key NISSAN 350Z 2007 Z33 Driver Information Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 92, PDF Size: 3.12 MB
Page 2 of 92
DI-2Revision: 2006 November2007 350Z REMOVAL ........................................................... 42
INSTALLATION .................................................... 42
Disassembly and Assembly for Triple Meters ......... 43
DISASSEMBLY ................................................... 43
ASSEMBLY ......................................................... 43
UNIFIED METER AND A/C AMP .............................. 44
System Description ................................................. 44
DESCRIPTION .................................................... 44
COMBINATION METER CONTROL FUNCTION ... 44
TRIPLE METER CONTROL FUNCTION ............ 45
A/C AUTO AMP. FUNCTION ............................... 45
OTHER FUNCTIONS .......................................... 45
Schematic ............................................................... 46
CONSULT-III Function (METER A/C AMP) ............ 47
SELF-DIAGNOSTIC RESULTS ........................... 47
DATA MONITOR .................................................. 47
Power Supply and Ground Circuit Inspection ......... 49
DTC [U1000] CAN Communication Circuit ............. 50
DTC [B2201] Triple Meter Communication Circuit ... 50
DTC [B2202] Meter Communication Circuit ............ 52
DTC [B2205] Vehicle Speed Circuit ........................ 55
Removal and Installation of Unified Meter and A/C
Amp. ....................................................................... 55
REMOVAL ........................................................... 55
INSTALLATION .................................................... 55
WARNING LAMPS .................................................... 56
System Description ................................................. 56
OIL PRESSURE WARNING LAMP ..................... 56
Schematic ............................................................... 57
Wiring Diagram — WARN — .................................. 58
CONSULT-III Function (METER A/C AMP) ............ 66
Oil Pressure Warning Lamp Stays Off (Ignition
Switch ON) or Stays On (Oil Pressure Is Normal) ... 66
A/T INDICATOR ........................................................ 67
System Description ................................................. 67
MANUAL MODE .................................................. 67
NOT MANUAL MODE ......................................... 67
Wiring Diagram — AT/IND — ................................. 68CONSULT-III Function (METER A/C AMP) ............ 70
A/T Indicator Is Malfunction .................................... 70
WARNING CHIME ..................................................... 71
System Description ................................................. 71
IGNITION KEY WARNING CHIME ...................... 71
LIGHT WARNING CHIME ................................... 71
SEAT BELT WARNING CHIME ........................... 72
Component Parts and Harness Connector Location ... 72
Schematic ............................................................... 73
Wiring Diagram — CHIME — ................................. 74
Terminals and Reference Value for BCM ................ 77
Terminals and Reference Value for Unified Meter
and A/C Amp. .......................................................... 81
Terminals and Reference Value for Combination
Meter ....................................................................... 81
CONSULT-III Function (METER A/C AMP) ............ 83
CONSULT-III Function (BCM) ................................. 83
DIAGNOSTIC ITEMS DESCRIPTION ................. 83
DATA MONITOR .................................................. 83
ACTIVE TEST ...................................................... 83
SELF-DIAGNOSTIC RESULTS ........................... 83
Trouble Diagnosis ................................................... 83
HOW TO PERFORM TROUBLE DIAGNOSIS .... 83
PRELIMINARY INSPECTION .............................. 84
Symptom Chart ....................................................... 84
Power Supply and Ground Circuit Inspection ......... 84
Meter Buzzer Circuit Inspection .............................. 85
Driver Side Door Switch Signal Inspection ............. 86
Key Switch Signal Inspection .................................. 87
Lighting Switch Signal Inspection ........................... 88
Seat Belt Buckle Switch (Driver Side) Signal Inspec-
tion .......................................................................... 88
Component Inspection ............................................ 90
DRIVER SIDE DOOR SWITCH ........................... 90
SEAT BELT BUCKLE SWITCH (DRIVER SIDE) ... 90
KEY SWITCH ....................................................... 90
CAN COMMUNICATION ........................................... 91
System Description ................................................. 91
CAN Communication Unit ....................................
Page 71 of 92
WARNING CHIME
DI-71
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2006 November2007 350Z
WARNING CHIMEPFP:24814
System DescriptionNKS00266
The buzzer for warning chime system is installed in the combination meter.
The buzzer sounds when the combination meter receives buzzer output signal from each unit through uni-
fied meter and A/C amp.
IGNITION KEY WARNING CHIME
With the key inserted into the key switch, and the ignition switch in OFF or ACC position, when driver's door is
open, the ignition key warning chime sounds.
BCM detects key inserted into the key switch, ignition switch in OFF or ACC position, and driver side door
switch ON. And then, BCM transmits buzzer output signal (ignition key warning chime) to unified meter
and A/C amp. with CAN communication.
Unified meter and A/C amp. transmits buzzer output signal (ignition key warning chime) to combination
meter with communication line.
When combination meter receives buzzer output signal (ignition key warning chime), it sounds the buzzer.
LIGHT WARNING CHIME
With ignition switch in OFF or ACC position, drivers door open, and lighting switch in 1ST or 2ND position, the
light warning chime will sounds.
BCM detects ignition switch in OFF or ACC position, driver side door switch ON, and lighting switch in
1ST or 2ND position. And then, BCM transmits buzzer output signal (light warning chime) to unified meter
and A/C amp. with CAN communication line.
Unified meter and A/C amp. transmits buzzer output signal (light warning chime) to combination meter
with communication line.
When combination meter receives buzzer output signal (light warning chime), it sounds the buzzer.
NOTE:
For further details of combination switch, refer to LT- 8 7 , "
Combination Switch Reading Function" .
PKIC4374E
PKIC4375E
Page 79 of 92
WARNING CHIME
DI-79
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2006 November2007 350Z
18 BRemote key-
less entry
receiver
(Ground)
——Refer to WT-20, "
Control Unit
Input/Output Signal Standard" . 19 YRemote key-
less entry
receiver
(Power sup-
ply)
20 LRemote key-
less entry
receiver (Sig-
nal)
32 G/BCombination
switch output
5ONLighting,
turn, wiper
switchOFF
(Wiper intermittent dial position 4)
7.2 V
Any of the conditions below
Wiper intermittent dial position 1
Wiper intermittent dial position 2
Wiper intermittent dial position 6
Wiper intermittent dial position 7
1.0 V
33 GCombination
switch output
4ONLighting,
turn, wiper
switchOFF
(Wiper intermittent dial position 4)
7.2 V
Any of the conditions below
Lighting switch 1ST (The same
result with lighting switch 2ND)
Rear wiper switch INT
Wiper intermittent dial position 1
Wiper intermittent dial position 5
Wiper intermittent dial position 6
1.2 V Terminal
No.Wire
colorSignal nameMeasuring condition
Reference value
(Approx.) Igni-
tion
switchOperation or condition
PKIB4960J
PKIB4956J
PKIB4960J
PKIB4958J
Page 81 of 92
WARNING CHIME
DI-81
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2006 November2007 350Z
Terminals and Reference Value for Unified Meter and A/C Amp. NKS0007L
Terminals and Reference Value for Combination MeterNKS0007M
37 B/RKey switch
signalOFFKey is removed. 0 V
Key is inserted. 12 V
38 W/LIgnition
power supplyON — Battery voltage
39 L CAN-H — — —
40 P CAN-L — — —
42 GYBattery
power sup-
ply (FUSE)OFF — Battery voltage
52 B Ground ON — 0 V
55 RBattery
power sup-
ply (F/L)OFF — Battery voltage
62 LDriver side
door switch
signalOFFDoor switch is released. (Door switch ON) 0 V
Door switch is pressed. (Door switch OFF) 5 V Terminal
No.Wire
colorSignal nameMeasuring condition
Reference value
(Approx.) Igni-
tion
switchOperation or condition
Terminal
No.Wire
colorItemMeasuring condition
Reference value
(Approx.) Ignition
switchOperation or condition
1 L CAN-H OFF — —
9L/ORTX communication line
(To combination meter)ON —
11 P C A N - L O F F — —
19 R/GRX communication line
(From combination meter)ON —
21 R/W Battery power supply OFF — Battery voltage
22 Y/G Ignition power supply ON — Battery voltage
29 B Ground (POWER) ON — 0 V
30 B Ground ON — 0 V
SKIA3362E
SKIA3361E
Te r m i -
nal No.Wire
colorItem Measuring condition
Reference value
(Approx.) Ignition
switchOperation or condition
1 BR/Y Seat belt buckle switch (Driver side) ONSeat belt is unfastened. 0 V
Seat belt is fastened. 5 V
Page 83 of 92
WARNING CHIME
DI-83
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2006 November2007 350Z
CONSULT-III Function (METER A/C AMP)NKS0007O
Refer to DI-47, "CONSULT-III Function (METER A/C AMP)" in “UNIFIED METER AND A/C AMP”.
CONSULT-III Function (BCM)NKS0007P
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
DIAGNOSTIC ITEMS DESCRIPTION
DATA MONITOR
Display Item List
ACTIVE TEST
Display Item List
SELF-DIAGNOSTIC RESULTS
Display Item List
NOTE:
If “CAN communication [U1000]” is indicated, after printing the monitor item, go to “CAN system”. Refer to
LAN-48, "
CAN System Specification Chart" .
Trouble DiagnosisNKS00267
HOW TO PERFORM TROUBLE DIAGNOSIS
1. Confirm the symptom and customer complaint.
2. Understand the outline of system. Refer to DI-71, "
System Description" .
3. Perform the preliminary inspection. Refer to DI-84, "
PRELIMINARY INSPECTION" .
4. Referring to trouble diagnosis chart, make sure the cause of the malfunction and repair or replace applica-
ble parts. Refer to DI-84, "
Symptom Chart" .
5. Does warning chime system operate normally? If yes, GO TO 6. If no, GO TO 4.
6. INSPECTION END
System Test item Diagnosis mode Description
BCMBCMSELF-DIAG
RESULTBCM performs self-diagnosis of CAN communication.
BUZZERDATA MONITOR The input data to the BCM control unit is displayed in real time.
ACTIVE TESTOperation of electrical loads can be checked by sending driving signal
to them.
Monitor item [Unit] ALL SIGNALSSELECTION
FROM MENUContents
IGN ON SW [ON/OFF] X X Indicates [ON/OFF] condition of ignition switch.
KEY ON SW [ON/OFF] X X Indicates [ON/OFF] condition of key switch.
DOOR SW-DR [ON/OFF] X X Indicates [ON/OFF] condition of driver side door switch.
LIGHT SW 1ST [ON/OFF] X X Indicates [ON/OFF] condition of lighting switch.
BUCKLE SW [ON/OFF] X X Indicates [ON/OFF] condition of seat belt switch.
Test item Malfunction is detected when···
LIGHT WARN ALM This test is able to check light warning chime operation.
IGN KEY WARN ALM This test is able to check ignition key warning chime operation.
SEAT BELT WARN ALM This test is able to check seat belt warning chime operation.
Display item [Code] Malfunction is detected when···
CAN communication [U1000] Malfunction is detected in CAN communication.
Page 84 of 92
DI-84
WARNING CHIME
Revision: 2006 November2007 350Z
PRELIMINARY INSPECTION
1. CHECK BCM (CONSULT-III)
Perform self-diagnosis of BCM. Refer to BCS-15, "
CONSULT-III Function (BCM)" .
Self
-diagnostic results
No malfunction detected>> GO TO 2.
Malfunction detected>> Check applicable parts, and repair or replace corresponding parts.
2. CHECK UNIFIED METER AND A/C AMP. (CONSULT-III)
Perform self-diagnosis of unified meter and A/C amp. Refer to DI-47, "
CONSULT-III Function (METER A/C
AMP)" .
Self
-diagnostic results
No malfunction detected>> INSPECTION END
Malfunction detected>> Check applicable parts, and repair or replace corresponding parts.
Symptom ChartNKS00268
Power Supply and Ground Circuit InspectionNKS00269
1. CHECK FUSE AND FUSIBLE LINK
Check for blown BCM fuse and fusible link.
OK or NG
OK >> GO TO 2.
NG >> Be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-4, "
POWER
SUPPLY ROUTING CIRCUIT" .
Symptom Diagnoses/Service procedure
All warning chimes do not activate.Perform the following inspections.
1.DI-84, "
Power Supply and Ground Circuit Inspection".
2.DI-85, "
Meter Buzzer Circuit Inspection".
Replace BCM, found normal function in the above inspections.
Ignition key warning chime does not activate.Perform the following inspections.
1.DI-87, "
Key Switch Signal Inspection".
2.DI-86, "
Driver Side Door Switch Signal Inspection".
Replace BCM, found normal function in the above inspection.
Light warning chime does not activate.Perform the following inspections.
1.DI-88, "
Lighting Switch Signal Inspection".
2.DI-86, "
Driver Side Door Switch Signal Inspection".
Replace BCM, found normal function in the above inspection.
Seat belt warning chime does not activate.Perform DI-88, "
Seat Belt Buckle Switch (Driver Side) Signal
Inspection" .
Replace BCM, found normal function in the above inspection.
Unit Power source Fuse and fusible link No.
BCMBatteryF
18
Ignition switch ON or START 1
Page 85 of 92
WARNING CHIME
DI-85
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2006 November2007 350Z
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between BCM harness connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness between BCM and fuse.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector M91 terminal
52 and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Meter Buzzer Circuit InspectionNKS0026F
1. CHECK OPERATION OF METER BUZZER
1. Select “BUZZER” of “BCM” on CONSULT-III.
2. Perform “LIGHT WARN ALM”, “IGN KEY WARN ALM” or “SEAT BELT WARN ALM” of “ACTIVE TEST”.
Does meter buzzer beep?
YES >> GO TO 3.
NO >> GO TO 2.
2. CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL
1. Select “METER A/C AMP” on CONSULT-III.
2. With “DATA MONITOR”, confirm “BUZZER” under the condition of buzzer input. (Seat belt warning chime,
turn signal lamp operate, etc.)
OK or NG
OK >> Replace combination meter.
NG >> Replace BCM. Refer to BCS-17, "
Removal and Installation of BCM" .
Terminals Ignition switch position
(+)
(–) OFF ON
ConnectorTerminal
(Wire color)
M9142
GroundBattery voltage Battery voltage
55
M90 38 0 V Battery voltage
SKIB2802E
52 – Ground : Continuity should exist.
SKIA9667E
“BUZZER”
Under the condition of buzzer input : ON
Except above : OFF
Page 87 of 92
WARNING CHIME
DI-87
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2006 November2007 350Z
3. CHECK DRIVER SIDE DOOR SWITCH
Check driver side door switch. Refer to DI-90, "
DRIVER SIDE DOOR SWITCH" .
OK or NG
OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM" .
NG >> Replace driver side door switch.
Key Switch Signal InspectionNKS0026B
1. CHECK FUSE
Check if the key switch 10A fuse [No. 21, located in the fuse block (J/B)] is blown.
OK or NG
OK >> GO TO 2.
NG >> Be sure to repair the cause of malfunction before installing new fuse. Refer to PG-4, "
POWER
SUPPLY ROUTING CIRCUIT" .
2. CHECK BCM INPUT SIGNAL
With CONSULT-llI
1. Select “BCM”.
2. With “DATA MONITOR” of “BUZZER”, confirm “KEY ON SW” when the key switch is operated.
Without CONSULT-llI
Check voltage between BCM harness connector M90 terminal 37
and ground.
OK or NG
OK >> INSPECTION END
NG >> GO TO 3.
3. CHECK KEY SWITCH
Check continuity between key switch. Refer to DI-90, "
Component Inspection" .
OK or NG
OK >> GO TO 4.
NG >> Replace key switch.“KEY ON SW”
When key is inserted to ignition key cylinder : ON
When key is removed from ignition key cylinder : OFF
37 – Ground
When key is inserted to
ignition key cylinder: Approx. 12 V
When key is removed from
ignition key cylinder: Approx. 0 V
SKIA5048E
Page 88 of 92
DI-88
WARNING CHIME
Revision: 2006 November2007 350Z
4. CHECK KEY SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M90 terminal
37 and key switch harness connector M25 terminal 1.
3. Check continuity between BCM harness connector M90 terminal
37 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK KEY SWITCH POWER SUPPLY CIRCUIT
Check voltage between key switch harness connector M25 terminal
2 and ground.
OK or NG
OK >> Replace BCM. Refer to BCS-17, "Removal and Installa-
tion of BCM" .
NG >> Check continuity between key switch and fuse.
Lighting Switch Signal Inspection NKS0026C
1. CHECK BCM INPUT SIGNAL
1. Select “BCM” on CONSULT-III.
2. With “DATA MONITOR” of “BUZZER”, confirm “LIGHT SW 1ST”
when the lighting switch is operated.
OK or NG
OK >> INSPECTION END
NG >> Check lighting switch. Refer to LT- 9 2 , "
Combination
Switch Inspection" .
Seat Belt Buckle Switch (Driver Side) Signal InspectionNKS0026D
1. CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) SIGNAL INPUT (BCM)
1. Select “BCM” on CONSULT-III.
2. With “DATA MONITOR” of “BUZZER”, confirm “BUCKLE SW” when the seat belt buckle switch (driver
side) is operated.
OK or NG
OK >> INSPECTION END
NG >> GO TO 2.37 – 1 : Continuity should exist.
37 – Ground : Continuity should not exist.
PKIB3833E
2 – Ground : Battery voltage
SKIA5051E
“LIGHT SW 1ST”
Lighting switch (1st position) : ON
Lighting switch (OFF) : OFF
PKIB1956E
“BUCKLE SW”
When seat belt is fastened : OFF
When seat belt is unfastened : ON
Page 90 of 92
DI-90
WARNING CHIME
Revision: 2006 November2007 350Z
Component InspectionNKS0026E
DRIVER SIDE DOOR SWITCH
Check continuity between terminal 1 and door switch case ground.
SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Check continuity between terminals 1 and 2.
KEY SWITCH
Check continuity between key switch terminals 1 and 2.1 – Door switch case ground
When driver side door
switch is released: Continuity should exist.
When driver side door
switch is pressed: Continuity should not exist.
PKIA3718E
1 – 2
When seat belt (driver side)
is fastened: Continuity should not
exist.
When seat belt (driver side)
is unfastened: Continuity should
exist.
SKIB4802E
1 – 2
When key is inserted to
ignition key cylinder: Continuity should exist.
When key is removed from
ignition key cylinder: Continuity should not
exist.
SKIA5049E