reset NISSAN 350Z 2007 Z33 Engine Control Workshop Manual

ENGINE CONTROL SYSTEM
EC-25
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
Multiport Fuel Injection (MFI) SystemNBS0002I
INPUT/OUTPUT SIGNAL CHART
*1: This sensor is not used to control the engine system under normal conditions.
*2: This signal is sent to the ECM through CAN communication line.
*3: ECM determines the start signal status by the signals of engine speed and battery voltage.
SYSTEM DESCRIPTION
The amount of fuel injected from the fuel injector is determined by the ECM. The ECM controls the length of
time the valve remains open (injection pulse duration). The amount of fuel injected is a program value in the
ECM memory. The program value is preset by engine operating conditions. These conditions are determined
by input signals (for engine speed and intake air) from both the crankshaft position sensor and the mass air
flow sensor.
VARIOUS FUEL INJECTION INCREASE/DECREASE COMPENSATION
In addition, the amount of fuel injected is compensated to improve engine performance under various operat-
ing conditions as listed below.


During warm-up

When starting the engine

During acceleration

Hot-engine operation
22.Exhaust valve timing control magnet
retarder23. A/F sensor 1 24. Heated oxygen sensor 2
25. Knock sensor 26. Crankshaft position sensor (POS) 27. Engine oil temperature sensor
28. Knock sensor 29. Three way catalyst 1 30. Three way catalyst 2
31. Three way catalyst 1 32. Three way catalyst 2 33. Muffler
34. EVAP canister vent control valve 35.EVAP control system pressure sen-
sor36. EVAP service port
37.EVAP canister purge volume con-
trol solenoid valve38. EVAP canister 39. Fuel camper
40. Fuel pump 41. Fuel pressure regulator 42. Fuel level sensor
43. Fuel tank temperature sensor 44. Fuel tank 45. Accelerator pedal position sensor
46. Electric throttle control actuator 47. Throttle position sensor 48.Mass air flow sensor (with intake air
temperature sensor)
49. Air cleaner 50. Electric throttle control actuator 51. Throttle position sensor
52.Mass air flow sensor (with intake air
temperature sensor)53. Air cleaner
Sensor Input Signal to ECM ECM function Actuator
Crankshaft position sensor (POS)
Engine speed*
3
Piston position
Fuel injection
& mixture ratio
controlFuel injector Camshaft position sensor (PHASE)
Mass air flow sensor Amount of intake air
Engine coolant temperature sensor Engine coolant temperature
Air fuel ratio (A/F) sensor 1 Density of oxygen in exhaust gas
Throttle position sensor Throttle position
Accelerator pedal position sensor Accelerator pedal position
Park/neutral position (PNP) switch Gear position
Knock sensor Engine knocking condition
Battery
Battery voltage*
3
Power steering pressure sensor Power steering operation
Heated oxygen sensor 2*
1Density of oxygen in exhaust gas
Air conditioner switch
Air conditioner operation*
2
Wheel sensor
Vehicle speed*2

EC-66
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: 2006 November2007 350Z

When the same malfunction is detected in two consecutive trips, the DTC and the freeze frame data are
stored in the ECM memory, and the MIL will come on. For details, refer to EC-47, "
Two Trip Detection
Logic" .

The MIL will go off after the vehicle is driven 3 times (driving pattern B) with no malfunction. The drive is
counted only when the recorded driving pattern is met (as stored in the ECM). If another malfunction
occurs while counting, the counter will reset.

The DTC and the freeze frame data will be stored until the vehicle is driven 40 times (driving pattern A)
without the same malfunction recurring (except for Misfire and Fuel Injection System). For Misfire and
Fuel Injection System, the DTC and freeze frame data will be stored until the vehicle is driven 80 times
(driving pattern C) without the same malfunction recurring. The “TIME” in “SELF-DIAGNOSTIC
RESULTS” mode of CONSULT-III will count the number of times the vehicle is driven.

The 1st trip DTC is not displayed when the self-diagnosis results in OK for the 2nd trip.
SUMMARY CHART
For details about patterns B and C under “Fuel Injection System” and “Misfire”, see EC-68 .
For details about patterns A and B under “Other”, see EC-70
.
*1: Clear timing is at the moment OK is detected.
*2: Clear timing is when the same malfunction is detected in the 2nd trip.Items Fuel Injection System Misfire Other
MIL (goes off) 3 (pattern B) 3 (pattern B) 3 (pattern B)
DTC, Freeze Frame Data (no
display)80 (pattern C) 80 (pattern C) 40 (pattern A)
1st Trip DTC (clear)
1 (pattern C), *
11 (pattern C), *11 (pattern B)
1st Trip Freeze Frame Data
(clear)*1, *2 *1, *2 1 (pattern B)

TROUBLE DIAGNOSIS
EC-123
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.VHCL SPEED SE [km/
h] or [mph]

The vehicle speed computed from the vehicle speed
signal sent from TCM is displayed.
SET VHCL SPD
[km/h] or [mph]

The preset vehicle speed is displayed.
MAIN SW
[ON/OFF]

Indicates [ON/OFF] condition from MAIN switch sig-
nal.
CANCEL SW
[ON/OFF]

Indicates [ON/OFF] condition from CANCEL switch
signal.
RESUME/ACC SW
[ON/OFF]

Indicates [ON/OFF] condition from RESUME/ACCEL-
ERATE switch signal.
SET SW
[ON/OFF]

Indicates [ON/OFF] condition from SET/COAST
switch signal.
BRAKE SW1
[ON/OFF]

Indicates [ON/OFF] condition from ASCD brake switch
signal and ASCD clutch switch signal (M/T)
BRAKE SW2
[ON/OFF]

Indicates [ON/OFF] condition of stop lamp switch sig-
nal.
VHCL SPD CUT
[NON/CUT]

Indicates the vehicle cruise condition.
NON: Vehicle speed is maintained at the ASCD set
speed.
CUT: Vehicle speed decreased to excessively low
compared with the ASCD set speed, and ASCD oper-
ation is cut off.
LO SPEED CUT
[NON/CUT]

Indicates the vehicle cruise condition.
NON: Vehicle speed is maintained at the ASCD set
speed.
CUT: Vehicle speed decreased to excessively low, and
ASCD operation is cut off.
AT OD MONITOR
[ON/OFF]

Indicates [ON/OFF] condition of A/T O/D according to
the input signal from the TCM.
For M/T models always “OFF” is displayed.
AT OD CANCEL
[ON/OFF]

Indicates [ON/OFF] condition of A/T O/D cancel
request signal.
For M/T models always “OFF” is displayed.
CRUISE LAMP
[ON/OFF]

Indicates [ON/OFF] condition of CRUISE lamp deter-
mined by the ECM according to the input signals.
SET LAMP
[ON/OFF]

Indicates [ON/OFF] condition of SET lamp determined
by the ECM according to the input signals.
EXH V/T LEARN [YET/
CMPLT]

Display the condition of Exhaust Valve Timing Control
Learning
YET: Exhaust Valve Timing Control Learning has not
been performed yet.
CMPLT: Exhaust Valve Timing Control Learning has
already been performed successfully.
A/F ADJ-B1

Indicates the correction of factor stored in ECM. The
factor is calculated from the difference between the
target air-fuel ratio stored in ECM and the air-fuel ratio
calculated from A/F sensor 1 signal. A/F ADJ-B2
Voltage [V]

Voltage, frequency, duty cycle or pulse width mea-
sured by the probe.

Only “#” is displayed if item is unable to be
measured.

Figures with “#”s are temporary ones. They
are the same figures as an actual piece of data
which was just previously measured. Frequency [msec], [Hz]
or [%]
DUTY-HI
DUTY-LOW
PLS WIDTH-HI
PLS WIDTH-LOWMonitored item [Unit] Description Remarks

EC-126
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
INSPECTION PROCEDURE
1. Turn ignition switch OFF.
2. Connect GST to data link connector (1), which is located under
LH dash panel near the hood opener handle.
3. Turn ignition switch ON.
4. Enter the program according to instruction on the screen or in
the operation manual.
(*: Regarding GST screens in this section, sample screens are
shown.)
Service $04 CLEAR DIAG INFOThis diagnostic service can clear all emission-related diagnostic information. This
includes:

Clear number of diagnostic trouble codes (Service $01)

Clear diagnostic trouble codes (Service $03)

Clear trouble code for freeze frame data (Service $01)

Clear freeze frame data (Service $02)

Reset status of system monitoring test (Service $01)

Clear on board monitoring test results (Service $06 and $07)
Service $06 (ON BOARD TESTS)This diagnostic service accesses the results of on board diagnostic monitoring tests of
specific components/systems that are not continuously monitored.
Service $07 (ON BOARD TESTS)This diagnostic service enables the off board test drive to obtain test results for emission-
related powertrain components/systems that are continuously monitored during normal
driving conditions.
Service $08 —This diagnostic service can close EVAP system in ignition switch ON position (Engine
stopped). When this diagnostic service is performed, EVAP canister vent control valve
can be closed.
In the following conditions, this mode cannot function.

Low ambient temperature

Low battery voltage

Engine running

Ignition switch OFF

Low fuel temperature

Too much pressure is applied to EVAP system
Service $09 (CALIBRATION ID)This diagnostic service enables the off-board test device to request specific vehicle infor-
mation such as Vehicle Identification Number (VIN) and Calibration IDs. Diagnostic test mode Function
2 : Hood opener handle
PBIB3500E
SEF398S

EC-130
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
IDL A/V LEARN
Engine: RunningIdle air volume learning has not been
performed yet.YET
Idle air volume learning has already
been performed successfully.CMPLT
ENG OIL TEMP

Engine: After warming up More than 70°C (158°F)
TRVL AFTER MIL

Ignition switch: ONVehicle has traveled after MIL has
turned ON.0 - 65,535 km
(0 - 40,723 mile)
A/F S1 HTR(B1)
A/F S1 HTR(B2)

Engine: After warming up, idle the engine
(More than 140 seconds after starting engine)4 - 100%
AC PRESS SEN

Engine: Idle

Both A/C switch and blower switch are ON.
(Compressor operates.)1.0 - 4.0V
VHCL SPEED SE

Turn drive wheels and compare CONSULT-III value with the speedometer
indication.Almost the same speed as the
speedometer indication
SET VHCL SPD

Engine: Running ASCD: OperatingThe preset vehicle speed is
displayed.
MAIN SW

Ignition switch: ONMAIN switch: Pressed ON
MAIN switch: Released OFF
CANCEL SW

Ignition switch: ONCANCEL switch: Pressed ON
CANCEL switch: Released OFF
RESUME/ACC SW

Ignition switch: ONRESUME/ACCELERATE switch:
PressedON
RESUME/ACCELERATE switch:
ReleasedOFF
SET SW

Ignition switch: ONSET/COAST switch: Pressed ON
SET/COAST switch: Released OFF
BRAKE SW1
(ASCD brake switch)

Ignition switch: ON

Brake pedal: Fully released (A/T)

Brake pedal and clutch pedal: Fully
released (M/T)ON

Brake pedal: Slightly depressed (A/T)

Brake pedal and/or clutch pedal:
Slightly depressed (M/T)OFF
BRAKE SW2
(Stop lamp switch)

Ignition switch: ONBrake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
VHCL SPD CUT

Ignition switch: ON NON
LO SPEED CUT

Ignition switch: ON NON
AT OD MONITOR

Ignition switch: ON OFF
AT OD CANSEL

Ignition switch: ON OFF
CRUISE LAMP

Ignition switch: ONMAIN switch: Pressed at the 1st time →
at the 2nd timeON → OFF
SET LAMP

MAIN switch: ON

When vehicle speed is between
40 km/h (25 MPH) and 144 km/h
(89MPH)ASCD: Operating ON
ASCD: Not operating OFF
EXH V/T LEARN

Engine: RunningExhaust Valve Timing Control Learning
has not been performed yet.YET
Exhaust Valve Timing Control Learning
has not been performed yet.CMPLT
A/F ADJ B1

Engine: Running –0.330 - 0.330
A/F ADJ B2

Engine: Running –0.330 - 0.330 MONITOR ITEM CONDITION SPECIFICATION