air condition NISSAN 350Z 2007 Z33 Body, Lock And Security System User Guide

FUEL FILLER LID OPENER
BL-57
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
3. CHECK FUEL LID OPEN OUTPUT SIGNAL
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace BCM. Refer to BCS-17, "
Removal and Installation of BCM" .
4. CHECK FUEL LID OPENER ACTUATOR CIRCUIT
1. Disconnect BCM connector and fuel lid opener actuator connector.
2. Check continuity between BCM harness connector B83 terminal
70 and fuel lid opener actuator harness connector T19 terminal
1.
3. Check continuity between fuel lid opener actuator harness con-
nector T19 terminal 1 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK FUEL LID OPENER ACTUATOR GROUND CIRCUIT
Check continuity between fuel lid opener actuator harness connector
T19 terminal 2 and ground.
OK or NG
OK >> Replace fuel lid opener actuator.
NG >> Repair harness or connector.
ConnectorTerminal
(Wire color)
ConditionVoltage [V]
(Approx.)
(+) (–)
B83 70 (W/L) GroundFuel lid opener switch
ONBattery voltage
(for 0.5s)
Fuel lid opener switch
OFF0
PIIB1264E
70 (W/L) - 1 (W/L) : Continuity should exist.
1 (W/L) - ground : Continuity should not exist.
PIIB1265E
2 (B) - ground : Continuity should exist.
PIIA8090E

BL-58
FUEL FILLER LID OPENER
Revision: 2006 November2007 350Z
6. CHECK FUEL LID OPENER SWITCH
1. Disconnect fuel lid opener switch
2. Check continuity between fuel lid opener switch harness con-
nector M13 terminals 1 and 2.
OK or NG
OK >> GO TO 7.
NG >> Replace fuel lid opener switch.
7. CHECK FUEL LID OPENER SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector B83 terminal
58 and fuel lid opener switch harness connector M13 terminal 1.
3. Check continuity between BCM harness connector B83 terminal
58 (Y/B) and ground.
OK or NG
OK >> GO TO 8.
NG >> Repair harness or connector.
8. CHECK FUEL LID OPENERE SWITCH GROUND CIRCUIT
Check continuity between fuel lid opener switch harness connector
M13 terminal 2 and ground.
OK or NG
OK >> Replace fuel lid opener switch.
NG >> Repair harness or connector.
Connec-
torTerminalsFuel lid opener switch
conditionContinuity
M13 1 2ON (Pushed) Yes
OFF (Released) No
PIIA8091E
58 (Y/B) - 1 (L/R) : Continuity should exist.
58 (Y/B) - ground : Continuity should not exist.
PIIB3792E
2 (B) - ground : Continuity should exist.
PIIA8093E

BL-80
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2006 November2007 350Z
2. CHECK DOOR SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door switch and BCM connector.
3. Check continuity between door switch harness connector B17, B23 terminal 1 and BCM harness connec-
tor B83 terminal 62 (driver side) or M90 terminal 12 (passenger side).
4. Check continuity between door switch harness connector B17,
B23 terminal 1and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace door switch harness.
3. CHECK DOOR SWITCH
Check continuity between door switch B17 (driver side) or B23 (passenger side) terminal 1 and ground part of
door switch.
OK or NG
OK >> GO TO 4.
NG >> Replace door switch.Driver side door
1 (L) - 62 (L) : Continuity should exist.
Passenger side door
1 (P) - 12 (P) : Continuity should exist.
Driver side door
switch
1 (L) - Ground : Continuity should not exist.
Passenger side door
switch
1(P) - Ground : Continuity should not exist.
PIIA9540E
TerminalCondition of door
switchContinuity
1 Ground part of door switchPushed (close) No
Released (open) Yes
PIIA3351E

BL-82
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2006 November2007 350Z
2. CHECK DOOR SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect back door switch and BCM connector.
3. Check continuity between BCM harness connector B83 terminal 58 and back door switch harness con-
nector T12 terminal 1.
4. Check continuity between BCM harness connector B83 terminal
58 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace back door switch harness.
3. CHECK BACK DOOR SWITCH
Check continuity between back door switch terminals 1 and 3.
OK or NG
OK >> GO TO 4.
NG >> Replace back door switch.
4. CHECK BACK DOOR SWITCH GROUND CIRCUIT
Check continuity between door switch harness connector T12 terminal 3 and ground.
OK or NG
OK >> Check harness connection.
NG >> Repair or replace back door switch harness.58 (R/W) - 1 (R/W) : Continuity should exist.
58 (R/W) - Ground : Continuity should not exist.
PIIB3794E
Connector Terminal Condition of back door switch Continuity
T12 1 3Open position Yes
Closed position No
PIIA4316E
3 (B) - Ground : Continuity should exist.
PIIA2490E

REMOTE KEYLESS ENTRY SYSTEM
BL-83
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Check Trunk Lid Lock Assembly (Trunk Room Lamp Switch) / For RoadsterNIS0001N
1. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) INPUT SIGNAL
With CONSULT-III
Check trunk lid opener switch (“TRUNK OPN MNTR”) in “DATA MONITOR” mode with CONSULT-III.
Without CONSULT-III
Check voltage between BCM connector and ground.
*: When interior lamp battery saver control is in OFF. → Approx. 5V.
OK or NG
OK >> Trunk room lamp switch is OK.
NG >> GO TO 2.
2. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly (trunk room lamp switch) and BCM connector.
3. Check continuity between BCM harness connector B83 terminal 57 and trunk lid lock assembly (trunk
room lamp switch) harness connector T47 terminal 3.
4. Check continuity between BCM harness connector B83 terminal
57 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace trunk lid lock assembly (trunk room
lamp switch) harness.
Monitor item Condition
TRNK OPN MNTROPEN : ON
CLOSE : OFF
Con-
nectorTe r m i n a l s
(Wire color)Condition of trunk lid lock
assembly (trunk room lamp
switch)Voltage [V]
(Approx.)
(+) (–)
B83 57 (R/W) GroundOpen 0
Close Battery voltage*
PIIB1266E
57 (R/W) - 3 (R/W) : Continuity should exist.
57 (R/W) - Ground : Continuity should not exist.
PIIB9170E

BL-84
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2006 November2007 350Z
3. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly (trunk room lamp switch) connector.
3. Check continuity between trunk lid lock assembly (trunk room lamp switch) connector T47 terminal 1 and
ground.
OK or NG
OK >> Check trunk lid lock assembly (trunk room lamp switch).
NG >> Repair or replace trunk lid lock assembly (trunk room
lamp switch) harness.
Check Key Switch NIS0001O
1. CHECK KEY SWITCH
Check continuity key switch terminals 1 and 2.
OK or NG
OK >> GO TO 3.
NG >> Replace key switch.
2. CHECK KEY SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M90 terminal
37 and key switch harness connector M25 terminal 1.
3. Check continuity between BCM harness connector M90 terminal
37 and ground.
OK or NG
OK >> Check the following.

10A fuse [No.21, located in the fuse block (J/B)]

Harness for open or short between key switch and fuse
NG >> Repair or replace harness.1 (B) - Ground : Continuity should exist.
PIIB9171E
Connector Terminals Condition of key switch Continuity
M25 1 2Inserted Yes
Removed No
PIIA2627E
37 (B/R) - 1 (B/R) : Continuity should exist.
37 (B/R) - Ground : Continuity should not exist.
PIIB1258E

REMOTE KEYLESS ENTRY SYSTEM
BL-85
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Check IPDM E/R Operation NIS0001P
1. CHECK IPDM E/R INPUT SIGNAL
Check voltage between IPDM E/R connector E9 terminal 51 and ground.
OK or NG
OK >> Replace IPDM E/R.
NG >> GO TO 2.
2. CHECK IPDM E/R CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and horn relay connector.
3. Check continuity between IPDM E/R harness connector E9 terminal 51 and horn relay harness connector
E21 terminal 1.
OK or NG
OK >> Check harness connection.
NG >> Repair or replace harness.
Check Remote Keyless Entry Receiver NIS0001Q
1. CHECK MULTI-REMOTE CONTROL RECEIVER INPUT VOLTAGE
1. Remove key from ignition key cylinder.
2. Check signal between remote keyless entry receiver connector and ground with oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.51 (G/B) – Ground : Battery voltage
PIIA6403E
1 (G/B) - 51(G/B) : Continuity should exist.
PIIA6404E
Con-
nectorTerminal
(Wire color)
Condition Signal
(Reference value)
(+) (–)
M78 4 (Y)Grou
ndKey is inserted in
IGN key cylinder 0
All door closed
PIIA2835E
OCC3881D

REMOTE KEYLESS ENTRY SYSTEM
BL-87
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
4. CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Connect remote keyless entry receiver connector.
2. Check signal BCM connector and ground with oscilloscope.
OK or NG
OK >> Replace BCM.
NG >> GO TO 5.
5. CHECK REMOTE KEYLESS ENTRY RECEIVER HARNESS
1. Disconnect remote keyless receiver and BCM connector.
2. Check continuity between remote keyless entry receiver connector M78 terminal 2 and BCM connector
M90 terminal 20.
3. Check continuity between remote keyless entry receiver connector M78 terminal 2 and ground.
OK or NG
OK >> Replace remote keyless entry receiver.
NG >> Repair or replace the harness.
Con-
nectorTerminal (Wire
color)
Condition Signal
(Reference value)
(+) (–)
M90 20 (L) GroundKey is inserted
in IGN key cylin-
der0
Waiting
(All door closed)
When signal is
received
(All door closed)
PIIA9632E
OCC3879D
OCC3880D
2 (L) - 20 (L) : Continuity should exist.
2 (L) - Ground : Continuity should not exist.
PIIA9633E

TRUNK LID OPENER
BL-121
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
4. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK LID OPENER ACTUATOR) CIRCUIT
1. Disconnect BCM connector and trunk lid lock assembly (trunk lid
opener actuator) connector.
2. Check continuity between BCM harness connector B83 terminal
68 and trunk lid lock assembly (trunk lid opener actuator) har-
ness connector T47 terminal 2.
3. Check continuity between BCM harness connector B83 terminal
68 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECKTRUNK LID LOCK ASSEMBLY (TRUNK LID OPENER ACTUATOR) GROUND CIRCUIT
Check continuity between trunk lid lock assembly (trunk lid opener
actuator) harness connector T47 terminal 1 and ground.
OK or NG
OK >> Replace trunk lid lock assembly (trunk lid opener actua-
tor).
NG >> Repair harness or connector.
6. CHECK TRUNK LID OPENER CANCEL SWITCH
1. Disconnect trunk lid opener cancel switch.
2. Check continuity between trunk lid opener cancel switch har-
ness connector B71 terminals 1 and 2.
OK or NG
OK >> GO TO 7.
NG >> Replace trunk lid opener cancel switch.68 (L/R) - 2 (L/R) : Continuity should exist.
68 (L/R) - ground : Continuity should not exist.
PIIB9175E
1 (B) - ground : Continuity should exist.
PIIB9171E
TerminalsTrunk lid opener cancel
switch conditionContinuity
12ON Yes
OFF No
PIIA7871E

BL-122
TRUNK LID OPENER
Revision: 2006 November2007 350Z
7. CHECK TRUNK LID OPENER SWITCH
1. Disconnect trunk lid opener switch
2. Check continuity between trunk lid opener switch harness con-
nector T103 terminals 1 and 2.
OK or NG
OK >> GO TO 8.
NG >> Replace trunk lid opener switch.
8. CHECK TRUNK LID OPENER CANCEL SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M90 terminal
30 and trunk lid opener cancel switch harness connector B71
terminal 1.
OK or NG
OK >> GO TO 9.
NG >> Repair harness or connector.
9. CHECK TRUNK LID OPENER SWITCH CIRCUIT
Check continuity between trunk lid opener cancel switch harness
connector B71 terminal 2 and trunk lid opener switch harness con-
nector T103 terminal 1.
OK or NG
OK >> GO TO 10.
NG >> Repair harness or connector.
10. CHECK DRIVER SIDE DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect driver side door lock actuator connector.
2. Check continuity between trunk lid opener switch harness con-
nector T103 terminal 2 and driver side door lock actuator switch
harness connector D11 terminal 2.
OK or NG
OK >> GO TO 11.
NG >> Repair harness or connector.
Te r m i n a l sTrunk lid opener switch
conditionContinuity
12ON (Pushed) Yes
OFF (Released) No
PIIA7872E
30 (P) - 1 (SB) : Continuity should exist.
PIIB1272E
2 (R/Y) - 1 (P) : Continuity should exist.
PIIA7874E
2 (G) - 2 (OR) : Continuity should exist.
PIIA7875E