service NISSAN 350Z 2007 Z33 Brake System Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 54, PDF Size: 1.91 MB
Page 1 of 54
BR-1
BRAKE SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION BR
A
B
BR
Revision: 2006 November2007 350Z
BRAKE SYSTEM
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Precautions for Procedures without Cowl Top Cover ..... 3
Precautions for Brake System .................................. 3
PREPARATION ........................................................... 5
Commercial Service Tools ........................................ 5
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 6
NVH Troubleshooting Chart ..................................... 6
BRAKE PEDAL .......................................................... 7
Inspection and Adjustment ....................................... 7
PLAY AND CLEARANCE BETWEEN THE
BRAKE PEDAL AND FLOOR PANEL WITH
PEDAL DEPRESSED ........................................... 7
ADJUSTMENT ...................................................... 7
Components ............................................................. 8
Removal and Installation .......................................... 8
REMOVAL ............................................................. 8
INSPECTION AFTER REMOVAL ......................... 8
INSTALLATION ..................................................... 9
BRAKE FLUID .......................................................... 10
On-Vehicle Inspection ............................................ 10
LEVEL CHECK ................................................... 10
Drain and Refill ....................................................... 10
Bleeding Brake System ........................................... 11
BRAKE TUBE AND HOSE ....................................... 12
Hydraulic Circuit ..................................................... 12
Removal and Installation of the Front Brake Tube
and Brake Hose (Other than Brembo Calipers) ..... 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
Removal and Installation of the Front Brake Tube
and Brake Hose (With Brembo Calipers) ............... 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 13
Removal and Installation of the Rear Brake Tube
and Brake Hose (Other than Brembo Calipers) ..... 13REMOVAL ........................................................... 13
INSTALLATION ................................................... 14
Removal and Installation of the Rear Brake Tube
and Brake Hose (With Brembo Calipers) ............... 14
REMOVAL ........................................................... 14
INSTALLATION ................................................... 14
Inspection after Installation ..................................... 14
BRAKE MASTER CYLINDER .................................. 15
On-Vehicle Inspection ............................................. 15
LEAK INSPECTION ............................................ 15
Removal and Installation ........................................ 15
REMOVAL ........................................................... 15
INSTALLATION ................................................... 15
Components ........................................................... 16
Disassembly and Assembly .................................... 16
MODELS WITHOUT VDC ................................... 16
MODELS WITH VDC .......................................... 19
BRAKE BOOSTER ................................................... 23
On-Vehicle Inspection ............................................. 23
OPERATING CHECK .......................................... 23
AIRTIGHT CHECK .............................................. 23
Components ........................................................... 23
Removal and Installation ........................................ 24
REMOVAL ........................................................... 24
INSPECTION AFTER REMOVAL ....................... 24
INSTALLATION ................................................... 24
VACUUM LINES ....................................................... 25
Components ........................................................... 25
Removal and Installation ........................................ 25
Inspection ............................................................... 25
VISUAL INSPECTION ......................................... 25
CHECK VALVE INSPECTION ............................. 25
FRONT DISC BRAKE ............................................... 26
On-Vehicle Inspection ............................................. 26
PAD WEAR INSPECTION ................................... 26
Components ........................................................... 27
OTHER THAN BREMBO CALIPERS .................. 27
WITH BREMBO CALIPERS ................................ 28
Removal and Installation of Brake Pad (Other than
Brembo Calipers) .................................................... 29
Page 2 of 54
BR-2Revision: 2006 November2007 350Z REMOVAL ........................................................... 29
INSTALLATION .................................................... 29
Removal and Installation of Brake Pad (With
Brembo Calipers) .................................................... 30
REMOVAL ........................................................... 30
HOW TO APPLY GREASE TO THE BRAKE PAD ... 30
INSTALLATION .................................................... 30
Removal and Installation of Brake Caliper Assembly
(Other than Brembo Calipers) ................................ 31
REMOVAL ........................................................... 31
INSTALLATION .................................................... 31
Removal and Installation of Brake Caliper Assembly
(With Brembo Calipers) .......................................... 32
REMOVAL ........................................................... 32
INSTALLATION .................................................... 32
Disassembly and Assembly of Brake Caliper
Assembly (Other than Brembo Calipers) ................ 33
DISASSEMBLY ................................................... 33
INSPECTION AFTER DISASSEMBLY ................ 34
ASSEMBLY ......................................................... 34
DISC ROTOR INSPECTION ............................... 35
Disassembly and Assembly of Brake Caliper
Assembly (With Brembo Calipers) .......................... 36
DISASSEMBLY ................................................... 36
CALIPER INSPECTION ...................................... 36
ASSEMBLY ......................................................... 36
DISC ROTOR INSPECTION ............................... 37
Brake Burnishing Procedure ................................... 38
REAR DISC BRAKE ................................................. 39
On-Vehicle Inspection ............................................. 39
PAD WEAR INSPECTION ................................... 39
Components ........................................................... 40
OTHER THAN BREMBO CALIPERS .................. 40
WITH BREMBO CALIPERS ................................ 41
Removal and Installation of Brake Pad (Other than Brembo Calipers) .................................................... 42
REMOVAL ............................................................ 42
INSTALLATION .................................................... 42
Removal and Installation of Brake Pad (With
Brembo Calipers) .................................................... 42
REMOVAL ............................................................ 42
HOW TO APPLY GREASE TO THE BRAKE PAD ... 43
INSTALLATION .................................................... 43
Removal and Installation of Brake Caliper Assembly
(Other than Brembo Calipers) ................................. 44
REMOVAL ............................................................ 44
INSTALLATION .................................................... 44
Removal and Installation of Brake Caliper Assembly
(With Brembo Calipers) ........................................... 45
REMOVAL ............................................................ 45
INSTALLATION .................................................... 45
Disassembly and Assembly of Brake Caliper
Assembly (Other than Brembo Calipers) ................ 45
DISASSEMBLY .................................................... 45
CALIPER INSPECTION ....................................... 46
ASSEMBLY .......................................................... 47
DISC ROTOR INSPECTION ............................... 48
Disassembly and Assembly of Brake Caliper
Assembly (With Brembo Calipers) .......................... 49
DISASSEMBLY .................................................... 49
CALIPER INSPECTION ....................................... 49
ASSEMBLY .......................................................... 49
DISC ROTOR INSPECTION ............................... 50
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 52
General Specifications ............................................ 52
Brake Pedal ............................................................ 52
Brake Booster ......................................................... 52
Check Valve ............................................................ 52
Front Disc Brake ..................................................... 52
Rear Disc Brake ...................................................... 53
Page 3 of 54
PRECAUTIONS
BR-3
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NFS00001
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery ServiceNFS00002
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precautions for Procedures without Cowl Top CoverNFS000HT
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precautions for Brake SystemNFS00003
Recommended fluid is brake fluid “DOT 3”. Refer to MA-11, "Fluids and Lubricants" .
Do not reuse drained brake fluid.
Do not let brake fluid come in contact with painted surfaces on the body. This might damage the paint, so
if it does come in contact, immediately wipe area and wash off with water.
To clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.
Do not use mineral oils such as gasoline or kerosene. They will ruin rubber parts of the hydraulic system.
PIIB3706J
Page 5 of 54
PREPARATION
BR-5
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
PREPARATIONPFP:00002
Commercial Service ToolsNFS00004
Tool nameDescription
1. Flare nut crowfoot
a:10 mm (0.39 in)/12mm(0.47 in)
2. Torque wrenchInstalling each brake piping
Power toolLoosening bolts and nuts
Pin punch
Tip diameter: 4 mm (0.16 in) dia Removing and installing reservoir tank
pin
S-NT360
PBIC0190E
ZZA0515D
Page 17 of 54
BRAKE MASTER CYLINDER
BR-17
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
2. Attach the attachment in the inner kit to the reservoir cap as
shown in the figure.
CAUTION:
When attaching the attachment to the reservoir cap, make
sure it is pointing in the right direction.
3. Place the side of the cylinder body with chamfering around the
pin insertion hole facing up, and secure the master cylinder
assembly with a vise.
CAUTION:
Tighten without letting the pin securing the reservoir tank
and cylinder body come in contact with the pin insertion
hole of the reservoir tank.
When securing the master cylinder assembly with the
vise, be sure not to over-tighten.
When securing in a vise, use copper plates or cloth to
protect the flange.
4. Using a pin punch [commercial service tool: diameter approx. 4
mm (0.16 in)], remove mounting pin on the reservoir tank.
5. Remove master cylinder assembly from the vise.
6. Remove reservoir tank and grommet from cylinder body.
7. Using a Phillips flat-bladed screwdriver, push in the primary pis-
ton and remove the piston stopper from the cylinder body sec-
ondary-side tank boss hole.
8. Carefully pull the primary piston assembly straight out to prevent
cylinder inner wall from being damaged.
9. Tap flange using a soft block such as wood, and carefully pull
the secondary piston assembly straight out to prevent cylinder
inner wall from being damaged.
PFIA0262E
SFIA0699E
SFIA0250E
BRA0519D
BRA0033D
Page 19 of 54
BRAKE MASTER CYLINDER
BR-19
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
NOTE:
Attach the reservoir tank in the orientation shown in the figure.
8. Using a pin punch [commercial service tool: diameter Approx. 4
mm (0.16 in)], attach the reservoir tank mounting pin so that the
attachment side and the opposite side are identical.
CAUTION:
Do not reuse reservoir tank and mounting pin.
MODELS WITH VDC
Disassembly
CAUTION:
While working, cover the primary piston rod with cloth to prevent it from being damaged.
Only remove the reservoir tank when absolutely necessary.
1. Place the side of the cylinder body with chamfering around the
pin insertion hole up, and secure the cylinder body flange sec-
tion with a vise as shown in the figure.
CAUTION:
When securing in a vise, use copper plates or cloth to pro-
tect the flange.
2. Using a pin punch [commercial service tool: diameter Approx 4
mm (0.16 in)], remove the reservoir tank mounting pin.
3. Remove master cylinder assembly from the vise.
4. Remove reservoir tank and grommet from cylinder body.
BRA0568D
SFIA0250E
BRA0558D
BRA0559D
Page 30 of 54
BR-30
FRONT DISC BRAKE
Revision: 2006 November2007 350Z
Removal and Installation of Brake Pad (With Brembo Calipers)NFS0000W
REMOVAL
1. Remove tires from vehicle with a power tool.
2. Remove the clip from the pad pin.
3. Remove the pad pin while holding down the cross spring, then
remove the cross spring from the caliper.
4. Using pliers, remove the pad from the caliper.
HOW TO APPLY GREASE TO THE BRAKE PAD
Pad Side
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease
about 0.5 g (0.018 oz) per surface equally to back plate side of Inner
Pad and Outer Pad. (Refer to the figure.)
CAUTION:
Make sure no foreign matter attaches itself to the grease.
INSTALLATION
1. Insert the piston to the position where the pad is attached.
NOTE:
Using a disc brake piston tool (commercial service tool), etc., makes it easier to push in the piston.
CAUTION:
By pushing in the piston, the brake fluid returns to the master cylinder reservoir tank. Watch the
level of the surface of the reservoir tank.
PFIA0274E
BRB0328D
BRB0329D
PFIA0235E
Page 42 of 54
BR-42
REAR DISC BRAKE
Revision: 2006 November2007 350Z
Removal and Installation of Brake Pad (Other than Brembo Calipers)NFS00011
REMOVAL
1. Remove tires from vehicle with a power tool.
2. Remove sliding pin bold (one on top).
3. Hang cylinder body with a wire, and remove pads, pad retainers, shims and shim cover from torque mem-
ber.
INSTALLATION
1. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the rear of the pad and to both sides
of the shim, and attach the inner shim and shim cover to the inner pad, and the outer shim to the outer
pad.
2. Attach the pad retainer and pad to the torque member.
3. Push the piston in so that the pad is firmly attached and attach the cylinder body to the torque member.
NOTE:
Using a disc brake piston tool (commercial service tool), etc., makes it easier to push in the piston.
CAUTION:
By pushing in the piston, the brake fluid returns to the master cylinder reservoir tank. Watch the
level of the surface of the reservoir tank.
4. Attach the sliding pin bolt (one on top) and tighten to the specified torque.
5. Check brake for drag.
6. Install tires to vehicle.
Removal and Installation of Brake Pad (With Brembo Calipers)NFS00016
REMOVAL
1. Remove tires from vehicle with a power tool.
2. Remove the clip from the pad pin.
3. Remove the pad pin while holding down the cross spring, then
remove the cross spring from the caliper.
BRD0346D
BRD0347D
Page 43 of 54
REAR DISC BRAKE
BR-43
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
4. Using pliers, remove the pad from the caliper.
HOW TO APPLY GREASE TO THE BRAKE PAD
Pad Side
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease
about 0.5 g (0.018 oz) per surface equally to back plate side of Inner
Pad and Outer Pad. (Refer to the figure)
CAUTION:
Make sure no foreign matter attaches itself to the grease.
Pad Rear
Apply approximately 1.5 g (0.053 oz) of PBC (Poly Butyl Cuprysil)
grease or silicone -based grease between shim cover (1) and pad
(2).
A: Outer side
B: Inner side
CAUTION:
Make sure no foreign matter attaches itself to the grease.
INSTALLATION
1. Insert the piston to the position where the pad is attached.
NOTE:
Using a disc brake piston tool (commercial service tool), etc., makes it easier to push in the piston.
CAUTION:
Pushing the piston in will make the brake fluid return to the master cylinder reservoir tank, so
watch the level of the surface of the reservoir tank.
2. Attach pad and shim cover.
BRD0348D
PFIA0235E
PFIA0704E
Page 52 of 54
BR-52
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2006 November2007 350Z
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsNFS00019
Unit: mm (in)
Brake PedalNFS0001A
Brake BoosterNFS0001B
Check ValveNFS0001C
Front Disc BrakeNFS0001D
Brake model Other than brembo With brembo
Front brakeRotor outer diameter × thickness 320 × 28.0 (12.60 × 1.102) 324 × 30.0 (12.76 × 1.181)
Pad length × width × thickness130.0 × 50.0 × 11.0
(5.12 × 1.97 × 0.43)11 7 . 1 × 53.3 × 9.3
(4.61 × 2.098 × 0.366)
Cylinder bore diameter 45.0 × 2 (1.772 × 2) 38 (1.50) × 2 + 44 (1.73) × 2
Rear brake Rotor outer diameter × thickness 308 × 16 (12.13 × 0.63) 322 × 22 (12.68 × 0.87)
Pad length × width × thickness83.0 × 31.9 × 8.5
(3.27 × 1.26 × 0.335)76.6 × 45 × 9.1
(3.016 × 1.77 × 0.358)
Cylinder bore diameter 42.86 (1.6874) 40.0 × 2 (1.575)
Master cylinder Cylinder bore diameter 26.99 (1.0626)
Control valve Valve type Electric brake force distribution
Brake booster Diaphragm diameterCoupe 255 (10.04)Pri: 230 (9.06)
Sec: 205 (8.07)
RoadsterPri: 230 (9.06)
Sec: 205 (8.07)Pri: 230 (9.06)
Sec: 205 (8.07)
Recommended brake fluid DOT 3
Brake pedal height (from dash lower panel top surface)M/T models 153.2 – 163.2 mm (6.03 – 6.43 in)
A/T models 161.5 – 171.5 mm (6.36 – 6.75 in)
Depressed pedal height [under a force of 490 N (50 kg, 110 lb)
with the engine running]M/T models More than 90 mm (3.54 in)
A/T models More than 95 mm (3.74 in)
Clearance between threaded end of the stop lamp switch/ASCD cancel switch and
stopper rubber0.74 – 1.96 mm (0.0291 – 0.0772 in)
Pedal play3 – 11 mm (0.12 – 0.43 in)
Vacuum leakage
[at vacuum of −66.7 kPa (−500 mmHg, −19.69 inHg)]Within 3.3 kPa (25 mmHg, 0.98 inHg) of vacuum for 15 seconds
Output rod lengthWith TCS 10.4 mm (0.409 in)
With VDC−6.2 mm (−0.244 in)
Input rod length125 mm (4.92 in)
Vacuum leakage
[at vacuum of −66.7 kPa(−500 mmHg, −19.69 inHg)]Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
Brake model Other than brembo With brembo
Brake padStandard thickness (new) 11.0 mm (0.433 in) 9.3 mm (0.366 in)
Repair limit thickness 2.0 mm (0.079 in) 2.0 mm (0.079 in)
Disc rotorStandard thickness (new) 28.0 mm (1.102 in) 30.0mm (1.181 in)
Repair limit thickness 26.0 mm (1.024 in) 28.4mm (1.118 in)
Maximum uneven wear (measured at 8 positions) 0.015mm (0.0006 in) or less 0.015 mm (0.0006 in) or less
Runout limit (with it attached to the vehicle) 0.035 mm (0.0014 in) or less 0.040 mm (0.0016 in) or less
Runout limit (just the disc rotor) 0.020 mm (0.0008 in) or less 0.040 mm (0.0016 in) or less