wheel MITSUBISHI TRITON 1997 User Guide

REAR SUSPENSION ± On-vehicle Service34-3
ON-VEHICLE SERVICE34101100034
REAR WHEEL ALIGNMENT
The rear suspension assembly must be free of worn, loose
or damaged parts prior to measurement of rear wheel
alignment.
Standard value:
Toe-in 0 mm
Camber 0

NOTE
Toe-in and camber are set at the factory and cannot be
adjusted. If toe-in or camber is not within the standard value,
check and replace bent or damaged parts.

BASIC BRAKE SYSTEM ± General Information35A-3
GENERAL INFORMATION35100010120
The brake system has high reliability and durability
which maintains excellent braking performance and
braking feeling. The main features are as follows.

A dual type master cylinder is equipped in all
models.

Both a single type and a tandem type brake
booster have been adopted.
The following type of brake have been adopted.
Front: Floating caliper, 2-piston, ventilated disc
brakes (V4-W43, V5-W43) or floating caliper,
1-piston, ventilated disc brakes (V4-S60,
V5-S60)
Rear: Leading-trailing type drum brake.
Items2WD
vehicles>2WD
vehicles>4WD
vehicles>4WD
vehicles>
Master cylinder I.D. mm23.823.823.823.8
Brake booster effective dia.
of power cylinder mm230
205 + 230*230
180 + 205*205 + 230180 + 205
Brake booster boosting ratio5.05.07.07.0
Load sensing proportioning
valve decompression ratio0.150.150.150.15
Front brake disc effective
dia. mm200200222
228*222
228*
Front brake wheel cylinder
I.D. mm60.3
42.9*60.3
42.9*60.3
42.9*60.3
42.9*
Rear drum brake drum I.D.
mm254254270270
Rear drum brake wheel
cylinder I.D. mm23.823.823.823.8
Rear drum brake lining
thickness mm4.74.74.74.7
NOTE
*: Vehicles with ABS.

BASIC BRAKE SYSTEM ± Service Specifications35A-5
SERVICE SPECIFICATIONS35100030119
ItemsStandard valueLimit
Brake pedal height mm176 ± 181±
Brake pedal free play mm3 ± 8±
Brake pedal to floor board clearance mm95 or more±
Load sensing proportioning
valve outputpressure kPa
2WDWhen load sensing
spring length is 190
3,625 (5,884)±
valve out ut ressure kPa
(Input pressure kPa)
s ring length is 190
mm (when unladen)5,390 (17,652)±
When load sensing
spring length is 215
mm (when laden)14,393 (17,652)±
4WDWhen load sensing
spring length is 190
4,309 (5,884)±
s ring length is 190
mm (when unladen)6,074 (17,652)±
When load sensing
spring length is 215
mm (when laden)16,310 (17,652)±
Load sensing spring length mm189 ± 193±
Booster push rod to master
cylinder piston clearance mmSingle brake boosterPetrol-powered ve-
hicles0.65 ± 1.05±
Diesel-powered ve-
hicles1.00 ± 1.40±
Tandem brake boosterVehicle which brake
booster of power
cylinder is 180 mm
and 205 mm in
effective diameter0.90 ± 1.30±
Vehicle which brake
booster of power
cylinder is 205 mm
and 230 mm in
effective diameter0.70 ± 1.10±
Front disc brake pad thickness mm102.0
Front brake disc thickness mm2422.4
Front brake disc run-out mm2WD±0.08
4WD±0,06
Front disc brake drag force (tangential force of wheel mounting bolts) N69 or less±
Rear drum brake lining thickness mm4.71.0
Rear drum inside diameter mm2WD254.0256.0
4WD270.0272.0
Front hub end play mm0.05±

BASIC BRAKE SYSTEM ± Troubleshooting35A-8
SymptomProbable causeRemedy
Insufficient parking brake functionWorn brake lining or padReplace
Grease or oil on lining or pad surface
Parking brake cable sticking
Stuck wheel cylinder or caliper piston
Excessive parking brake lever strokeAdjust the parking brake lever stroke or
check the parking brake cable routing
Auto adjuster malfunctionAdjust
Scraping or grinding noise when
brakes are applied
Worn brake lining or padReplace
brakes are a lied
Caliper to wheel interferenceCorrect or replace
Dust cover to disc interference
Bent brake backing plate
Cracked drums or brake disc
Squealing, groaning or chattering
noise when brakes are appliedDisc brakes ± Missing or damaged
brake pad anti-squeak shimReplace
Brake drums and linings, discs and pads
worn or scoredCorrect or replace
Improper lining parts
Disc brake ± Burred or rusted calipersCorrect or deburr
Dirty, greased, contaminated or glazed
liningsClean or replace
Drum brakes ± Weak, damaged or
incorrect shoe hold-down springs, loose
or damaged shoe hold-down pins and
springsCorrect or replace
Incorrect brake pedal or booster push rodAdjust

BASIC BRAKE SYSTEM ± Troubleshooting35A-9
SymptomProbable causeRemedy
Squealing noise
when brakes are
Bent or warped backing plate causing interference with drumReplace
when brakes are
not appliedDrum brakes ± Weak, damaged or incorrect shoe-to-shoe
spring
Poor return of brake booster, master cylinder or wheel
cylinder
Loose or extra parts in brakesRetighten
Improper positioning of pads in caliperCorrect
Improper installation of support mounting to caliper body
Improper machining of drum causing interference with
backing plate or shoeReplace drum
Disc brakes ± Rusted, stuckLubricate or replace
Worn, damaged or insufficiently lubricated wheel bearings
Incorrect brake pedal or booster push rodAdjust
Groaning, clicking or
rattling noise when
Stones or foreign material trapped inside wheel coversRemove stones, etc.
rattling noise when
brakes are not appliedLoose wheel nutsRetighten
Disc brakes ± Loose installation bolts
Worn, damaged or dry wheel bearingsLubricate or replace
Disc brakes ± Failure of shimReplace
Disc brakes ± Wear on sleeve
Incorrect brake pedal or booster push rodAdjust

35B-2
Bleeding 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Fluid Level Sensor Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Sensing Spring Length Check and
Adjustment Refer to GROUP 35A. . . . . . . . . . . . . . .
Load Sensing Proportioning Valve Function
Test Refer to GROUP 35A. . . . . . . . . . . . . . . . . . . . .
Disc Brake Pad Check and Replacement 23. . . . .
Front Disc Brake Rotor Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lining Thickness Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Drum Inside Diameter Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lining and Brake Drum Connection Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Speed Sensor Output Voltage Check
24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Unit Check 26. . . . . . . . . . . . . . . . . . . . . . . .
Solenoid Valve Check 27. . . . . . . . . . . . . . . . . . . . . . .
Motor Operation Check 27. . . . . . . . . . . . . . . . . . . . . . Motor Relay and Valve Relay Continuity
Check 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remedy for a Flat Battery 28. . . . . . . . . . . . . . . . . . .
BRAKE PEDAL Refer to GROUP 35A. . . . . . . .
MASTER CYLINDER AND BRAKE
BOOSTER 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOAD SENSING PROPORTIONING VALVE
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . .
FRONT DISC BRAKE 32. . . . . . . . . . . . . . . . . . . . .
REAR DRUM BRAKE
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . .
HYDRAULIC UNIT 37. . . . . . . . . . . . . . . . . . . . . . . . .
WHEEL SPEED SENSOR 39. . . . . . . . . . . . . . . . . .
ABS-ECU 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ABS <2WD> ± Troubleshooting35B-6
INSPECTION CHART FOR DIAGNOSIS CODES35201130156
Inspect according to the inspection chart that is appropriate for the malfunction code.
Diagnosis
code No.Inspection itemDiagnosis contentReference page
11Front right wheel speed sensorOpen or short circuit35B-7
12Front left wheel speed sensor
13Rear right wheel speed sensor
14Rear left wheel speed sensor
15Wheel speed sensorAbnormal output signal35B-8
16Power supply system35B-8
21Front right wheel speed sensorAbnormal35B-7
22Front left wheel speed sensor
23Rear right wheel speed sensor
24Rear left wheel speed sensor
33Stop lamp switch system35B-9
41Front right solenoid valve35B-10
42Front left solenoid valve
43Rear solenoid valve
51Valve relay35B-11
53Motor relay, motor35B-12
63ABS-ECU35B-41
(Replace the ABS-ECU)
64
(Re lace the ABS-ECU)

ABS <2WD> ± Troubleshooting35B-7
INSPECTION PROCEDURE FOR DIAGNOSIS CODES
Code No. 11, 12, 13, 14 Wheel speed sensor open circuit
or short circuitProbable cause
Code No. 21, 22, 23, 24 Wheel speed sensor abnormal
The ABS-ECU determines that an open circuit or short circuit occurs in more than
one line of wheel speed sensors.
Malfunction of wheel speed sensor

Malfunction of wiring harness or connector

Malfunction of ABS-ECU
These codes are output at the following times:

When an open circuit cannot be found, but more than one wheel speed sensor
does not output any signal during driving at 8 km/h or higher.

When a chipped or plugged-up rotor tooth, etc. is detected.

When the sensor output drops and anti-lock control is continuously carried out
due to a defective sensor or a warped rotor.
Malfunction of wheel speed sensor

Malfunction of rotor

Malfunction of wheel bearing

Malfunction of wiring harness or connector

Malfunction of ABS-ECU
NG
Replace the ABS-ECU.
OK
Check trouble symptoms.
OK
Check the following connector.
C-62NG
RepairOK
Wheel bearing check. (Refer to GROUP
26 and 27 ± On-vehicle Service.)
OK
Rotor check. (Refer to P.35B-40.)NGReplace the rotor.
OK
Wheel speed sensor output voltage
check. (Refer to P.35B-24.)NGWheel speed sensor check. (Refer to
P.35B-39.)NGReplace the wheel speed sensor.
OK
Measure at the ABS-ECU connectors
C-62

Disconnect the connector and
measure from the harness side.

Resistance values between 10 ± 23,
7 ± 20, 8 ± 21 and 9 ± 22.
OK: 1.2 ± 1.4 kWNGCheck the following connectors.
A-01, A-07, F-01, F-16, D-01 and C-02NG
Repair
Wheel speed sensor installation check.NG
Repair
OK
Check trouble symptoms.NGCheck the harness wire between each
wheel speed sensor and ABS-ECU, and
repair if necessary.

ABS <2WD> ± Troubleshooting35B-8
Code No. 15 Wheel speed sensor (Abnormal output signal)Probable cause
A wheel speed sensor outputs an abnormal signal (other than an open or short-circuit).
Improper installation of wheel speed sensor

Malfunction of wheel speed sensor

Malfunction of rotor

Malfunction of wheel bearing

Malfunction of wiring harness or connector

Malfunction of ABS-ECU
NG
Replace the ABS-ECU.
OK
Check trouble symptoms.
OK
Wheel bearing check. (Refer to GROUP
26 and 27 ± On-vehicle Service.)OKCheck the harness wire between each
wheel speed sensor and ABS-ECU, and
repair if necessary.
OK
Rotor check. (Refer to P.35B-40.)NGReplace the rotor.
OK
Check the following connector.
C-62NG
Repair
OK
Wheel speed sensor output voltage
check (Refer to P.35B-24.)NGWheel speed sensor check. (Refer to
P.35B-39.)NGReplace the wheel speed sensor.
Wheel speed sensor installation check.NG
Repair
Code No. 16 Power supply systemProbable cause
The voltage of the ABS-ECU power supply drops lower or rises higher than the specified
value. If the voltage returns to the specified value, this code is no longer output.
Malfunction of wiring harness or connector.

Malfunction of ABS-ECU
Caution
If battery voltage drops or rises during inspection, this code will be output as well. If the voltage
returns to standard value, this code is no longer output.
Before carrying out the following inspection, check the battery level, and refill distilled water if
necessary.
OK
Check the battery.
OK
Check trouble symptoms.NGCheck the harnes wire between the igni-
tion switch and the ABS-ECU, and repair
if necessary.
OK
Check trouble symptoms.NGReplace the ABS-ECU.
OK
Check the following connector.
C-62NG
Repair
Measure at the ABS-ECU connector
C-62.

Disconnect the connector and
measure at the harness side.

Start the engine. Voltage between
13 ± Body earth
OK:System voltageNGCheck the following connectors.
C-88, C-86 and C-02NG
Repair

ABS <2WD> ± Troubleshooting35B-14
INSPECTION CHART FOR TROUBLE SYMPTOMS35201140142
Get an understanding of the trouble symptoms and check according to the inspection procedure chart.
Trouble symptomsInspection
procedure No.Reference
page
Communication with MUT-II
is notpossible
Communication with all systems is not possible.135B-15
is not ossible.
Communication with ABS only is not possible.235B-15
When the ignition key is turned to ªONº (engine stopped), the ABS warning lamp does
not illuminate.335B-16
After the engine starts, the ABS warning lamp remains illuminated.435B-16
When the ignition key is turned to ªSTARTº, the ABS warning lamp does not illuminate.535B-17
After the ignition key is turned to ªONº, the ABS warning lamp blinks twice, and when
turned to ªSTARTº, it illuminates. When returned to ªONº, the lamp flashes once, and
then switches off.635B-17
Faulty ABS operationUnequal braking power on both sides735B-18
Insufficient braking power
ABS operates under normal braking conditions
ABS operates before vehicle stops under normal
braking conditions
Large brake pedal vibration (Caution 2.)±±
Caution
1. If steering movements are made when driving at high speed, or when driving on road surfaces
with low frictional resistance, or when passing over bumps, the ABS may operate even though
sudden braking is not being applied. Because of this, when getting information from the customer,
check if the problem occurred while driving under such conditions as these.
2. During ABS operation, the brake pedal may vibrate or may not be able to be depressed. Such
phenomena are due to intermittent changes in hydraulic pressure inside the brake line to prevent
the wheels from locking and is not an abnormality.