place anything on top of it.
5. Do not expose the air bag modules to
temperatures over 93° C.
6. After deployment of an air bag, replace the
clock spring with a new one.
7. Wear gloves and safety glasses when
handling air bags that have already
deployed.
8. An undeployed air bag module should only
be disposed of in accordance with the
procedures (Refer to P.52B-31.)
52B-22SRS - SRS-ECU/Air Bag Modules and Clock Spring
52400220031
After deployment of an air bag, replace the
air bag modules. Check the clock spring,
and if faulty, replace it with a new part.
52400240044

4
INSPECTION
· Check the SDU and brackets for dents, cracks or
deformation.
· Check connector for damage, and terminals for
deformation
Caution
If a dent, crack, deformation or rust is discovered,
replace the SDU with a new one.
NOTE
For checking of the SDU other than described above,
refer to the section concerning troubleshooting. (Refer to
P.52B-6.)
AIR BAG MODULES AND CLOCK SPRING
Caution
1. Disconnect the battery (-) terminal and wait
for 60 seconds or more before starting
work. Furthermore, the disconnected
battery terminal should be covered with
tape to insulate it. (Refer to P.52B-3)
2. Never attempt to disassemble or repair the
air bag modules or clock spring.
If faulty, replace it.
3. do not drop the air bag modules or clock
spring or allow contact with water, grease
or oil.
4. Replace it if a dent, crack, deformation or
rust is detected.
4. The air bag modules should be stored on a
flat surface and placed so that the pad
surface is facing upward.
Do not place anything on top of it.
5. Do not expose the air bag modules to
temperatures over 93° C.
6. After deployment of an air bag, replace the
clock spring with a new one.
7. Wear gloves and safety glasses when
handling air bags that have already
deployed.
8. An undeployed air bag module should only
be disposed of in accordance with the
procedures (Refer to P.52B-31.)
52B-28SRS - SRS Diagnosis Unit (SDU)/Air Bag Modules and Clock Spring
52400220093
After deployment of an air bag, replace the
air bag modules. Check the clock spring, and
if faulty, replace it with a new part.

52400240143